Wmh2175xvs-5 Parts

Very easy fix. Unplugged microwave, then lowered bottom panel, removed the two leads to the turntable motor, removed two screws attached to motor, removed old motor, put new spacer on motor stem, installed motor with same two screws, reattached the two wires, reattached panel ( after cleaning all the grease that built up over the last 6 years), plugged microwave in and good as new! Took me twenty minutes. Note: the two screws holding the motor were not Phillips like those holding the panel. So... Read more

Bought a new home with microwave venting into kitchen. Ordered damper assembly needed to vent through the wall to the outside. Removed microwave, followed directions in original installation instructions, turned fan over, cut hole in wall, installed wall cap and replaced oven. Problem solved. Read more

Replacing a magnetron in my particular 9-year-old microwave (a microwave/hood combination) was not a simple “plug & play” operation. That is why I am placing this in the slightly difficult area. First, it takes 2 people to remove the microwave from the top of the stove. Next the main outer panel need to be removed. After that, 2 sheet metal panels need to be removed in order to expose the high voltage components for testing. Always discharge the high voltage capacitor first before doing... Read more

Checked switch with a voltmeter, determined the switch was bad. Ordered a new switch....watched a short how to you-tube video.....and from there.....it was fixed. Read more

Obtained the replacement motor and tray coupler from Appliance Parts Pro. Video of the typical replacement was very helpful to show what to expect and how to replace the motor and coupler. The removal of the bottom plate was held in place by several phillips screws. The motor was attached with two torx screws. The electric connection clips to the motor required needle nose pliers to pull them off. The tray coupler was simple to install after the motor was secured and bottom plate was replaced.. Read more

When the new bulb didn't want to go in, I felt around and realized the base of the old bulb was still in there. With some effort I got it out and new bulb in, Light cover fit fine, but did not come with a screw to hold it in. That would have been helpful. Read more

We found the parts on this website. Thanks to your search bar, we could see if the parts would work on our model microwave. Read more

Removed the microwave from the upper cabinet, then (partially) removed the black cover. We were able to access and remove the old mounting nut from inside the unit, and clip on the new one! Read more

I ordered a new magnetron and a new capacitor and after they arrived I set to work. I took plenty of pictures with my phone to remind me how the components came apart but it was pretty straight forward. Once the new parts were in and everything was reassembled the microwave worked good as new. The repair was less than a third the cost of replacement and no special tools are required. Just be careful to discharge the capacitor. This website is a great resource. Read more

I looked up the problem on the Appliance Pros forum and it sounded like the magnetron needed to be replaced. We looked up and ordered the part from Appliance Pros and replaced the magnetron 2 days later when we received it. It was not a difficult replacement but was tume consuming to take it down and remove the cover to get to the part. Within about 90 minutes, we had our microwave back on duty! Read more

The grill vent is only held in place by two screws. Super simple fix. Remove the two screws and the old grill vent, position the new vent and put the two screws back in. Replacing the cord required that cabinet to be removed. Lots of screws on the back, top and bottom. Once the screws were removed, the cabinet pulled back. The power cord connections were then clearly visible. Undid the two wire connectors and unscrewed the ground wire from the body to remove the old power cable. Installed the... Read more

Someone gave me this microwave over the range unit and was missing a few parts/accessories so I went to AppliancePartsPro's website and entered my model number and was able to find everything I was missing. So I placed the order and everything was in stock and shipped right out. So now I have a complete Microwave / over the range hood that performs like a new one with all it accessories. Read more