Wgd86hebw1 Parts

The PAD is an OEM part crafted specifically for Whirlpool dryers. This pad plays a crucial role in the dryer's operation by providing support and cushioning for the dryer drum. Its precise design and compatibility ensure proper fitting and reduce noise during the drying cycles, contributing to smoother operation.

A worn-out or damaged dryer pad can lead to disruptions in the dryer's performance. Causes of a faulty pad might include wear over time, physical damage, or exposure to high heat, resulting in increased noise or imbalance during operation.

Symptoms of a bad PAD may include:

• Unusual or increased noise during dryer operation
• Visible signs of wear or deterioration on the pad
• Drum imbalance or wobbling during use

This is a genuine Whirlpool OEM replacement this part is also compatible with Maytag, Jenn-Air, and some Kenmore models.

The Screw is an OEM component compatible with Whirlpool washing machines. This screw secures the rear panel onto the cabinet frame, ensuring a sturdy connection between housing components.  Proper installation is critical for the washer's structural integrity.

Causes of a bad screw include corrosion from repeated water exposure or stresses from years of use. Loosening can occur from vibrations weakening the threads over time. 

Symptoms of a bad screw include:

• Rear panel detaching from frame opening gaps
• Increased noise and vibrations from a compromised seal  
• Stress on other connections from improper mounting points
• Potential leak paths from openings near hoses or tub areas

This OEM Whirlpool replacement screw helps maintain a tight panel closure. It is compatible with additional brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This strike is the latch receiver the door or lid engages when closed. Replacing a worn or broken strike restores a secure close and ensures the control correctly senses a closed door so cycles can run. What it does:

• Provides the fixed catch point for the latch mechanism
• Keeps the door/lid closed and properly aligned during operation
• Works with the interlock/switch to signal that the door/lid is closed
• Common symptoms: door won't latch or pops open, "door/lid open" message, cycle won't start, visible damage to the strike

• 1 strike

• Disconnect electrical power to the appliance; shut off water if applicable
• Open the door/lid and remove the original strike (typically secured by screws or retaining tabs)
• Position and secure the new strike, reusing original hardware; tighten snugly without over-tightening
• Close and open the door/lid to confirm smooth latch engagement and alignment; adjust if needed

This small plug seals and finishes an unused factory or service hole on the appliance cabinet or liner. It restores a clean, finished appearance and helps keep dust and splashes out of the opening. What it does

• Closes an open hole on the cabinet/liner or panel
• Helps reduce entry of debris and incidental moisture into the opening
• Maintains a neat, finished look
• Replace if the original plug is missing, cracked, or won't stay seated

• 1 plug

• Disconnect power before servicing; shut off water supply if working near water lines
• Identify the correct opening per your model's parts diagram
• Remove any remnants of the old plug; clean the area
• Align and press the plug fully into the hole until it sits flush—do not force or deform the panel

This is the appliance's cabinet top panel in a chrome finish. It replaces a dented, bent, or rusted top to restore a clean appearance and a secure fit while protecting internal components and supporting mounted parts.

• Forms the finished top surface of the cabinet (chrome finish)
• Shields internal components from debris and accidental contact
• Provides mounting/support points for the console, hinges, or brackets (varies by model)
• Addresses damage, corrosion, looseness, or rattling from a bent or missing top

• Disconnect power before servicing; wear cut-resistant gloves (sheet-metal edges are sharp)
• Retain and reuse the original screws/clips; transfer any brackets from the old panel
• Fasteners are typically at the rear or beneath the console—support the panel, remove screws, then lift off
• Align the new panel and tighten fasteners evenly to ensure a secure, rattle-free fit

Color: Gray. Size: 13 oz. can. Used for coating the dryer drum interior. Acrylic appliance paint.

Console shell replaces the dryer's outer control housing to restore a clean, secure surface for the control assembly and controls. It repairs cosmetic damage while providing the proper mounting surface for the control components. What it does:

• Covers and protects the control assembly from impact, dust, and debris.
• Provides the structural mounting surface for knobs, switches and the control interface.
• Common symptoms it addresses: cracked, dented, warped or split console and loose or misaligned controls.
• Restores the dryer's appearance and helps prevent further damage to internal control components.

• Disconnect power (unplug the dryer or shut off the circuit breaker) before beginning any work.
• Removal/installation typically requires removing the dryer top or front panel; basic hand tools (screwdriver, nut driver) are commonly used.
• Handle any sharp sheet-metal edges with care and wear gloves and eye protection.

This hose kit replaces worn or damaged appliance hoses to restore proper water flow and prevent leaks. It's a direct-fit replacement for compatible Whirlpool systems and helps stop visible leaks and restore normal fill/drain operation. What it does

• Replaces cracked, split or leaking hoses to stop water loss and reduce risk of appliance damage
• Restores reliable water flow for filling and draining functions
• Helps eliminate poor draining, intermittent filling, or water pooling near the appliance
• Works with existing clamps and connections when installed correctly

• Disconnect power and shut off the water supply before starting any repair
• Inspect connection fittings and replace clamps if worn; ensure a snug, leak-free fit
• Route hoses without kinks and secure to avoid chafing or strain
• After installation, run a short cycle and check all connections for leaks

This exhaust cover plate protects and finishes the dryer's exhaust outlet, helping direct airflow and keeping the vent opening sealed from debris. It provides a clean, durable surface where the exhaust connects to the dryer cabinet. What it does:

• Covers and seals the dryer exhaust opening to prevent dust and lint buildup around the vent
• Helps direct exhaust airflow into the duct for proper ventilation
• Restores a finished appearance to the exhaust area after repair or replacement
• Can reduce drafts and discourage pests entering through the vent opening

• Disconnect power to the appliance before starting any work.
• Use basic hand tools; handle edges carefully to avoid cuts.
• Verify proper alignment with the exhaust opening and secure with the original screws or hardware.
• Inspect the exhaust duct and surrounding seals for wear.

This finished burner funnel directs gas and air into the burner for correct flame shape and ignition. It replaces a damaged or corroded funnel to help restore even heating and reliable burner performance. What it does:

• Channels gas and air into the burner for proper mixing and flame distribution
• Helps maintain even flame across the burner for consistent cooking heat
• Can reduce ignition delays or uneven flames caused by a damaged funnel
• Works with the burner assembly; not a standalone gas valve or igniter

• Turn off gas supply and electricity to the appliance before servicing
• Replace only with the correct funnel for your burner; follow OEM diagram for orientation
• Tighten fittings by hand-first, then snug—do not overtighten; inspect for leaks after reassembly

This blower housing assembly replaces the blower chamber that supports the blower wheel and routes air through the dryer for proper tumbling and drying. Restores correct airflow and helps reduce overheating or poor drying performance. What it does:

• Houses and supports the blower wheel to direct airflow from the drum to the exhaust.
• Ensures proper airflow for consistent drying and venting.
• Can address symptoms like weak airflow, long dry times, or unusual blower noise when damaged or cracked.
• Works with the blower wheel and motor to maintain lint passage and exhaust flow.

• Disconnect power before inspecting or replacing the blower housing; follow manufacturer safety procedures.
• Access may require removing the dryer front or rear panel depending on model.
• Inspect the blower wheel and motor for damage or obstructions while replacing the housing.

This genuine mounting screw secures panels and components so assemblies stay aligned and rattle-free. Designed to replace worn or missing fasteners and restore proper fit and function. What it does:

• Secures panels, brackets or trim to prevent movement and vibration
• Restores proper alignment of assemblies that feel loose or shift
• Helps eliminate rattling, squeaks, or parts that fall away during use
• Matches OEM thread and head type for correct fit

• Use the matching screwdriver or bit to avoid stripping the head
• Tighten until snug; do not overtighten which can strip threads or crack plastic
• Replace any additional damaged or missing fasteners for best results
• Disconnect power or follow appliance-specific safety steps before working near wiring or energized components

This bulkhead is the front structural panel that supports the dryer drum and seals the front of the cabinet to maintain proper airflow and drum alignment. Replacing a worn bulkhead restores stable drum rotation and prevents air leaks. What it does:

• Supports the drum and front bearing to keep the drum centered and turning smoothly
• Seals the front cabinet to direct exhaust airflow through the blower and vent
• Reduces rubbing and vibration caused by a damaged or warped bulkhead
• Helps eliminate airflow leaks that can extend dry times or cause overheating warnings

• One bulkhead

• Disconnect power (and gas supply if applicable) before any service
• Service typically requires removing the dryer front panel and drum for access
• Inspect and replace any worn gaskets, bearings, or fasteners while replacing the bulkhead

This touch-up paint restores small chips and scratches on painted appliance surfaces to improve appearance and slow corrosion. It's a simple cosmetic repair that helps appliances look cared-for between major services. What it does:

• Covers minor paint chips, nicks and surface scratches
• Helps restore a uniform finish on exterior panels and trim
• Reduces likelihood of surface rust where bare metal is exposed
• Ideal for spot repairs on visible areas without repainting large panels

• One touch-up paint item for appliance finish

• Work in a well-ventilated area and protect surrounding surfaces
• Shake well and test on an inconspicuous spot before applying
• Apply sparingly in thin coats; allow each coat to dry per product instructions
• Keep out of reach of children and away from open flame