Need Help?
Call
Contains two, six foot long braided hoses with 90 degree ends.
I had a problem with the drain pump on my Kenmore HE3 and I replaced it using a drain pump I ordered from APP. That fixed that problem but once I started running the washer I started getting a FH error code. I looked it up and found that it was a problem with the washer not filling properly. I pulled the washer out and found that one of the fill hoses had kinked when I pushed the washer back in place. There was also some writing on the hose that read "Change hose every five years". I know I had... Read more
Shield cap for laundry center washers. Covers and protects internal components. Replace if cracked, broken, or missing to maintain proper enclosure.
The Screw is an OEM component compatible with Whirlpool washing machines. This screw secures the rear panel onto the cabinet frame, ensuring a sturdy connection between housing components. Proper installation is critical for the washer's structural integrity.
Causes of a bad screw include corrosion from repeated water exposure or stresses from years of use. Loosening can occur from vibrations weakening the threads over time.
Symptoms of a bad screw include:
This OEM Whirlpool replacement screw helps maintain a tight panel closure. It is compatible with additional brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
Size: 29 1/4 inches x 31 1/4 inches. This universal washer drip tray is large enough for duet washers and sits under the washer to protect your floors from scuffs, spill, etc. Includes a PVC drain fitting.
Used from harness to top.
Fixing the problem was quite simple. First, I removed the lid assembly (thanks to the diagrams supplied by AppliancePartsPros.com!). Getting the back two screws out was very difficult because I couldn't see them from the front and I could not move the unit out of the enclosed space. After some trial and error, I located the screws which were 5/16 hex head screws and removed them with a MAGNETIC nut driver. (The magnet assures that the screw will not drop down into the mechanism). Second, I... Read more
This is a small tube of silicone-based gasket sealer used to bond and seal gaskets during washer repairs. It creates a watertight seal between mating surfaces to prevent leaks around tub components or pump housings. Use this adhesive when replacing gaskets or resealing joints where the original sealant has deteriorated and water is leaking.
Screw: 8-16 x 3/8 inch.
Seals and secures the outer tub to reduce vibration in top-load washers. Replace if cracked, worn, or causing excessive noise during spin cycles.
Machine screw that secures panels, brackets, and components in appliances. Replace when worn, stripped, or missing to restore tight fit and stability.
Washer making noise or experiencing weak water circulation? This impeller cap secures the wash pump impeller for proper water flow and performance.
Hardware washer distributes load under fasteners to prevent loosening and reduce vibration. Replace when missing or damaged to restore secure fit.
Watched a video online, the project took about 20 minutes, went well, parts fit good, the video was very helpful in getting the wash machine up and running. Read more
Color: Gray. Size: 13 oz. can. Used for coating the dryer drum interior. Acrylic appliance paint.
Completely removed dryer drum cleaned surfaces ready for paint applied paint acquired from you it did a wonderful job with one can of paint will use for a while and acquire another can of paint for second coat thank you so much for your help the whirlpool dryer drum paint was exactly what it said it would do Read more
Connect hot and cold water faucets to your washer's inlet valves with this 2-pack of 5-foot fill hoses. Replace aging, cracked, or leaking supply lines.
- Didn't see any other leaks in machine. No grinding transmission noise. Assumed seal on transmission shaft was bad, since it was a central leak down the rotor. It was a little more difficult to dissemble than the video showed, but not too bad. Got it all back together and seems to be working well. No leaks yet. Didn't need washer in parts diagram - was already on the transmission. Also the drain pump filter was not necessary, it can just be cleaned. Read more
This water inlet valve controls the flow of hot and cold water into the washing machine during fill cycles. It uses electrically operated solenoids to open and close in response to signals from the control board. Replace this valve if the washer is not filling with water, filling slowly, leaking from the back, or continuing to fill when it shouldn't.
Size: 6-32 x 9/32 inch.
This replacement 7-2-1 screw secures components in compatible Whirlpool appliances, providing a dependable fastener for panels and assemblies. Use it to restore proper fitment and reduce rattling or loose parts. What it does
Replaced it with a new gear housing assembly. It was some what difficult removing the spindle hub. Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.