Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Secures the door boot seal on front load washers to prevent water leaks. Replace if seal is loose or water seeps during wash cycles. Confirm fit with your model.
Im not a repairman, so all my knowledge to fix my washer came from either youtube or online chats. I posted this to help the next dad trying to save a few bucks. Door sensor... Since door sensor worked correctly, verified that by starting washer with door open, and agitate cycle would not start until door was closed. Meaning door sensor worked correctly. Timer... In high spin cycle washer sounded correcltly spinning, but when opening door, drum was was not moving. So timer was triggering... Read more
Extends your washer's drain hose to reach distant standpipes or sinks. Includes coupler and clamps. Replace when you need extra length for installation.
Attached drain hose extension and it more than reached the drain. Read more
Secures the motor to its mounting point in your laundry center. Replace if the retainer is worn, broken, or has lost tension to prevent motor misalignment.
I bought it here. It came quickly. I took the washer apart and put it in. Read more
Secures panels or brackets in your laundry center to prevent vibration noise. Replace missing, stripped, or worn screws to restore a tight fit.
Followed online video. It was easy Read more
Washer won't drain or clothes have residue? Replace the drain pump filter that screens debris and prevents clogs. Protects pump from damage.
On a 3 year old Maytag...........New gear case and hub installed. The videos produced by AppliancePartsPros are quite helpful, even though the video was not of the exact make and model number I was repairing, the similarities were so great that it may as well have been the same make and model number (whirlpool and Maytag essentially make the same thing and slap I different sticker on them) Read more
Fix a cracked or broken dispenser drawer that won't drain properly or is missing tabs. This drawer slides right in without tools—easy 5-minute swap.
Ordered a replacement Read more
Secures hose connections to prevent leaks in your washer. Replace if you notice dripping at hose fittings or loose connections. Verify fit with your model.
Took off cover, installed new parts. Read more
Fix a burnt or melted lid switch connector causing your washer to be completely dead. This terminal receptacle restores power to the lid switch.
Researched this kenmore washer on-line and found the problem to be the lid switch. Saw a diagram on how to jump this switch by connecting a wire to both outside wires on the harness and voila! It worked! This is not a fix but it allowed me to finish the load of unwashed clothes and told me which part was bad (do not run washer jumped like this.......fire hazard!) Ordered the lid switch and it was an easy repair. A $14.00 switch was a lot cheaper than a $450.00 washer. Thanks appliance parts... Read more
Cushioning pad that installs between the washer lid hinge and cabinet. Replace if cracked, worn, or missing to reduce squeaks and prevent metal wear.
Removed the screws, lifted the old lid out of the hinges. Replaced the hinges, set new lid in the hinges and replaced screws. Read more
Replacement screw for securing panels, brackets, and internal components. Replaces missing, stripped, or damaged fasteners to restore proper fit.
Replaced door latch and switch. Parts are plastic so you must know what you are doing to avoid breaking new parts. Videos were hard to find for my model - eventually I found a video that addressed a different problem but required disassembly of a washer cabinet similar to mine. I removed the control panel using a putty knife and unplugged the wire to the latch switch. Then I remove 3 screws securing the washer's top panel to the back panel. Using a rubber mallet, I gently knocked the top panel... Read more
Supports the spin basket on the center post for smooth, quiet rotation. Replace if your washer is noisy, vibrating excessively, or has poor spin performance.
Hex head screw for trash compactor assembly. Replaces lost, stripped, or damaged screws during repairs. Essential hardware for securing components.
This trash compactor is in our vacation home. We never use it and now we are selling the house. When I looked to replace it I was amazed at how expensive a new compactor would cost. I found the serial number on the current compact entered it and your web site came up. Your schematics were excellent and made the repair very easy! Read more
Fix a washer that won't start or stops mid-cycle with a new lid strike. Restores secure lid engagement. Takes about 5-10 minutes to replace.
Ordered the part, removed the broken lid lock, replaced it with the new one. Works fine. Read more
Replace your washer's anti-rattle clip to eliminate vibration noise and buzzing during cycles. Secures components with light spring tension. Confirm fit with your model number before ordering.
I bought a clutch liner kit installed it in 5 minutes now it spins faster than ever. Read more
Replaces a cracked, worn, or loose timer dial skirt that causes knob wobbling. Restores secure knob fit and proper alignment on the timer control opening.
Purchased this Whirlpool dial and watched you-tube. Just popped off cover and put on new part. Second time replaced in 7 years. Works great! Read more
Fix a slowly rotating or grinding agitator with this cam driven bearing. Often worn teeth cause agitation problems. Part of the complete cam assembly.