Wt7150cw Parts

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

Fix washer overfilling or not filling issues with a water level pressure switch replacement. Common repair for PE error codes. Takes 10-20 minutes to install.

This drain hose directs used water from your washer to the household drain. Replace if cracked, split, leaking, or chewed through by rodents.

Fix a washer that won't fill, leaks underneath, or drips constantly with this water inlet valve. Controls water flow into the drum. Easy DIY repair.

Dispenses detergent, softener, and bleach during wash cycles. Replace if cracked, clogged, or disintegrated. Confirm fit with your model number.

Washer not draining or making groaning noises during drain cycle? This drain pump assembly removes water and debris. Check for clogs first; moderate DIY.

Secures the stator to the motor assembly in your washer. Replace if bolt is stripped, spinning freely, or missing to restore proper motor stability.

Genuine hardware washer that distributes fastener load at assembly joints. Replace if worn, cracked, or causing loose connections. Confirm fit with your model.

This replacement nut secures bolts or studs in your appliance. Replacing a missing or stripped nut restores a tight, reliable connection to keep brackets and assemblies stable and reduce vibration or rattling. What it does:

• Provides threaded retention for bolts/studs on panels, brackets, and assemblies
• Helps maintain alignment and stability during operation
• Typical failure signs: stripped threads, missing hardware, loose or rattling components, vibration
• Direct replacement for the original nut in the same location

• 1 nut

• Disconnect power before service; shut off the water supply
• Match thread size/pitch to the original; start threads by hand to avoid cross-threading
• Tighten with the correct tool; do not overtighten or damage mating parts
• Reinstall any washers/spacers in the original order and verify secure fit

Molded trim piece that shields and supports the washer guide track assembly. Replace if cracked, broken, or missing to maintain smooth alignment.

Leaking water behind your washer? A cracked inlet hose is often the culprit. This hose channels water from your supply line into the machine during fill.

The Bellows Assembly is an OEM part for LG washers. The bellows assembly forms a watertight seal around the pump shaft to make sure water is properly drained from the washer tub during the spin cycle.

Causes of a bad drain pump bellows assembly can include split or cracked rubber from age, leaks that develop over time due to small cracks or porous areas of the bellows.

Symptoms of a bad drain pump bellows assembly include:

• Water not fully draining from the washer tub after cycles
• Excess water left in the tub requiring additional emptying
• Drips or leaks under the washer during or after draining
• Standing water or mold growth inside the pump housing

This LG part is also compatible with some Kenmore models.

Replacement mounting bracket holder that secures internal washer components. Needed when your original bracket is cracked, broken, or missing.

Washer won't switch cycles or hums during agitation? The clutch and housing assembly connects the motor to enable spin cycles. Moderately difficult repair.

Secures internal washer components in proper alignment. Replace this mounting bracket if cracked, rusted, broken, or missing to restore stability.

This damper controls airflow between compartments to help maintain consistent temperatures and efficient cooling. It replaces a worn or failed damper to restore proper air distribution and reduce temperature swings. What it does:

• Regulates airflow between freezer and fresh-food compartments for balanced temperatures
• Can cause uneven cooling or warm fresh-food compartment when faulty
• May click, stick, or fail to open/close if broken or obstructed
• Works with the refrigerator's control system to adjust airflow based on settings

• Disconnect power before beginning any service to avoid electric shock
• Handle the damper and housing carefully to avoid damage to plastic fins or linkage
• Note orientation and actuator connection before removal to ensure correct reassembly
• Test operation after reinstalling by restoring power and cycling temperature controls