Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Fix dishwasher not heating or running for hours. This NTC temperature sensor monitors water temp and prevents overheating. Moderate DIY repair with video.
Ordered new heater/thermostat piece. Read more
Fix a broken or cracked dishwasher handle cap. This end cap secures to the door handle. DIY-friendly repair takes about 20-30 minutes with basic tools.
One end cap was broken but I ordered 2 since the shipping was the same price. I replaced both by removing the Tork screws on both sides of the door panel (one side at a time). There was a bolt on the inside panel of the door that secured the end cap. I replaced the end cap and tightened the bolt moderately so as to not crack the plastic end cap. Total job was 30 mins replacing both end caps and including figuring out how to get to them. NOTE - be careful to not open the door panel sections... Read more
Replacement water feed tube that delivers water to the upper spray arm in your dishwasher. Replace if cracked, split at seams, or leaking due to wear.
After we saw that progressively our dishes were not getting clean we investigated the condition of the spray arms and this upper feed tube assembly. We found a huge crack on the side of this piece and new not enough water was getting to the arms. We also noticed a build up of soap and lime. So we ran a cycle of vinegar and sprayed the filters and arms with lime-off-sprayed them out with a air hose "completely". Many of the small pieces of lime will clog the holes in the spray arms. Attached the... Read more
This pressure chamber is part of the water level sensing system in the dishwasher. It connects to the tub and the water level sensor, using air pressure changes to detect how much water has filled the machine so it knows when to stop filling. Replace this component if the dishwasher overfills, underfills, or displays water level error codes during a wash cycle.
Using instructions I obtained over the internet, I first removed the DW's bottom cover panels so I could look inside the DW (with a flashlight) while it was running. I had to put their dishwasher through several wash cycles before I could pinpoint the location of the leak. (The water appeared to be coming from above on the left side of the DW, near the top, rear of the DW's blue "Pressure Chamber." Thinking that the problem likely lay in either a malfunctioning Pressure Chamber or in a... Read more
Replacement screw for dishwashers. Secures panels and internal components. Needed when original is stripped, missing, or damaged during repairs.
Bought the parts per the schematic AppliancePartsPros.com provided (which was super helpful). Installed them with the help of the videos and, boom, all fixed up. Read more
Fix a dishwasher that won't fill, overfills, or leaks from the base. Water inlet valve controls flow into the tub. Moderate DIY repair, 30-45 minutes.
Bacteria buildup in the venting assembly and drain hose. Replaced them and it's back to normal Read more
This upper trim strip finishes the top edge of the appliance's front opening, restoring a clean look and helping protect nearby components. Replace a cracked, missing, or loose strip to keep panels aligned and secure.
Appliance Parts Pro online , on line help gave me exact measurements to insure I was ordering correct piece as a women not used to order appliance parts this really helped ...thanks Parts Pro Read more
The Water Inlet Fill Hose is an OEM part for Bosch dishwashers. This part is responsible for safely and efficiently connecting the dishwasher to your home's water supply, ensuring that water flows into the dishwasher at the correct pressure and volume for optimal cleaning performance.
Over time, the Water Inlet Fill Hose can become susceptible to wear and tear, leaks and blockages.
Symptoms indicating the need for a new Water Inlet Fill Hose include:
This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.
Replaced the Water Inlet Valve and Drain Hose. Read more
O-ring seal prevents leaks between dishwasher components. Replace when you notice water drips or moisture buildup. Confirm fit with your model number.
WE replaced the drain pump and it still wouldn't drain sometimes. Finally we realized that the drain hose wasn't the correct bosch hose and the rubber was starting to bend and kink where it went through the hole to under the sink.So we bought the drain hose and replaced. Read more
Secures the dishwasher sump or sump cover to the tub for a tight, leak-resistant seal. Replace if missing, stripped, or damaged to restore stability.
The Float is an OEM part for Bosch dishwashers. This float senses water levels inside the dishwasher, signaling the inlet valve to refill when needed.
Causes of a float malfunctioning can be mineral deposits accumulating and weighing it down over time, or cracks in the plastic housing allowing water in.
Symptoms of a bad float include:
This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.
Replaced the defective float switch. Read more
Fix dirty dishes or weak water spray with a new dishwasher spray arm. Easy 5-minute DIY repair—just unclip the old arm and snap in the replacement.
Very easy to replace, as there are only two clips to flip up, and remove the sprayer arm. The new part was place on the water supply (hub), and cliped into place. Voila! Works like new again! Read more
Detergent not dispensing during wash cycle? This actuator arm with spring releases the detergent cup at the right time. Moderate DIY repair.
Ordered a replacement control panel and installed it according to the AppliancePartsPros.com YouTube video. Read more
This replacement screw secures appliance panels and internal brackets so components stay tight and aligned during everyday use. Replacing missing or stripped hardware restores a solid fit and helps minimize vibration and rattling.
Ordered parts and put them on. Read more
This factory screw secures appliance components per the original design, helping stop looseness and vibration. Replace a missing, stripped, or corroded fastener to restore a solid, rattle-free fit and protect nearby parts from damage.
Ordered parts from you and installed. I ordered the parts on Thursday evening and they arrived Saturday. Fast shipping! Read more
Black adapter connects dishwasher drain hose to another hose or fitting for secure wastewater routing. Replace when cracked, loose, or missing for leak-free.
Ordered a new drain hose and coupling to attach to the garbage disposal. Parts arrived in less than a day, awesome. Watched video on your site showing how to do it. Video is good but I needed to remove from base plate and side panel attached with star screws to get to the point the video showed. Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.