Icemaker Thermistor Parts

This thermistor is the dishwasher's temperature sensor. It reports water temperature to the control so the heater and cycle timing are managed correctly, helping restore reliable wash performance and more consistent drying.

• Monitors water temperature in the tub/sump and sends readings to the control board
• Helps the control regulate heater operation and determine cycle progress/timing
• Failure can result in no heat or poor drying
• May cause unusually long/short cycles or temperature-related fault codes

• Disconnect power at the breaker and shut off the water supply before servicing
• Access is typically from the toe-kick/base area or sump; remove the lower access panel as needed
• Release the locking tab/clip, remove the sensor, and ensure the existing seal/O-ring is properly seated; install the new sensor fully to prevent leaks
• Reconnect the wire harness, restore power, and run a test cycle to check for leaks and proper heating

Dryer not heating or overheating? A faulty temperature control thermostat often causes inconsistent heat cycles. This part regulates dryer temperature.

Refrigerator not cooling properly or showing temperature errors? This temperature sensor monitors compartment temps and sends readings to the control board.

Ice dispenser not working or auger keeps falling off? This coupling connects the motor to the auger. Simple 15-minute DIY fix restores ice dispensing.

Ice bin cracked or warped? This container stores ice from your icemaker and guides cubes to the dispenser. Simple plug-and-play replacement part.

The Thermistor is an OEM Replacement Part that maintains the temperature inside your Frigidaire refrigerator. This thermistor handles reading the internal temperature. After reading, it transmits this information to the control system. At a temperature of 29 degrees, the thermistor should exhibit a resistance of about 35k ohms. While at room temperature, it should read approximately 5k ohms.

Causes of a bad thermistor can include regular wear and tear, exposure to moisture, or electrical issues. Over time, the thermistor may become less accurate or stop working altogether.

Symptoms of a bad thermistor include:

• Inconsistent or incorrect temperature readings
• The refrigerator being too warm or too cold
• The cooling system running continuously or not at all
• Error codes related to temperature control

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

Ice spilling in your freezer? A cracked ice bin won't store cubes properly. This container collects and holds ice from your icemaker securely.

A thin pad-style moisture sensor that detects wetness levels during the dry cycle and sends signals to the dryer control so the machine can adjust drying time. Replaces a worn or damaged sensor to restore reliable moisture-sensing performance. What it does:

• Detects residual moisture in the drum or on clothing and communicates readings to the control board
• Helps the dryer end cycles when items reach the set dryness level to prevent over-drying
• Common symptoms of a failing pad: long or incomplete drying cycles, clothes still damp at cycle end, or inconsistent auto-dry behavior
• Works as the sensing surface that partners with the dryer's sensing system to measure conductivity/moisture

• One sensor pad

• Disconnect power to the appliance before starting any repair
• Handle the sensor surface carefully; avoid touching conductive areas with bare hands or tools
• Install in the original mounting location and secure wiring connectors firmly; verify routing to avoid pinching

Fix frost buildup and warm temperatures caused by a faulty defrost thermostat. This sensor controls the defrost cycle. Simple 20-minute repair.

Fix a warm fridge or melting freezer ice cream. This defrost thermostat monitors evaporator temperature to prevent frost buildup and restore proper cooling.

Ice maker not making ice or overfilling? Replace the complete ice maker assembly to restore automatic ice production. Fixes jammed trays and leaking issues.

This complete unit produces ice cubes automatically within the freezer compartment of your refrigerator. Replace if ice production stops completely, produces hollow or malformed cubes, or leaks water inside the freezer.

This thermistor senses the temperature inside the refrigerator bin/drawer and provides the control board with the signal it needs to regulate cooling. Replacing a bad thermistor restores accurate temperature readings and more consistent cooling. What it does:

• Measures bin/drawer temperature and sends a voltage/ohm signal to the control board.
• Helps the refrigerator maintain set temperatures by enabling proper compressor/fan control.
• Common symptoms of a failing thermistor: incorrect bin temps, inconsistent cooling, or temperature-related error codes.
• Use when diagnostics point to a faulty temperature sensor or when the thermistor is damaged.

• Always disconnect power to the appliance before starting any repair.
• Handle the sensor and wiring gently; avoid contaminating or bending the sensing tip.
• Reconnect using the original connector and route the harness the same way to prevent pinching.

Freezer won't maintain temperature or cycles incorrectly? This thermistor sensor monitors temperature and signals the control board. DIY-friendly repair.

This dryer inlet thermostat monitors the temperature of incoming air and cycles the heater to maintain proper drying temperatures. Replacing a failed thermostat can restore consistent heat, help prevent overheating, and improve overall drying performance.

• Senses inlet air temperature and opens/closes electrical contacts to control the heat source
• Helps regulate drying temperature and protect against overheating
• Failure may present as long dry times, no or intermittent heat, overheating/shutting off, or erratic temperature swings
• Typically mounted on the air intake/duct or blower housing, depending on model

• Disconnect power before service; if gas, also shut off the gas supply
• Access the thermostat at the front duct or blower housing; note wire positions and transfer one at a time
• Mount flush against the metal surface with existing hardware to ensure proper sensing
• After installation, clear lint from ducting and vents to ensure proper airflow

This high limit thermostat is a safety device that monitors the heating element temperature in a room air conditioner with a built-in heater. It shuts off the heater if the temperature exceeds a safe threshold, preventing overheating and potential fire hazards. Replace this thermostat if the heater stops working, cycles erratically, or if the unit shuts off unexpectedly during heating mode.