Wcr683dzd Parts

Size: 10-12 a. Includes 12 screws.

This locking clip secures a mating part—often a control knob—onto its shaft on select laundry appliances. Replacing a worn or missing clip restores a tight fit so controls stay in place and operate as intended during use.

• Locks a knob, lever, or similar component onto its shaft/post to prevent it from slipping off
• Maintains a firm fit to reduce wobble and intermittent control engagement
• Replace if the clip is bent, fatigued, corroded, or missing
• Typical symptoms include a knob that falls off, feels loose, or spins without engaging

• Disconnect power to the appliance; turn off water supply for washers
• Pull the affected component straight off to access the clip
• Use needle-nose pliers to remove/install the clip; avoid deforming it
• Ensure the clip is fully seated; test for a snug fit before reassembly

This washer water level pressure switch senses tub fill via air pressure and tells the control when to stop filling and advance. Replacing a failed switch restores accurate water levels to prevent overfilling, underfilling, and cycle stalls.

• Monitors air pressure from the tub through a small hose to determine the selected water level
• Signals the timer/control to open/close the inlet valves and move the cycle to agitation/spin
• Symptoms include overfilling or not stopping fill, little or no fill, or cycles that won't advance because "full" isn't detected
• Water level doesn't match the selector setting or changes unpredictably

• Disconnect power and shut off water supply before servicing
• Access the control console; label or photograph wire locations and transfer them to the new switch one at a time
• Move the existing pressure hose to the new switch; ensure the hose is clear, not kinked or cracked, and fully seated
• Reinstall the knob/control panel and test fill at multiple level settings; access and steps may vary by model

Control the water going into your washer with this triple water inlet valve. Three solenoids open and close to deliver water to the correct fill circuits or dispensers so cycles start and dispensing happens where it should.

• Regulates water flow into the washer when energized by the control
• Routes water to the correct fill path or dispenser compartment via three independently controlled outlets
• Common symptoms: no fill or slow fill, only certain cycles/dispensers receive water, water drips into the tub when off, or leaks at the valve/hose connections

• Unplug the washer and shut off the water supply before servicing
• Place towels, disconnect inlet hoses, and label/photograph wire connectors and outlet hoses for correct reassembly
• Transfer any mounting hardware from the old valve if required; ensure hoses/orientation match their original positions
• Restore water and power, then check all connections for leaks and run a test fill

This double-style hinge bushing supports the washer lid hinge pin and provides a smooth bearing surface. Replacing a worn bushing restores quiet, even lid movement and helps keep the lid properly aligned over time.

• Supports and centers the lid at the hinge
• Provides a low-friction bearing surface for the hinge pin/rod
• Helps reduce squeaking, looseness, and metal-on-metal wear
• Can help resolve a wobbly, misaligned, or scraping lid

• Disconnect power before servicing; support the lid to prevent dropping
• Remove the hinge pin/rod or screws as your model requires to access the bushing
• Pry out the worn bushing and press the new bushing fully into the hinge opening
• Reassemble and check lid operation; consider replacing the opposite-side bushing if worn

Mounted control board assembly that manages the appliance's electronic operations and user controls. Replaces a failed or damaged control board to help restore proper electronic control, user interface response, and normal cycle operation. What it does:

• Acts as the appliance's main electronic control, sending signals to motors, valves, heaters, and sensors.
• Replaces a faulty board that causes unresponsive controls, blank or error-filled displays, or failure to start cycles.
• Addresses intermittent operation or unexpected stops that trace to electronic control failures.
• Interfaces with the user control panel and system sensors to coordinate timed operations.

• Always disconnect electrical power (and water supply if applicable) before servicing the appliance.
• Handle the board by its edges and avoid touching contacts; use proper ESD precautions when available.
• Take photos of wiring and connector locations before removal to ensure correct reassembly.

This lid bumper cushions your washer lid where it meets the top panel, softening closure and protecting the finish. Replacing worn or missing bumpers reduces slamming and rattles for a quieter, smoother close.

• Cushions contact between the lid and top panel to reduce slamming noise
• Protects painted/enamel surfaces from chips and scratches at contact points
• Helps the lid sit level and minimizes vibration or rattling
• Replace if the bumper is missing, cracked, flattened, or hardened

• Disconnect power to the washer before servicing.
• Open the lid and locate the bumper(s) at the front corners (on the lid underside or top panel lip).
• Pull the old bumper straight out; clean the mounting hole.
• Press the new bumper firmly into the hole until fully seated and flush; test lid closure.

This leveling leg threads into the base of your washer to set height and keep the cabinet stable on uneven floors. Replacing worn or missing legs reduces vibration, walking, and noise for smoother, safer operation.

• Provides an adjustable foot to level and support the washer
• Helps reduce vibration, rocking, and "walking" during spin
• Replaces stripped, cracked, or missing leveling feet
• Helps with excessive shaking, rattling noises, or out-of-balance conditions

• Disconnect power and water; pull the washer forward for access.
• Support the appliance to prevent tipping; unscrew the old leg by hand or with pliers.
• Thread the new leg into the base; adjust all feet until level front-to-back and side-to-side.
• Ensure each foot contacts the floor firmly and the cabinet is stable before use.

This is the drain solenoid housing for a dishwasher. It secures and aligns the drain solenoid on the pump assembly so the drain valve actuates consistently and the tub can empty at the right time.

• Positions and insulates the drain solenoid on the pump/drain mechanism
• Maintains proper alignment for reliable drain-valve actuation
• Common symptoms of a failed housing: won't drain or drains intermittently
• May present as loud humming from the solenoid or visible cracks/heat damage on the housing

• Disconnect power and water supply before servicing
• Access the pump area beneath the tub; note solenoid, lever, and linkage orientation
• Transfer the existing solenoid and any clips/brackets to the new housing; reuse fasteners
• Run a short cycle to ensure proper draining after reassembly

A replacement pulsator (wash plate) that moves water and clothing during the wash cycle to maintain agitation and even cleaning. Installs at the tub hub and works with the factory retaining fastener to restore proper water flow. What it does

• Directs water flow and clothing movement to create agitation for effective washing.
• Restores even water circulation when fins are cracked, broken, or worn.
• Common symptoms indicating replacement: visible cracks or missing fins, loud or unusual noise during agitation, poor cleaning or clothes tangling.
• Designed to fit the washer tub hub and work with the original retaining hardware.

• Disconnect power and shut off the water supply before beginning any repair.
• Removal typically requires taking off the agitator/trim and the pulsator retaining fastener—follow the washer's service manual for exact steps.
• Inspect the hub, splines and retaining hardware; replace any damaged fasteners or seals to ensure a secure fit.

This machine screw secures panels, brackets, and internal components in compatible washers. Replacing a missing or stripped fastener restores a tight fit to help reduce vibration and keep parts properly aligned.

• 10-32 thread; 5/8-inch length; Torx T25 drive
• Fastens components and panels to resist loosening from vibration
• Replaces lost, corroded, or stripped screws
• Helps address loose or rattling panels, misalignment, or hardware that won't tighten

• Unplug the appliance and turn off water supply before servicing
• Use a T25 Torx driver; start threads by hand to avoid cross-threading
• Tighten snugly; do not overtighten
• Repair or replace the bracket/panel for a secure hold

This tub assembly replaces a cracked or leaking wash tub to restore proper water containment and drum support for your washer, helping reduce leaks, rubbing noises, and abnormal vibration during cycles. What it does:

• Provides the sealed reservoir that holds wash water and supports the inner drum during wash and spin cycles
• Helps stop or reduce water leaks caused by cracked or damaged tubs
• Can resolve rubbing, scraping, or thumping noises from a warped or broken tub
• Helps stabilize the drum to reduce vibration and improve spin performance

• Disconnect power and shut off water supply before starting; wear gloves and eye protection
• Tub assemblies are heavy and bulky—use two people or appropriate lifting equipment
• Follow the washer OEM service manual for disassembly, seal transfer/replacement, and torque specifications
• If bearings, seals, or mounting hardware show wear, replace them per OEM guidance for a complete repair

Transmission drive pulley nut.

Includes 12 washers.

This overload protector is a thermal motor protector that cuts power if the dryer motor overheats, helping prevent motor damage and unsafe operation. Replace a failed unit to restore the motor's built-in overheating protection. What it does:

• Senses excessive motor temperature and interrupts motor power to prevent damage.
• Common symptom: dryer may not start or the motor hums but won't turn when the overload has failed.
• Helps stop repeated motor overheating and can prevent associated electrical faults.
• Works as the motor's thermal safety device; must be replaced if open or damaged.

• Disconnect power to the appliance before servicing to avoid shock or injury.
• Transfer wiring and mounting exactly as removed; do not bypass the protector.
• Inspect motor and blower for obstructions or causes of overheating before reassembly.

This small bushing fits the washer's lid hinge to provide a smooth, stable pivot. Replacing a worn hinge bushing restores proper lid alignment and helps reduce squeaks, rubbing, or excessive play when opening and closing the lid. What it does:

• Acts as a low-friction sleeve between the hinge pin and bracket
• Supports smooth lid movement and helps maintain alignment
• Reduces metal-on-metal wear and hinge noise
• Symptoms of wear can include squeaking, binding, scraping, or a loose/wobbly lid

• 1 hinge bushing

• Disconnect power before servicing
• Support the lid to prevent it from dropping when the hinge is loosened
• Remove hinge hardware to access and swap the bushing; reassemble and check lid alignment
• Many models use a bushing on each hinge—inspect both sides and replace as needed