Water Temperature Sensor Parts

This thermistor is the dishwasher's temperature sensor. It reports water temperature to the control so the heater and cycle timing are managed correctly, helping restore reliable wash performance and more consistent drying.

• Monitors water temperature in the tub/sump and sends readings to the control board
• Helps the control regulate heater operation and determine cycle progress/timing
• Failure can result in no heat or poor drying
• May cause unusually long/short cycles or temperature-related fault codes

• Disconnect power at the breaker and shut off the water supply before servicing
• Access is typically from the toe-kick/base area or sump; remove the lower access panel as needed
• Release the locking tab/clip, remove the sensor, and ensure the existing seal/O-ring is properly seated; install the new sensor fully to prevent leaks
• Reconnect the wire harness, restore power, and run a test cycle to check for leaks and proper heating

Replaces cracked, brittle, or leaking dishwasher drain inlet hose. Connects drain pump to disposal port. Essential for models showing LE error codes.

This sensor assembly detects moisture levels inside the oven cavity, typically used to support auto-cook or convection functions that rely on humidity readings. It mounts inside the oven and connects to the control board via a wire harness. Replace this sensor if the oven is overcooking or undercooking food during auto-cook cycles, or if you receive an error code related to the humidity sensor.

Routes wastewater from your dishwasher to the sink drain or disposal. Replace if your existing hose is cracked, leaking, kinked, or too short for installation.

This dryer inlet thermostat monitors the temperature of incoming air and cycles the heater to maintain proper drying temperatures. Replacing a failed thermostat can restore consistent heat, help prevent overheating, and improve overall drying performance.

• Senses inlet air temperature and opens/closes electrical contacts to control the heat source
• Helps regulate drying temperature and protect against overheating
• Failure may present as long dry times, no or intermittent heat, overheating/shutting off, or erratic temperature swings
• Typically mounted on the air intake/duct or blower housing, depending on model

• Disconnect power before service; if gas, also shut off the gas supply
• Access the thermostat at the front duct or blower housing; note wire positions and transfer one at a time
• Mount flush against the metal surface with existing hardware to ensure proper sensing
• After installation, clear lint from ducting and vents to ensure proper airflow

Size: 7 foot long.

Fix frost buildup and warm temperatures caused by a faulty defrost thermostat. This sensor controls the defrost cycle. Simple 20-minute repair.

This high-limit thermostat is a safety device that monitors the oven's internal temperature and cuts power to the heating element if the temperature exceeds a safe threshold. It helps prevent overheating and potential fire hazards. Replace this part if your oven shuts off unexpectedly, fails to heat at all, or triggers error codes related to excessive temperature.

Removes contaminants and improves water taste in your refrigerator. Replace every six months for optimal performance. Confirm fit with your model number.

Replace your refrigerator's ice and water filter housing assembly when cracked or damaged. Restores proper fit and protects internal components. Verify compatibility with your model number before ordering.

This is a decorative cover that fits over the air filter compartment inside the refrigerator. It conceals the air filter while allowing airflow to pass through for proper air circulation and freshness. Replace this cover if it is cracked, broken, discolored, or if the clips that hold it in place have snapped off.

This high limit thermostat is a safety device that monitors the heating element temperature in a room air conditioner with a built-in heater. It shuts off the heater if the temperature exceeds a safe threshold, preventing overheating and potential fire hazards. Replace this thermostat if the heater stops working, cycles erratically, or if the unit shuts off unexpectedly during heating mode.

Routes wastewater from your dishwasher pump to the home drain. Replace if cracked, kinked, punctured, or worn to restore proper drainage and prevent leaks.

Fridge not defrosting or has excessive frost buildup? This defrost thermostat monitors evaporator temperature to control the defrost cycle. 15-minute fix.

This water filter installation kit contains the fittings needed to install or replace a refrigerator water filter assembly, restoring proper connections and helping prevent leaks at the filter interface. What it does

• Provides the connection fittings and hardware used to attach a refrigerator water filter assembly to the appliance water line.
• Re-establishes sealed water flow where old or damaged installation parts caused leaks.
• Can address issues like reduced or intermittent water flow when caused by missing or broken filter fittings.
• Works with the refrigerator's existing water line and filter housing.

• Turn off the refrigerator water supply before beginning; relieve pressure by dispensing water until flow stops.
• Follow the refrigerator manufacturer's installation instructions and use only parts specified for your model.
• Inspect tubing and connections for damage; replace any worn components to ensure a proper seal.

This 250V 15A safety fuse protects the appliance's line circuit from overcurrent. When the original fuse has blown, replacing it can restore power and help safeguard internal components from further damage.

• Opens the circuit if excessive current or a short occurs, protecting internal parts
• Common symptom: unit completely dead—no display, lights, or response to controls
• Blown fuse will test open (no continuity) with a multimeter
• If a new fuse blows again, another component may be shorted and needs diagnosis

• Unplug the appliance before servicing; microwaves can retain a dangerous charge—discharge the high-voltage capacitor
• Access the fuse near the line filter/control area; note clip orientation
• Replace only with the same 250V 15A rating; never bypass or upsize the fuse
• If the replacement fuse blows immediately, stop and troubleshoot the root cause