Water Flow Sensor Parts

This temperature sensor mounts on the sealed-system gas inlet line in compatible refrigerators. It relays precise temperature feedback to the control so cooling and defrost cycles are managed correctly, helping maintain stable compartment temperatures. What it does:

• Senses temperature at the gas-inlet line; resistance changes are read by the control
• Helps regulate compressor, fan, and valve operation for proper cooling performance
• A failed sensor may cause erratic temperatures or extended run times
• Can correlate with control thermistor error codes or frost/ice patterns near the evaporator

• 1 thermistor sensor

• Disconnect power before servicing
• Note original sensor placement and insulation; reinstall in the same location and orientation
• Attach the sensor firmly to the line and route the harness as originally, away from sharp, hot, or moving parts
• Do not open or puncture sealed-system tubing; if damage is suspected, stop.

Reduces chlorine, sediment, lead, and mercury from drinking water. Replace every 6 months or 400 gallons for optimal performance. Verify fit with model.

This kit includes a replacement heating element and a high limit thermostat for an electric dryer. The heating element generates the hot air that dries your clothes, while the high limit thermostat acts as a safety device to prevent overheating. Replace this kit if your dryer is not producing heat, takes too long to dry clothes, or shuts off prematurely due to overheating.

Fix dryer that won't stop or shows tO error code. This moisture sensor assembly monitors drying cycles. Moderate DIY repair, 30-45 minutes.

Replacement water supply hose for dishwashers. Connects household water line to the dishwasher inlet. Replace if cracked, leaking, or damaged.

This thermistor is a temperature sensor that monitors conditions in your refrigerator and sends signals to the control board to regulate cooling cycles. It ensures your refrigerator maintains the correct temperature for food safety and energy efficiency. Replace this sensor if your refrigerator is running too warm or cold, cycling on and off frequently, or displaying temperature error codes.

Fix sensor cook cycles that won't adjust properly or show sensor errors. This humidity sensor monitors moisture levels for automatic cooking adjustments.

Fix frost buildup and warm fridge temps. This defrost thermostat monitors evaporator temperature to prevent overheating during defrost cycles.

Removes contaminants and improves water taste in your refrigerator. Replace every six months for optimal performance. Confirm fit with your model number.

This thermistor is the dishwasher's temperature sensor. It reports water temperature to the control so the heater and cycle timing are managed correctly, helping restore reliable wash performance and more consistent drying.

• Monitors water temperature in the tub/sump and sends readings to the control board
• Helps the control regulate heater operation and determine cycle progress/timing
• Failure can result in no heat or poor drying
• May cause unusually long/short cycles or temperature-related fault codes

• Disconnect power at the breaker and shut off the water supply before servicing
• Access is typically from the toe-kick/base area or sump; remove the lower access panel as needed
• Release the locking tab/clip, remove the sensor, and ensure the existing seal/O-ring is properly seated; install the new sensor fully to prevent leaks
• Reconnect the wire harness, restore power, and run a test cycle to check for leaks and proper heating

The Thermistor is an OEM Replacement Part that maintains the temperature inside your Frigidaire refrigerator. This thermistor handles reading the internal temperature. After reading, it transmits this information to the control system. At a temperature of 29 degrees, the thermistor should exhibit a resistance of about 35k ohms. While at room temperature, it should read approximately 5k ohms.

Causes of a bad thermistor can include regular wear and tear, exposure to moisture, or electrical issues. Over time, the thermistor may become less accurate or stop working altogether.

Symptoms of a bad thermistor include:

• Inconsistent or incorrect temperature readings
• The refrigerator being too warm or too cold
• The cooling system running continuously or not at all
• Error codes related to temperature control

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

Dryer not heating or overheating? A faulty temperature control thermostat often causes inconsistent heat cycles. This part regulates dryer temperature.

In-line filter installs behind refrigerators without built-in filtration. Reduces contaminants for clean, fresh water. Replace every 6 months.

Connects internal water lines in your dishwasher. Replace if cracked, worn, or leaking to restore a secure seal and prevent water damage under the unit.

This is a decorative cover that fits over the air filter compartment inside the refrigerator. It conceals the air filter while allowing airflow to pass through for proper air circulation and freshness. Replace this cover if it is cracked, broken, discolored, or if the clips that hold it in place have snapped off.

Replaces cracked, brittle, or leaking dishwasher drain inlet hose. Connects drain pump to disposal port. Essential for models showing LE error codes.