Waste Small Engine Flywheel Key Parts

Dryer door won't latch or stay closed? This strike plate mounts at the door opening to catch the latch securely. Easy DIY repair for reliable closing.

Spring-loaded belt tensioner that keeps the drive belt properly tightened. Replace if worn, seized, cracked, or causing squealing to restore smooth operation.

Washer won't start or lid won't latch? This lid strike assembly provides the catch point for secure lid closure. Easy DIY fix in under 30 minutes.

Replacement drum support roller for dryers. Mounts on the axle to support the drum and enable smooth rotation. Replace if worn, cracked, or noisy.

Dryer door won't stay closed? This door latch assembly secures your dryer door during cycles. Easy DIY repair with just 2-4 screws in minutes.

Dryer won't start or stops mid-cycle? A broken door strike prevents the latch from catching, so the control can't detect a closed door. Simple fix.

This small permanent magnet is used in supported refrigerator assemblies to actuate a mating reed switch or metal keeper. It helps the appliance recognize a closed position or hold a light cover/door closed for proper operation. What it does:

• Works with a reed switch or ferrous keeper to provide position sensing or magnetic latching
• Helps ensure features dependent on closed position operate correctly
• Can resolve issues where a small cover or door won't stay closed
• Address erratic "door ajar" indications tied to magnetic sensing

• Disconnect power and water before servicing
• Note the original magnet's location and orientation; polarity matters for proper operation
• Seat the magnet fully in its pocket or holder and align with the mating switch/keeper
• Test the related function before reassembling panels and trim

Fix a dryer door that pops open during the cycle with this door latch striker. Restores secure door engagement. Takes under 5 minutes to install.

Threaded metal shaft that mounts the idler roller in dryers and washer-dryer combos. Replace if bent, worn, or stripped threads prevent secure roller installation.

This is the door strike pin that engages with the door latch to keep the dryer door securely closed during operation. It is mounted on the dryer cabinet and catches the door latch when the door is shut. Replace this part if the dryer door will not stay closed, pops open during a cycle, or if the strike is visibly worn or broken.

A small rubber bumper that cushions and protects appliance doors, drawers or panels to reduce noise and prevent hard contact. Replaces worn or missing bumpers to restore a snug, quiet close. What it does:

• Provides a soft buffer to stop doors or drawers from banging into the cabinet or frame
• Reduces vibration and rattling during operation
• Helps doors and panels sit properly when closed
• Simple, non-electrical part — no wiring or adjustment required

• One replacement bumper

• Inspect the mounting hole or surface; clean debris before installing
• Press the bumper into the hole or onto the surface until fully seated; use a blunt tool if needed for tight fits
• Disconnect power to the appliance first and follow OEM instructions
• Remove old adhesive before installing the new bumper

This door catch assembly secures the door closed so your machine can start and run without interruptions. A worn or broken catch can keep the door from latching, causing cycles not to begin or to stop mid-cycle.

• Latches the door to engage the door switch and allow operation
• Helps prevent door popping open during use
• Common failure signs: door won't stay closed, must hold door to run, cycle won't start due to open-door indication
• Restores proper door alignment and engagement with the strike

• Unplug the appliance before servicing
• Open the door and remove the fasteners securing the old catch
• Transfer the new catch in the same orientation; reuse existing screws if not supplied
• Test door closure and latch engagement before resuming use

This is a single drum support roller that helps the dryer drum rotate smoothly during operation. The roller sits on a shaft at the rear or front of the drum and bears the weight of the drum as it spins. Replace this roller if the dryer makes a loud thumping, squealing, or rumbling noise during operation, or if the drum does not turn freely.

This is a small lever or catch that engages the door switch when the dryer door is closed, signaling the dryer that it is safe to operate. It also interacts with the belt switch mechanism to detect proper belt tension. Replace this part if the dryer does not start when the door is shut, runs with the door open, or if the lever is visibly broken or worn.

Washer won't start or advance to spin cycle? A broken lid strike prevents the lock from engaging. Simple 5-minute snap-in fix—just remove two screws.

Supports the dryer drum and allows smooth rotation. Replace if cracked, worn flat, or causing the drum to wobble. Installs on the axle at rear or front.