Wfw9500 Two1 Parts

This water level pressure switch senses tub water level and signals the control to stop filling and advance the cycle. Replacing a failed switch restores proper fill shut-off and allows the washer to move to wash, drain, and spin.

• Detects water level via air pressure in the attached hose from the tub air dome
• Signals the timer/control to close inlet valves at the selected fill level
• Enables agitation and spin only when the level is appropriate or the tub is empty
• Typical symptoms of a failed switch include overfilling or underfilling, continuous filling, cycle not advancing, or no spin

• Disconnect power and turn off water supply before servicing
• Access the switch in the control console or top panel; note wire locations for reassembly
• Transfer the pressure hose and wire connectors to the new switch one at a time; ensure the hose is clear, not kinked or cracked, and fits snugly
• After installation, run a quick fill test to ensure proper shut-off and cycle progression

Includes all four shipping bolts.

This 2-pack of dryer vent clamps secures the vent hose to the dryer outlet and the wall/vent hood. A tight connection helps maintain airflow, reduce lint leaks, and keep the duct from slipping off during use.

• Tightens around the vent hose to hold it securely to the dryer exhaust collar or exterior vent
• Helps prevent hose detachment, air leaks, and lint escaping at the connection
• Supports proper exhaust airflow by keeping connections sealed and stable
• Common symptoms pointing to replacement: hose won't stay on, visible gaps or lint around fittings, rattling at the vent, or longer dry times from poor ventilation

• Disconnect power; for gas dryers, shut off gas supply before moving the appliance
• Slide a clamp over the hose, seat the hose fully on the collar, position clamp over the fitting, and tighten with a screwdriver or nut driver
• Do not overtighten; avoid crushing thin foil ducting; ensure the hose is straight and not kinked
• Restore power and verify strong airflow at the exterior exhaust

Includes 2 adhesive pads, 2 brackets, 4 screws, and installation instructions.

This factory fastener secures appliance components such as panels, brackets, and covers. Replacing a missing, stripped, or rusted screw restores a tight fit and helps reduce vibration, rattling, and shifting during operation.

• Fastens metal or plastic parts to the appliance cabinet/frame
• Helps maintain proper alignment and reduces noise from loose panels
• Replaces hardware that is missing, corroded, or with stripped threads
• Symptoms include rattling, looseness, gaps, or misaligned parts

• Disconnect power; shut off gas/water before servicing
• Support panels to prevent drops; watch for sharp edges
• Start threads by hand to avoid cross-threading; use the correct driver
• Do not overtighten; match the original screw's location and orientation

This bracket secures a component or panel inside your appliance, keeping it properly aligned and stable during operation. Replacing a bent, cracked, or missing bracket restores solid mounting and helps prevent vibration and further damage.

• Provides a rigid mounting point for a specific component or panel
• Maintains proper alignment for reliable fit and function
• Replaces damaged, deformed, or missing bracket hardware
• Typical symptoms include loose or rattling parts, misaligned panels, vibration, or components shifting out of place

• Disconnect power (and shut off water or gas, if applicable) before servicing
• Note the original bracket's orientation; transfer any reusable hardware to the new bracket
• Use existing or manufacturer-specified screws; tighten securely without over-torquing
• Verify component alignment and clearances before restoring power/service

This replacement screw secures appliance components and panels so they stay aligned and rattle-free during operation. Replace stripped, missing, or corroded hardware to restore a tight fit and dependable performance. What it does

• Fastens brackets, panels, and internal sub-assemblies in the appliance
• Helps maintain alignment to reduce vibration and rattling
• Replaces missing, rusted, or stripped screws that no longer hold
• Useful when a part won't mount securely or a screw backs out during use

• One screw

• Disconnect power; for gas appliances, also shut off the gas supply
• Compare to the original for length and thread style for the location
• Start threads by hand to avoid cross-threading; use the correct driver bit
• Do not overtighten; if the mounting hole or clip is worn, replace it

This hose clamp secures a rubber or plastic hose to its fitting to maintain a tight, leak-resistant seal. Replace a worn or missing clamp to stop drips and keep appliance water connections secure.

• Fastens a hose to a barb or port to prevent leaks
• Helps keep hoses from slipping off due to vibration or pressure
• Restores proper sealing when a clamp is rusted, bent, or stripped
• Common symptoms: water dripping at a hose joint, loose hose connection, or a clamp that won't tighten

• Disconnect power and shut off the water supply before servicing
• Place a towel to catch residual water when removing hoses
• Position the clamp just behind the hose barb/bead and secure with the appropriate tool
• Restore water and power, then run a quick check for leaks at the connection

This Dispenser Divider installs in the washer's detergent drawer to separate and control liquid or powder detergent in the main-wash compartment. Replacing a worn or missing divider helps restore proper dispensing and more consistent cleaning results.

• Sits in the main-wash section to select liquid or powder detergent
• Directs and regulates water flow for complete detergent siphoning at the right time
• Replaces a cracked, warped, or missing divider that can affect wash performance

• Disconnect power and turn off water supply before servicing
• Pull the dispenser drawer out and depress the release tab to remove it
• Lift out the old divider, clean the compartment, and snap the new divider in the correct orientation (liquid or powder as marked)
• Reinstall the drawer and run a short cycle to verify proper dispensing

This hose clamp secures a flexible hose to its fitting to help prevent leaks and hose blow-offs during operation. Replace a rusted, stripped, or distorted clamp to restore a tight, reliable seal at the connection point.

• Applies clamping force around a hose to hold it on a barb or stub fitting
• Commonly used on washer drain and tub-to-pump hose connections
• Helps stop drips at the joint and prevents the hose from slipping off
• Typical failure signs: leaking at the connection, clamp won't tighten, visible rust, broken/warped band

• Unplug the appliance and turn off water supply; expect some residual water
• Seat the hose fully on the fitting; place the clamp just behind the bead/barb
• Tighten until snug and secure; do not overtighten to avoid damaging the hose
• Run a short test cycle and recheck for leaks at the connection

Extends the drain hose approximately 4 feet. You must also order a drain hose connector kit: 285835.

This front counterweight mounts to the washer's outer tub to help balance and stabilize the drum during spin. Replacing a damaged weight can reduce vibration and noise and help prevent the machine from walking. What it does:

• Adds mass at the front of the tub to counterbalance loads during spin
• Helps control vibration, shaking, and banging noises
• Can resolve out-of-balance interruptions or excessive movement
• Visible cracks or broken mounting ears indicate the weight needs replacement

• One front counterweight

• Disconnect power and water; use proper lifting techniques—this part is heavy
• Support the tub and remove front cabinet components/door boot as needed for access
• Remove and retain mounting bolts; tighten bolts evenly when reinstalling
• Inspect mounting points and suspension components while accessible; replace if worn

This L-shaped flowmeter hose is part of the washer's water inlet circuit. It routes water through the flow sensor and maintains a tight, leak-free connection, helping the machine fill accurately and operate as designed.

• Channels incoming water through the flowmeter for correct fill measurement
• Maintains a secure, leak-resistant connection within the fill system
• Typical failure signs: water dripping during fill, visible cracking/hardening, loose fit, or kinks restricting flow
• A damaged or leaking hose can contribute to inaccurate fill sensing or fill-related errors

• Disconnect power and shut off both water supplies before servicing
• Note routing/orientation; transfer existing clamps or install new ones if needed
• Fully seat hose on each fitting and secure clamps without over-tightening
• Restore water and power, then run a fill to check all connections for leaks

This replacement ball is the small spherical component used in select Whirlpool-built mechanisms. It acts as a moving seal or detent to control flow or position, restoring smooth, reliable operation when the original ball is worn or missing. What it does:

• Provides the sealing or detent action within its valve, hinge, or track assembly
• Helps prevent backflow, leaks, or unwanted movement
• Restores smooth operation when mechanisms feel rough, bind, or won't stay in position
• Replace if the original is deformed, pitted, corroded, or missing

• 1 ball

• Disconnect power and shut off water supply if applicable
• Access the specific assembly per your model's service documentation and note part order
• Place the ball in its seat/track with any companion spring or seal as designed
• Inspect mating surfaces and related seals or springs and replace if worn

This dishwasher door latch lever links the handle to the latch and safety switches so the door can secure closed and the cycle can start. Replacing a cracked or worn lever restores reliable latching and starts. What it does:

• Transfers handle movement to the latch mechanism and door switches
• Helps the control recognize a fully closed door so the dishwasher will run
• Contributes to keeping the door securely closed during operation
• Resolves: cycle won't start, door won't latch or stay closed, need to hold door to run, loose/floppy handle feel

• 1 lever

• Disconnect power at the breaker before servicing the door
• Open the door and remove inner door panel screws to access the latch/handle area
• Note the original lever's orientation; move any springs/clips to the new lever and seat it fully in the pivot
• Reassemble, verify smooth handle action, and ensure the door latches and a cycle initiates

This Marquardt ground switch completes the appliance's ground connection so controls and safety systems have a proper reference. Replace a failed ground switch to restore reliable grounding and help eliminate related electrical faults. What it does:

• Provides the ground connection path used by controls and safety circuits.
• Replaced when continuity tests fail or when appliances have intermittent power, control errors, or nuisance breaker trips.
• Restores correct electrical grounding to help reduce fault conditions and erratic control behavior.
• Matches the original switch form and electrical connector layout for a direct replacement.

• Disconnect all power (unplug appliance and/or shut off breaker) before beginning service.
• Photograph or label wiring and connector positions before removal; transfer connectors to the new switch exactly.
• Inspect connectors and wiring for damage; replace any frayed or heat-damaged wiring.