Back Panel Parts

Front panel case for room air conditioners. Replaces cracked, broken, or damaged exterior front case panels. Covers internal components and controls.

Outer door panel for top-mount refrigerators. Replaces cracked, dented, or discolored exterior door surfaces. Restores the clean appearance of your unit.

The mullion rail is the vertical divider strip that separates the fresh food and freezer compartments in side-by-side refrigerators, often housing the water and ice dispenser controls. This part needs replacement if you notice cracks in the plastic, damaged dispenser components, or poor sealing between compartments that affects temperature control.

Color: Grey

The Flapper Door with Mullion Heater is an OEM part for Whirlpool refrigerators. This part helps seal the gap between the refrigerator and freezer doors, preventing warm air from entering and cold air from escaping.  

Causes of a bad flapper door with mullion heater can include wear and tear over time, electrical issues affecting the heater, physical damage from repeated opening and closing of the doors, or warping due to temperature fluctuations.

Symptoms of a bad flapper door with mullion heater include:

• Condensation or frost buildup around the door seal
• Increased energy consumption due to temperature inefficiency
• The refrigerator door not closing properly
• Visible damage or wear to the flapper door or heater

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

Replaces broken or loose French door flipper assembly on refrigerators. Installs at top of left door to ensure proper closure and seal between doors.

Replacement fascia panel for dishwasher front interface. Installs on door to house control buttons and display. Needed when original is cracked or broken.

Vertical divider rail between refrigerator doors. Replace if cracked, broken, or not sealing properly. Installs with one screw. Easy DIY replacement.

This refrigerator door flipper mullion is the folding center rail that bridges the gap between the doors. It helps complete the door seal and reduces condensation along the center for better temperature retention.

• Bridges the gap between doors to complete the center seal and improve efficiency
• Folds out of the way when a door opens; flips into place as the doors close
• Helps limit moisture/sweating at the middle of the refrigerator
• Replaces a cracked, loose, or broken mullion that causes air leaks, doors popping open, or poor sealing

• Disconnect power before servicing; remove door bins for access
• Remove mounting screws; lift off the assembly and disconnect the harness if equipped
• Transfer any end caps/brackets; ensure spring orientation and proper wire routing during reassembly
• After installation, verify smooth flipping action and a continuous gasket seal down the center

Replace a cracked, broken, or worn dishwasher control panel fascia. This front panel covers the control buttons and display on your dishwasher door.

Restore a tight, even seal between your refrigerator's doors. This vertical mullion assembly flips into place to cover the center gap, helping maintain proper temperatures and reduce condensation.

• Bridges the gap between doors to create a continuous sealing surface
• Helps keep cold air in and warm air out for consistent cooling
• Aids proper door alignment and smooth closing
• Common symptoms of a failed mullion: broken or wobbly flipper, doors not closing fully or popping open, moisture/icing at the center, warming in the fresh food section

• Disconnect power before servicing and open the doors
• With the door open, release the retaining screws or tabs and lift the old mullion off the upper and lower pivots
• Position the new assembly on the pivots, secure it, and verify the flipper moves freely and seals evenly against the opposite door
• Restore power and recheck door operation and gasket contact along the full height

This fan switch restores dependable control of your appliance's ventilation fan. It routes power to the blower motor so you can turn the fan on and off from the control panel when the original switch becomes worn or fails.

• Controls electrical power to the blower motor
• Restores reliable on/off fan operation from the user interface
• Typical symptoms: fan won't start, won't shut off, runs intermittently, or the switch/rocker feels loose or broken
• Contacts can wear or arc over time from repeated use

• Disconnect power at the breaker or unplug the appliance before servicing
• Access the switch from the control panel; note wire positions and take a photo for reference
• Move wires one at a time to the matching terminals on the new switch; replace any heat-damaged connectors
• Reassemble, restore power, and test fan operation

Trim piece that secures the gap between refrigerator doors for a clean finish. Replace if cracked, broken, or missing to restore proper door fit.