Wm2hm101 Parts

Secures hose connections to maintain watertight seals in your washer. Replace if you notice leaks or loose hoses during operation. Verify fit with model number.

This washer shock absorber mounts between the outer tub and base to control movement during spin. Replacing a worn damper restores stability, reduces vibration and noise, and helps prevent the machine from walking or banging.

• Stabilizes the tub during spin by absorbing and controlling movement
• Reduces vibration and cabinet noise for smoother operation
• Helps the washer reach and maintain proper spin speed
• Worn shocks can cause shaking, banging, or walking during spin

• Disconnect power and water; use gloves and protect the floor.
• Access from the front or rear depending on model; remove panels as needed.
• Support the tub, then remove fasteners at both ends; install the new damper in the same orientation and tighten securely.
• Reassemble, level the washer, and run a test spin to check for vibration.

Seals the gap between washer tub and door opening to prevent leaks. Replace if torn, cracked, or deformed to restore watertight seal. Verify fit.

Replaces the front outer tub cover that houses the door boot seal and aligns the spin basket. Order a new cover if yours is cracked or worn from use.

Washer won't spin or shows LE error? A faulty stator assembly stops the motor from turning the drum. Moderate DIY repair restores spin and agitation.

Fix a blank, dim, or flickering display panel with this washer control board. Restores front-panel settings and status indicators when controls stop responding.

Secures rubber hoses to fittings with constant spring tension to prevent leaks. Replace when rusted or weakened to maintain a tight seal. Confirm fit.

The washer water inlet filter is a small mesh screen that sits at the water inlet valve connection point and catches sediment, debris, and mineral particles from your home's water supply before they enter the machine. Keeping this filter clear ensures proper water flow into the washer. Replace this part if your washer is filling slowly, not filling at all, or if the existing filter is torn, corroded, or too clogged to be cleaned effectively.

Fix washer leaks with this hose clamp. Secures hoses to pumps and valves, preventing water leaks and disconnections during wash cycles. Simple repair.

Shock absorber stabilizes the washer tub during operation. Replace if cracked, broken, or loose to control vibration. Mounts between tub and cabinet.

This Leg Adjusting Wrench is a simple tool used to turn and secure appliance leveling legs so washers and dryers sit flat and operate quietly. It makes adjusting legs faster and helps reduce rocking and vibration. What it does:

• Fits over standard appliance leveling legs to raise or lower each corner
• Helps stabilize machines to prevent rocking and uneven operation
• Reduces vibration and noise caused by unlevel appliances
• Useful when installing, moving, or re-leveling washers and dryers

• Turn legs slowly and adjust one corner at a time until the appliance sits level.
• Unplug the appliance (and shut off gas supply for gas dryers) before performing major moves or checks.
• Use caution to avoid pinching fingers when lowering legs; keep hands clear of pinch points.
• Check for damaged feet or mounting hardware and replace as needed.

This knob assembly replaces a worn or broken control knob so you can reliably set and adjust appliance settings. It restores a secure, easy-to-turn interface for the appliance's control shaft. What it does:

• Fits onto the control shaft to allow manual selection of settings and temperatures.
• Replaces cracked, stripped, or loose knobs that no longer grip the control shaft.
• Helps resolve issues where the control won't turn smoothly or slips while changing settings.
• Restores tactile feedback for accurate user control.

• Disconnect power to the appliance before removing or installing the knob.
• Pull the old knob straight off the control shaft.
• Align the knob's internal splines with the control shaft and push until fully seated.
• If knob does not seat or control still slips, inspect shaft splines and replace damaged components as needed.

Does not come with a hose or filter. These have to be purchased separately

Pivot hanger assembly that supports and stabilizes washer components. Replace if worn, damaged, or causing misalignment to restore smooth movement.

This replacement knob assembly restores tactile control for a range or cooktop control. It provides a secure grip and clear detent positions so you can set burner or surface settings reliably. What it does:

• Replaces a worn, cracked, or missing control knob to regain safe, predictable control
• Engages the shaft and detents so settings stay put during use
• Helps eliminate slipping or difficulty turning the control
• Matches original fit and function for direct replacement

• One knob assembly as shown

• Turn power/gas to the appliance off before servicing; follow appliance manufacturer safety instructions
• Remove the old knob by pulling straight off the control shaft; press the new knob onto the shaft until it seats
• Wear work gloves to protect hands from sharp edges during access

Fix water leaking from your washer dispenser or misdirected flow with this dispenser water guide channel. Routes water properly to prevent splashing.