Wsse4220aww Parts

This double-style hinge bushing supports the washer lid hinge pin and provides a smooth bearing surface. Replacing a worn bushing restores quiet, even lid movement and helps keep the lid properly aligned over time.

• Supports and centers the lid at the hinge
• Provides a low-friction bearing surface for the hinge pin/rod
• Helps reduce squeaking, looseness, and metal-on-metal wear
• Can help resolve a wobbly, misaligned, or scraping lid

• Disconnect power before servicing; support the lid to prevent dropping
• Remove the hinge pin/rod or screws as your model requires to access the bushing
• Pry out the worn bushing and press the new bushing fully into the hinge opening
• Reassemble and check lid operation; consider replacing the opposite-side bushing if worn

This lid bumper cushions your washer lid where it meets the top panel, softening closure and protecting the finish. Replacing worn or missing bumpers reduces slamming and rattles for a quieter, smoother close.

• Cushions contact between the lid and top panel to reduce slamming noise
• Protects painted/enamel surfaces from chips and scratches at contact points
• Helps the lid sit level and minimizes vibration or rattling
• Replace if the bumper is missing, cracked, flattened, or hardened

• Disconnect power to the washer before servicing.
• Open the lid and locate the bumper(s) at the front corners (on the lid underside or top panel lip).
• Pull the old bumper straight out; clean the mounting hole.
• Press the new bumper firmly into the hole until fully seated and flush; test lid closure.

This pump and brake assembly drains water from the tub and applies the basket brake in your top-load washer. Replacing a worn assembly restores proper draining and a safe, prompt basket stop between cycles. What it does

• Pumps water out of the washer during drain and spin phases
• Applies the brake to stop the spin basket between cycles or when the lid switch is activated
• Helps reduce extended coast-down and stopping squeal
• Typical symptoms: standing water, slow/no drain, leaking at the pump area, basket coasts too long or squeals when stopping

• One pump and brake assembly

• Disconnect power and water supply; drain remaining water from hoses before service
• Access from the washer's underside; support the unit securely
• Transfer existing hoses/clamps to the new pump and secure all connections; if belt-driven, verify proper belt routing and pulley alignment
• Run a brief fill/drain test and recheck for leaks and proper basket stop

This leveling leg threads into the base of your washer to set height and keep the cabinet stable on uneven floors. Replacing worn or missing legs reduces vibration, walking, and noise for smoother, safer operation.

• Provides an adjustable foot to level and support the washer
• Helps reduce vibration, rocking, and "walking" during spin
• Replaces stripped, cracked, or missing leveling feet
• Helps with excessive shaking, rattling noises, or out-of-balance conditions

• Disconnect power and water; pull the washer forward for access.
• Support the appliance to prevent tipping; unscrew the old leg by hand or with pliers.
• Thread the new leg into the base; adjust all feet until level front-to-back and side-to-side.
• Ensure each foot contacts the floor firmly and the cabinet is stable before use.

This tub assembly replaces a cracked or leaking wash tub to restore proper water containment and drum support for your washer, helping reduce leaks, rubbing noises, and abnormal vibration during cycles. What it does:

• Provides the sealed reservoir that holds wash water and supports the inner drum during wash and spin cycles
• Helps stop or reduce water leaks caused by cracked or damaged tubs
• Can resolve rubbing, scraping, or thumping noises from a warped or broken tub
• Helps stabilize the drum to reduce vibration and improve spin performance

• Disconnect power and shut off water supply before starting; wear gloves and eye protection
• Tub assemblies are heavy and bulky—use two people or appropriate lifting equipment
• Follow the washer OEM service manual for disassembly, seal transfer/replacement, and torque specifications
• If bearings, seals, or mounting hardware show wear, replace them per OEM guidance for a complete repair

Includes 12 washers.

This small bushing fits the washer's lid hinge to provide a smooth, stable pivot. Replacing a worn hinge bushing restores proper lid alignment and helps reduce squeaks, rubbing, or excessive play when opening and closing the lid. What it does:

• Acts as a low-friction sleeve between the hinge pin and bracket
• Supports smooth lid movement and helps maintain alignment
• Reduces metal-on-metal wear and hinge noise
• Symptoms of wear can include squeaking, binding, scraping, or a loose/wobbly lid

• 1 hinge bushing

• Disconnect power before servicing
• Support the lid to prevent it from dropping when the hinge is loosened
• Remove hinge hardware to access and swap the bushing; reassemble and check lid alignment
• Many models use a bushing on each hinge—inspect both sides and replace as needed

Outer tub cover kit that replaces a cracked or missing washer tub cover, protecting the inner tub and helping stop rubbing, noise and fabric snags. Restores proper tub clearance for smoother drum movement and quieter operation. What it does:

• Covers the outer wash tub to protect the inner tub and fasteners from contact and wear
• Helps stop rubbing, scraping or thumping sounds caused by tub-to-tub contact
• Reduces the chance of clothes catching between the inner and outer tubs
• Restores correct tub spacing so the drum spins without interference

• Disconnect power and water supply before starting any repair
• Access may require removing the agitator or inner tub and using basic hand tools
• Inspect mounting clips, seals and surrounding components and replace any damaged items
• Test the washer on a short cycle after installation to ensure proper fit and quiet operation

Secure your washer's drain hose with this drain hose strap. It keeps the hose positioned at the standpipe or laundry tub, helping prevent movement, dislodging, and messy leaks when vibration increases during drain and spin cycles.

• Secures the drain hose to a standpipe or utility sink, per installation guidelines
• Helps prevent the hose from backing out or spraying water during operation
• Reduces strain and kinking by keeping the hose routed in place
• Replaces a missing, cracked, or broken strap

• Unplug the washer and turn off water supply before starting
• Position the drain hose in the standpipe or tub and tighten the strap to secure it without kinking the hose
• Maintain the manufacturer-recommended air gap and hose height per your installation manual
• Run a quick drain/spin to ensure the hose stays secured and there are no leaks

Size: 14-10 a trt 7/8 s.

This clip cover is a small snap-in plastic trim piece that protects and secures appliance panels or trim, giving a finished look and hiding fasteners. Replaces broken or missing covers to restore appearance and retention. What it does:

• Snaps into place to conceal screws or clip anchors on trim and panels
• Helps hold lightweight trim pieces securely to the cabinet or frame
• Prevents exposed fasteners and reduces snagging or sharp edges
• Useful when cracked, worn or lost covers cause loose or rattling trim

• One clip cover

• Disconnect power or unplug the appliance before accessing panels or trim
• Push the clip cover onto the mating clip or anchor until it snaps fully into place
• Use a small flat tool only to remove; avoid prying on surrounding trim to prevent damage
• Replace any damaged mounting clips before installing the cover for a secure fit

Size: 8-32 t. Includes 12 screws.

A single replacement screw used to secure appliance panels, trim, and internal brackets so components stay aligned and reduce rattling. Simple, direct-fit fastener for restoring proper mounting and stable operation. What it does:

• Secures panels, mounting brackets, trim pieces and other appliance components
• Helps stop rattling, vibration, or loose panels caused by missing or stripped fasteners
• Restores proper alignment of doors and access panels when original screw is lost or damaged
• Matches the OEM fastening point for a straightforward hardware replacement

• Disconnect power to the appliance before working on electrical components or access panels
• Use the correct screwdriver to avoid stripping the head; match drive type to the screw
• Tighten firmly but do not overtighten—stop when snug to avoid damaging threads or parts
• Keep removed fasteners organized and compare with the replacement to ensure correct fit

This shipping bar assembly secures the oven door and internal components during transport to prevent movement and damage. Replacing a damaged or missing shipping bar helps ensure the range or oven door stays protected while moving the appliance. What it does:

• Holds the oven door and internal parts in place during shipment to reduce jostling and impact
• Prevents door misalignment or damage caused by transit
• Helps avoid rattling or loose parts after relocation
• Used only for transport/protection; remove before regular appliance operation if instructed by manufacturer

• One shipping bar assembly

• Intended for use during shipping/transport — confirm removal instructions in your owner's manual before operating the appliance
• Install or remove with the appliance powered off and according to manufacturer guidance
• Keep small fasteners and clips secure; replace any missing hardware with OEM-specified parts

Size: 8 - 18 ab.

Alignment pin keeps the appliance door hinge aligned so the door closes evenly and seals correctly. Replacing a damaged pin restores proper door fit and helps stop sagging, rubbing, or uneven gaps. What it does:

• Positions and secures the door hinge during normal operation
• Restores correct hinge alignment when pins are worn or bent
• Helps eliminate door sag, misalignment, grinding, or difficulty closing
• Works with the hinge assembly to maintain an even seal and proper door movement

• Disconnect power to the appliance before beginning any repair; ensure the appliance is stable and cool.
• Support the door or hinge assembly while removing and installing the pin to avoid dropping or misaligning heavy components.
• Use basic hand tools; ensure pin orientation and full engagement in the hinge before testing.
• Keep small parts and fasteners secure during reassembly and test the door several times to ensure proper operation.