Wd-10485Tp Parts

A replacement lid assembly that restores the washer's top enclosure, helping keep laundry inside the tub and allowing the lid to open and close smoothly. Designed as a one-piece top lid for safe, reliable operation. What it does

• Replaces a cracked, bent or broken top lid so you can safely load and unload the washer.
• Restores proper lid alignment and sealing at the cabinet top to reduce splashing and contain water.
• Ensures the lid closes fully for normal machine operation and safety-interlock function.
• Improves appearance by replacing a worn or damaged top cover.

• One lid assembly.

• Disconnect power and water supply before beginning any work.
• Basic hand tools are typically required; some models may require removing the control panel or hinges.
• Handle carefully to avoid scratching or chipping the finish; two people may be helpful for alignment.
• If the washer has an electronic lid switch, verify switch engagement after installation.

This power cord assembly supplies mains power to the appliance, replacing a damaged or worn cord to restore safe electrical connection. It provides the appliance's primary power connection for normal operation. What it does:

• Carries household mains voltage to the appliance so it can power on and run
• Replaces frayed, cut, or heat-damaged cords that can cause intermittent power or arcing
• Restores a secure connection if the original cord or strain relief is damaged
• Helps prevent electrical hazards from exposed wires or loose connections

• One power cord assembly as shown

• Always disconnect the appliance from power before replacing the cord
• Inspect the terminal block and strain relief; install the cord with the same routing and secure the strain relief
• Ensure wire connections are tight and the grounding conductor is connected per local electrical code

This bellows is the flexible rubber door boot seal that creates a watertight barrier between the washer door and tub, helping prevent leaks and keeping laundry contained during cycles. What it does:

• Seals the front-load door opening to stop water from escaping during wash and spin cycles
• Helps prevent leaks that can cause water on the floor or under the machine
• Keeps lint, soil and moisture inside the drum, reducing musty smells
• Restores a damaged, torn or hardened boot to proper sealing performance

• One bellows

• Disconnect power and water supply before starting any repair
• Drain remaining water from the tub to avoid spills when removing the old boot
• Removing the door trim and spring clamp may be required; keep track of all fasteners

This top cover is a direct-replacement cabinet panel that restores the appliance's exterior finish and protects internal components from dust and damage. It helps maintain a safe, finished appearance and prevents debris from entering the chassis. What it does:

• Covers and protects internal components located at the appliance top
• Restores a smooth, finished exterior surface after damage or corrosion
• Eliminates gaps that can collect dust, lint, or liquids
• Helps prevent sharp edges and reduces risk of contact with internal parts

• One replacement top cover

• Disconnect power (and water, if applicable) before beginning work
• Remove trim or access panels as needed to reach mounting screws
• Support the cabinet while removing/installing the cover to avoid dropping or bending

This Top Cover is the outer cabinet panel that fits over the appliance's upper section to protect internal components and restore a finished appearance. It keeps controls and wiring covered while improving the unit's look. What it does:

• Covers and protects control components and wiring from dirt, spills, and accidental contact
• Restores a flush, finished appearance when the original top is dented, cracked, or missing
• Helps reduce airflow into the cabinet area to prevent debris buildup
• Provides a secure mounting surface for control assemblies and trim pieces

• Disconnect power (unplug or shut off breaker) before beginning any service
• Typical installation requires removing a few fasteners and lifting the old cover off; keep track of screws and clips
• Handle edges carefully to avoid cuts and protect painted surfaces from scratches
• Refer to your model's service manual or parts diagram for fastener locations and any bracket reassembly steps

This top cover replaces the appliance's upper exterior panel to restore appearance and protect internal components from dust and debris. It fits over the cabinet opening and provides a finished, serviceable surface. What it does:

• Replaces a dented, cracked, or missing top panel to restore the cabinet's appearance
• Protects internal parts and wiring from loose debris and moisture intrusion
• Eliminates rattles or movement caused by a warped or damaged top
• Provides the mounting surface for control consoles or trim

• One top cover panel

• Disconnect power (and gas supply if applicable) before starting any repair
• Typical installation requires removing screws and lifting the old top off; two-person lift may be needed for larger models
• Keep fasteners and trim in order; reuse original screws unless damaged
• If electrical components are attached to the top, disconnect wiring harnesses carefully and note routing before reassembly

This replacement refrigerator door handle restores a secure grip for opening and closing the appliance, improving usability and appearance after a broken, cracked, or missing handle. What it does

• Replaces a damaged or missing refrigerator door handle so you can open and close the door reliably
• Provides a solid, ergonomic grip for normal daily use
• Restores the cabinet's finished look when original handle is cracked, loose, or chipped
• Matches the original mounting style to align with the door and latch mechanisms

• One replacement door handle

• Turn off power to the appliance and/or unplug before starting if work requires tilting or removing panels
• Use basic hand tools; follow OEM diagram for screw locations and orientation
• Keep removed screws and trim pieces for reinstallation; do not overtighten fasteners