Wfc31050ab0 Parts

Color: Biscuit.

This 10-32 terminal block nut fastens wire lugs to the appliance's terminal studs. Replacing a missing, stripped, or corroded nut restores a tight, reliable connection and helps prevent heat damage or intermittent power at the connection.

• Secures wire lugs to a 10-32 terminal stud for a solid electrical connection
• Restores proper clamping force when the original nut is stripped, corroded, or missing
• Helps address loose/burned terminal connections, heat discoloration, or intermittent power at the block
• Suitable for terminal block and similar 10-32 stud applications on compatible appliances

• Disconnect power at the breaker or unplug the appliance before servicing
• Inspect the terminal block, studs, and wiring for heat damage; replace any damaged components
• Clean threads and start the nut by hand to avoid cross-threading; tighten firmly without overtightening
• If the stud turns while tightening, hold it with an appropriate tool to protect the block

Bottle with brush. Color: Biscuit paint. It's point-six fluid ounces.

This replacement surface burner control knob restores smooth, accurate control of your range or cooktop. Replace cracked, stripped, or missing knobs so you can reliably turn burners on/off and adjust heat to the desired setting.

• Attaches to the valve or switch shaft to power the surface burner on/off and set the heat level
• Replaces knobs that are cracked, stripped, loose, or missing
• Restores proper indexing so Off/Low/High markings align correctly
• Common symptoms include a knob that spins freely, wobbles, falls off, or won't engage the stem

• Allow all cooking surfaces to cool and turn controls off; disconnect power if servicing near internal controls
• Pull the old knob straight off the stem—avoid prying tools that could damage surrounding trim
• Align the new knob with the shaft (match the flat/D-shape) and press straight on until fully seated

This cooktop support rod props the range top open during cleaning or service, preventing accidental slams. Replace a bent or missing rod to keep the cooktop safely supported while you access surface components.

• Supports the lift-up cooktop in the open position
• Helps prevent the cooktop from dropping unexpectedly
• Provides safer access to burners, igniters, and valves for cleaning or repair
• Common signs of failure: top won't stay up, rod is bent, loose, or missing

• Disconnect power and shut off gas; allow the appliance to cool completely
• Lift and support the cooktop; note the rod's orientation and pivot points
• Disengage the old rod from its brackets and install the replacement securely
• The rod holds the cooktop open before closing

This door-activated switch detects when the oven door opens or closes and signals the appliance to control the interior light. Replacing a worn or failed switch restores dependable light operation and accurate door-status feedback.

• Senses oven door position and opens/closes the light circuit
• Controls the oven's interior light based on door position
• Provides door-status input to the control for normal operation
• Typical symptoms: light stays on, won't turn on, or flickers with door movement; door-ajar messages may appear

• Disconnect power at the breaker or unplug the unit before servicing
• Access the switch from behind the front frame or control area, depending on model
• Move wires to the new switch one at a time to maintain correct positions; secure with existing hardware
• Restore power and verify light operation with door open/closed before reassembly

This replacement terminal block cover encloses the appliance's incoming power connections. It protects the wire terminals from accidental contact and debris, restoring a safe, finished connection area when the original cover is damaged or missing. What it does:

• Covers and shields the power terminal block where the supply wires connect
• Helps prevent accidental contact with live electrical connections
• Helps keep dust and debris out of the connection area
• Common signs: missing or broken cover, cover won't stay attached, visible heat damage or discoloration on the original cover

• One terminal block cover

• Disconnect power at the breaker or unplug the appliance before servicing
• Access the terminal block per your model's service information
• Reuse existing mounting hardware; position and secure the new cover without pinching wires
• Inspect wires/terminals for heat damage or looseness and correct before reassembly

This support bracket secures an appliance cabinet component or mounting point to restore alignment and reduce movement. It replaces worn or broken supports so panels and internal parts stay properly positioned during normal operation. What it does

• Holds a cabinet panel, frame, or internal component in place to maintain proper alignment.
• Stabilizes mounting points to help reduce vibration, rubbing, or intermittent noise.
• Common replacement when you notice a loose or sagging panel, rattling, or unusual chassis movement.
• Provides a direct mechanical fix—matches the OEM bracket design and fit.

• Disconnect power (and shut off gas supply for gas appliances) before starting any repair.
• Remove necessary panels and fasteners to access the old bracket; keep track of all screws and clips.
• Compare the new bracket to the old part for orientation before installing; secure using the original fasteners—do not overtighten.

This frame surrounds and supports the window glass in your oven door, keeping the glass secure and aligned. Replace a bent or corroded frame to address loose glass and restore the door's proper fit and clean appearance.

• Secures the oven door window glass within the door assembly
• Helps maintain alignment and seal around the window area
• Replaces frames that are bent, cracked, or corroded
• Addresses loose, rattling, or misaligned door glass
• Restores the finished look of the door

• Disconnect power and allow the oven to cool completely before service
• Remove the door per your model's instructions and place it on a padded surface
• Handle glass with cut-resistant gloves; keep track of screws, clips, and insulation for transfer
• Seat the glass evenly and avoid overtightening fasteners during reassembly

This vent trim is the finishing piece that frames the vent opening and directs airflow. Replace a cracked, warped, or missing trim to restore a secure fit and a clean, factory look at the vent area.

• Covers and finishes the vent opening for a clean appearance
• Helps guide exhaust air/steam away from the cabinet as designed
• Replaces broken tabs, cracks, discoloration, or a missing trim piece
• Can reduce rattling or vibration from a loose or damaged vent surround

• Disconnect power before servicing
• Access the vent area and remove screws or clips securing the old trim
• Reuse existing mounting hardware; align and tighten evenly without overtightening
• Handle carefully to avoid scratching or cracking the new trim

Mounting bracket that secures a drawer to its cabinet or glide assembly, restoring stability and alignment for smooth opening and closing. Replaces damaged or missing brackets that cause sagging, misalignment, or detachment. What it does:

• Secures the drawer to the cabinet or slide hardware so the drawer stays aligned and supported.
• Restores smooth opening and closing when a worn or broken bracket causes binding or uneven travel.
• Prevents the drawer from sagging, pulling out, or detaching from the glide.
• Use when bracket is cracked, bent, or missing to regain proper drawer function.

• Disconnect power to the appliance or unplug it before beginning work.
• Basic hand tools are typically required; keep original fasteners for reuse if they are undamaged.
• Remove the drawer and inspect the glide/rail for damage before installing; reinstall drawer and verify smooth operation.

Color: White. Size: 2 oz. can. Porcelain touch-up paint.

This broiler pan restores a sturdy broiling surface in your oven. It holds food for high-heat broiling while the lower tray catches drippings to help reduce smoke and keep the oven cavity cleaner.

• Provides a durable surface for broiling under the broil element or flame
• Collects grease and juices beneath the food during high-heat cooking
• Replaces pans that are missing, warped, chipped, or heavily rusted
• Helps cut down on smoke and mess from burnt-on residue on a damaged pan

• Allow the oven to cool completely before handling
• Slide the pan onto the appropriate rack position per your model's instructions; no tools required
• Use oven mitts—surfaces and edges can be hot after broiling
• If your model uses a separate broiler grid or rack, position it on top of the pan before cooking

Utility drawer assembly replaces a damaged or missing storage drawer, restoring tidy storage and proper sliding action in the appliance. Durable replacement designed to match the original fit and function. What it does:

• Provides a dedicated storage compartment for small items and accessories inside the appliance
• Restores proper drawer alignment and smooth sliding operation
• Replaces cracked, broken or missing drawers and mounting tabs that allow the drawer to fall out or not seat correctly
• Helps prevent items from shifting or falling into the appliance interior

• Always disconnect power to the appliance before beginning service and follow basic safety precautions
• Removal typically involves sliding out the old drawer and lifting or releasing retention tabs; installation is the reverse
• Inspect mounting rails/tabs for damage during replacement; damaged hardware may require separate parts

This electronic control board is the brain of the appliance, directing cycles and powering key components. Replacing a failed board helps restore proper operation, reliable starts, and accurate cycle sequencing. What it does:

• Coordinates inputs from sensors and the user interface to control programmed functions
• Sends power to motors, pumps, fans, valves, and heaters as needed
• Manages cycle timing and safety checks
• Common symptoms include: won't power on or start, won't advance/complete, stops mid-cycle, erratic operation, or error codes

• 1 electronic control board

• Disconnect power at the breaker or unplug before servicing
• Use ESD protection; handle the board by the edges to avoid static damage
• Move connectors one at a time from the old board to the new board; each is fully seated
• Secure the board in its housing/bracket, reassemble, and run a test/diagnostic cycle if available

Qty 4 needed to complete full insulation