Wed9720xw2 Parts

This cover mounts inside the dryer and shields the drum light from direct contact with tumbling clothes. It helps protect the light bulb and prevents garments from snagging on the light assembly. Replace this cover if it is cracked, melted, missing, or if clothes are catching near the light area during drying cycles.

This replacement washer is a small hardware component used in appliance assemblies to provide a stable bearing surface and proper spacing. Replacing a worn or missing washer helps maintain alignment, reduce vibration, and protect mating parts from damage.

• Distributes load under a nut, bolt, pin, or shaft to protect mating surfaces
• Maintains correct spacing and alignment within stacked components
• Helps reduce friction, vibration, and noise in moving assemblies
• Worn or missing washers can contribute to looseness, wobble, rattling, or premature wear

• Disconnect power and shut off gas/water before servicing
• Note the original order and orientation of parts during disassembly
• Inspect fasteners, shafts, and bushings; replace any that show wear or damage
• Tighten fasteners securely per the service manual; do not overtighten

Dryer drum support pad provides cushioning and reduces noise during operation. Replace if worn, cracked, or causing rattling sounds. Confirm fit with your model.

This metal clamp secures the drive motor to its mounting bracket inside the dryer. It prevents the motor from shifting or vibrating during operation. Replace this clamp if it is bent, broken, or missing, which can cause excessive vibration, unusual noises, or a motor that moves out of position.

Relocates your dryer's exhaust vent from rear to left, right, or bottom. Includes elbows, duct, and instructions. Replace when changing installation.

Dryer won't start or stops mid-cycle? A broken door strike prevents the latch from catching, so the control can't detect a closed door. Simple fix.

This factory fastener secures appliance components such as panels, brackets, and handles. Replacing a missing or damaged screw restores a tight fit, reduces rattles, and helps keep parts aligned for smooth, reliable operation.

• Secures components to the appliance frame or assemblies
• Helps maintain alignment and structural stability
• Replaces missing, rusted, or stripped hardware
• Common symptoms include loose/wobbly handles or panels, rattling/vibration noises, or a visibly missing screw

• Disconnect power before servicing
• Use the correct driver/bit and start threads by hand to avoid cross-threading
• Do not overtighten; snug until secure
• Replace any that are corroded or stripped for an even hold

Replacement screw secures panels, brackets, and internal assemblies. Needed when original hardware is stripped, corroded, or missing to keep parts tight.

The Screw is an OEM component compatible with Whirlpool washing machines. This screw secures the rear panel onto the cabinet frame, ensuring a sturdy connection between housing components.  Proper installation is critical for the washer's structural integrity.

Causes of a bad screw include corrosion from repeated water exposure or stresses from years of use. Loosening can occur from vibrations weakening the threads over time. 

Symptoms of a bad screw include:

• Rear panel detaching from frame opening gaps
• Increased noise and vibrations from a compromised seal  
• Stress on other connections from improper mounting points
• Potential leak paths from openings near hoses or tub areas

This OEM Whirlpool replacement screw helps maintain a tight panel closure. It is compatible with additional brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Dryer lint screen door provides access to the lint filter. Replace if cracked, broken, or won't close properly. Verify fit with your model number.

This metal retaining clip secures components or trim in place within your appliance. Replacing a damaged or missing clip restores a snug fit, prevents rattles, and helps keep panels and parts properly aligned.

• Provides spring tension to hold mating parts or panels in position
• Helps maintain alignment and reduce vibration-related noise
• Restores retention when the original clip is bent, fatigued, or lost
• Typical symptoms: loose or sagging trim/panel, buzzing/rattling noises, parts not staying seated

• Disconnect power before servicing; allow hot surfaces to cool
• Wear cut-resistant gloves—clip and sheet-metal edges can be sharp
• Note the clip's orientation before removal; take a reference photo
• Use needle-nose pliers to release/install; avoid over-bending the clip

This is the plastic or metal housing that surrounds the blower wheel inside the dryer, forming the chamber that directs exhaust air from the drum toward the vent outlet. It creates the sealed pathway necessary for proper airflow during drying cycles. Replace this housing if it is cracked, warped, or damaged, which can cause poor drying performance, unusual noises, or lint buildup due to air leaks.

Secures the heater housing to the dryer cabinet. Replace if your bracket is bent, cracked, or missing to restore stable mounting and alignment.

Chrome finish cabinet top panel for dryers. Replaces dented, bent, or rusted top panels to restore clean appearance and secure fit over internal components.

Color: Black. Size: 12 oz. Acrylic appliance aerosol can spray paint.

Vent adapter kit connects your dryer's blower outlet to exterior ductwork. Replace if your current adapter is cracked, broken, or missing for proper venting.