We use cookies and similar tools for site analytics and advertising. By using our site, you agree to this. See our Privacy Policy for details. Do Not Sell or Share My Personal Information
Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Secures the dishwasher sump or sump cover to the tub for a tight, leak-resistant seal. Replace if missing, stripped, or damaged to restore stability.
Fix a dishwasher that won't fill, overfills, or leaks from the base. Water inlet valve controls flow into the tub. Moderate DIY repair, 30-45 minutes.
Bacteria buildup in the venting assembly and drain hose. Replaced them and it's back to normal Read more
Includes door latch, strike plate and microswitch.
I ordered the latch from ApplianceParts and had the whole job done in 20 minutes. Shipping was super fast and the videos were helpful. Read more
This upper trim strip finishes the top edge of the appliance's front opening, restoring a clean look and helping protect nearby components. Replace a cracked, missing, or loose strip to keep panels aligned and secure.
My micro filter was in pieces when I pulled it out. Read more
Replacement screw for dishwashers. Secures panels and internal components. Needed when original is stripped, missing, or damaged during repairs.
Bought the parts per the schematic AppliancePartsPros.com provided (which was super helpful). Installed them with the help of the videos and, boom, all fixed up. Read more
The Float is an OEM part for Bosch dishwashers. This float senses water levels inside the dishwasher, signaling the inlet valve to refill when needed.
Causes of a float malfunctioning can be mineral deposits accumulating and weighing it down over time, or cracks in the plastic housing allowing water in.
Symptoms of a bad float include:
This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.
Replaced the defective float switch. Read more
Wax motor for detergent/rinse-aid dispenser.
Took door off, saw that dispenser linkage was ok, I could open and close by hand, so figured the wax motor or the wiring to it were most likely the problem. I took off the wax motor ( actuator) and ran 120 volts to it via jumper wires, and it did not move at all, so figured good chance that was the problem. Found part # on your site, received new one quickly from you, put it in and works great. Thanks. Read more
Fix a dispenser door that won't stay closed or rinse aid light staying on. Complete assembly includes latch, spring, and gasket. DIY-friendly repair.
Replaced the dispenser. The video on your website was most helpful and made replacement very easy with the little tips to show removal and install of new part. Read more
This pressure chamber is part of the water level sensing system in the dishwasher. It connects to the tub and the water level sensor, using air pressure changes to detect how much water has filled the machine so it knows when to stop filling. Replace this component if the dishwasher overfills, underfills, or displays water level error codes during a wash cycle.
Using instructions I obtained over the internet, I first removed the DW's bottom cover panels so I could look inside the DW (with a flashlight) while it was running. I had to put their dishwasher through several wash cycles before I could pinpoint the location of the leak. (The water appeared to be coming from above on the left side of the DW, near the top, rear of the DW's blue "Pressure Chamber." Thinking that the problem likely lay in either a malfunctioning Pressure Chamber or in a... Read more
O-ring seal prevents leaks between dishwasher components. Replace when you notice water drips or moisture buildup. Confirm fit with your model number.
WE replaced the drain pump and it still wouldn't drain sometimes. Finally we realized that the drain hose wasn't the correct bosch hose and the rubber was starting to bend and kink where it went through the hole to under the sink.So we bought the drain hose and replaced. Read more
Gray plastic clip that secures folding tines to the dishwasher rack rail. Snaps onto the rack assembly to hold flip tines in place. Replace broken or missing clips.
After having seen the video I installed the new lid and it worked. Read more
Rear pump housing for the washer drain/pump assembly. Replaces the worn rear housing that supports the impeller and bearing, helping restore proper draining and reduce leaks or unusual pump noises when the housing fails. What it does:
Our Bosch suddenly quit washing the dishes properly after 15 years of faithful service. I observed that there was no pressure coming from the sprayers, and determined it to be the circulating pump. I could reach into the pump from inside the dishwasher and could feel that something was loose in there - the impeller moved when pumping, but I could stop it with my finger. When I took the pump out and disassembled it, the impeller was in two pieces (the front and back pieces that are supposed... Read more
Replace a broken, worn, or missing dishwasher leveling leg. This adjustable foot installs at the front corner to stabilize and level your appliance.
This is a screw. This is a genuine Bosch replacement screw and has been sourced directly from the manufacturer. This replacement part is a high-quality piece of standard hardware with many different applications. This Bosch screw is intended for use with multiple different dishwasher models. It's common over time and with regular usage for screws to easily become stripped, rusted, broken, or lost. This can lead to improper functionality of appliances. It's important to always use genuine manufacturer replacement screws to ensure the highest-quality materials and a proper fit. When installing screws, always follow proper guidelines and abide by appropriate safety measures. For proper installation instructions and usage guidance, it is always recommended to refer to the equipment diagram supplied specifically by the manufacturer. This replacement screw is designed to work with various models of dishwashers manufactured by Bosch, Thermador, and Gaggenau. Please note this screw is a genuine OEM part made of high-quality, durable, non-corrosive metal and is sold individually.
I used APP's video to take apart my dishwasher's door and install the new endcap. The video was exactly correct for my model, but the comments from other customers filled in the gap. I'm very pleased with APP because I could easily find an obscure part for an older dishwasher, order it easily and inexpensively, have it delivered to my door, and get help with the installation. All good! Read more
This replacement screw secures appliance panels and internal brackets so components stay tight and aligned during everyday use. Replacing missing or stripped hardware restores a solid fit and helps minimize vibration and rattling.
Ordered parts and put them on. Read more
Single Torx T20 screw secures dishwasher panels, brackets, and trim. Replace missing, stripped, or damaged fasteners to keep components tight.
The dishwasher was leaking from the lower right corner of the door. I ordered new seals for the door perimeter and the base. As I pulled the hinge covers, I noted that the right hinge bushing was damaged. I ordered two new bushings.that evening and, with their usual efficiency, AppliancePartsPro.com processed and shipped my order the next morning. The parts were at my door on the third day. Whether the leak contributed to the bushing damage, I'm not qualified to say. The point is it never... Read more