We use cookies and similar tools for site analytics and advertising. By using our site, you agree to this. See our Privacy Policy for details. Do Not Sell or Share My Personal Information
Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Front cabinet roller wheel for refrigerators. Mounts under the cabinet to allow smooth rolling and positioning. Replace if cracked, broken, or worn out.
Followed the instructions that was sent with wheel . wasn't to difficult. maybe 15 to 20 minutes total repair time,start to finish. Read more
Most orders arrive by Tuesday, November 24
Black hinge thimble for refrigerator doors. Replaces worn, cracked, or missing thimbles that support door alignment. Installs at top hinge.
Replacement fastener screw for appliances. Secures panels, trim, clips, and components. Needed when original screws are stripped, missing, or damaged.
Removed the handle with two screws on the inside front and pulled out the custom wood panel. Pulled the compactor out from under cabinet. Tipped it over on back of unit, supporting it with a little foot stool. Unscrewed two lower screws at bottom of unit holding black trim panel (that held wood panel in place) and lower black rubber flap. Removed two screws on lower outside side of unit that held the foot pedal. Slid off black U shaped metal frame from top of compactor towards bottom. Slid on... Read more
Cabinet roller axle supports refrigerator wheels for smooth movement. Replace if rollers wobble or fridge is hard to move. Verify fit with your model.
Left side wheels damaged from tenant running over floor register. Replaced all 4-rollers in rear and front of the refrigerator. Appliance Parts repair video was important to the success of the replacement. Read more
Supports the refrigerator door at the bottom pivot point. Replace if your hinge is rusted, bent, cracked, or broken to restore proper door alignment.
Looked up parts on internet using diagrams, ordered parts, they arrived in 2 days and installed them. Read more
This thermostat is a temperature-sensitive safety switch that monitors heat and opens or closes the circuit at a set point. Replacing a failed thermostat restores reliable temperature protection and corrects issues caused by tripping or stuck contacts.
Replaced the thermostat Read more
Magnetic door gasket creates an airtight seal to keep cold air in. Replace if worn, cracked, or not sealing properly to maintain temperature and efficiency.
This is a white exterior door handle that attaches to the refrigerator or freezer door, providing a grip for opening and closing. It mounts to the door with concealed screws or snap-in brackets. Replace this handle if it is cracked, broken, loose, or if the mounting points have become stripped and the handle no longer stays securely attached.
Purchased a new handle Read more
Fix clicking noise, poor cooling, or overheating compressor by replacing a cracked or warped condenser fan blade. Restores airflow across the coil.
At first, I thought that it was the defrost timer, but when I took apart the freezer, I found that the evaporator fan motor wasn't running, so I replaced it. Read more
Bottle with brush. Color: Black. Size: 0.6 fl.oz.
Replaced It With New One Read more
Stops refrigerator fan rattling and buzzing noise. This rubber grommet cushions the fan motor to reduce vibration. Simple DIY fix, takes under 30 minutes.
Ordered the parts from you guys, evaporator fan motor, fan blade, and new grommets. unscrewed the inside back panel of the freezer, removed the old fan, installed the new one. Read more
Refrigerator not cooling properly? A clogged filter drier prevents proper refrigerant flow. Requires professional installation due to sealed system.
Ordered new Evaporator part and Drier from Appliance Pros. The part arrived earlier than expected and was properly packaged. I had both parts installed by a professional as they required a level of expertise above my capabilities. Works perfectly. Read more
Fix clicking relay sounds, frozen fresh food, or warm freezer temps with this refrigerator control board. Regulates defrost cycles and cooling functions.
Color: Grey
The grill vent is only held in place by two screws. Super simple fix. Remove the two screws and the old grill vent, position the new vent and put the two screws back in. Replacing the cord required that cabinet to be removed. Lots of screws on the back, top and bottom. Once the screws were removed, the cabinet pulled back. The power cord connections were then clearly visible. Undid the two wire connectors and unscrewed the ground wire from the body to remove the old power cable. Installed the... Read more
This is a small white plastic plug that fills the hinge sleeve hole on a refrigerator or freezer door. It covers unused hinge mounting holes to provide a clean, finished appearance, especially after reversing the door swing. Replace this plug if it has cracked, fallen out, or gone missing, leaving an exposed hole in the door.
Took off the freezer door, took off the top hinge on the refrigerator door, replaced the handle, re-installed the top hinge and the freezer door. This is a two person job - one to remove the top hinge and replace the handle, while a second person holds the refrigerator door in place. Replacing the handle was easy. The most irritating part was figuring out what parts to order. The drawing of the refrigerator door (Drawing # 4) used to figure out what parts to order was not clear. I paid $8... Read more
This is a replacement screw designed to work with a wide range of household appliances. It is used for many purposes in these appliances, from holding body panels together to securing electronics into control boards. However, screws are subject to damage through corrosion, impact, and improper installation/removal. In most cases, the primary damage to this screw is through corrosion – it may become rusted or corroded in place, depending on the appliance and the maintenance provided during its lifespan. The screw may also be stripped or rounded due to improper removal or installation. If the screw is damaged, lost, or corroded in place, it will need to be replaced. In most cases, removal will require nothing more than a Phillips head screwdriver or the appropriately sized socket with a ratchet. However, if the screw is damaged, it may require a tap set to remove it from its mounting location. Note that this is a genuine OEM replacement screw made from durable, high-quality metal, and is sold individually. It fits Whirlpool, Maytag, Roper, Estate, Amana, Crosley, and Thermador appliances. It is used in over 150 machines, ranging from washers and dryers to air conditioners.
VERY EASY TO REPLACED OLD COVER-UNIT NEW COVER-UNIT. Read more