Hardware Hand Small Engine Regular Starter Parts

This run capacitor helps the refrigerator compressor start and run smoothly, restoring normal operation when a weak or failed capacitor causes the compressor to struggle. Replacing a faulty capacitor can reduce humming and improve cooling performance. What it does:

• Provides continuous phase-shift to the compressor motor for stable running.
• Helps maintain proper compressor speed and efficiency during operation.
• Commonly replaced when the compressor hums, won't stay running, or cooling is inconsistent.
• Reduces risk of repeated motor cycling caused by a weak or open capacitor.

• Always disconnect power to the appliance before accessing electrical components.
• Discharge the capacitor before handling; capacitors can hold a charge even when powered off.
• Observe terminal orientation and mounting location; replace with the same type and ratings.

Fix a refrigerator that hums and shuts down or won't start with this compressor overload protector. Simple DIY repair that restores safe operation.

Mounting screw secures range components and panels. Replace if screw is stripped, missing, or damaged during appliance repair or maintenance work.

Freezer won't cool or makes clicking/humming sounds? This compressor start relay restores reliable motor startup. Simple DIY fix in under 30 minutes.

Hardware kit for mounting microwave to wall and cabinet. Includes screws, bolts, and washers for secure installation. Replaces lost or missing fasteners.

Compressor won't start or runs intermittently? This start relay and overload helps the motor get up to speed so your refrigerator runs reliably again.

Size: 8-18 x 1/2 inch.

This compressor overload is a thermal/protective device that helps prevent compressor damage by cutting power when the motor overheats or draws excessive current. It restores normal operation once conditions return to safe levels. What it does:

• Protects the refrigerator compressor from overheating and electrical overloads
• Works with the compressor start relay to help the motor start and run properly
• Common symptom linkage: replaces a failed overload when the compressor hums but won't start
• Stops compressor cycling or prevents repeated trips that cause cooling loss

• One compressor overload (single piece as shown)

• Disconnect all power before replacing to avoid shock or injury
• Handle terminals carefully and reconnect matching terminal positions
• Replace only with the same part number or equivalent
• If compressor still won't start after replacing the overload, check the start relay and compressor condition.

A replacement unified-thread screw used to secure appliance panels and internal components. Provides a direct fastener to restore secure attachment when original screws are missing, damaged, or corroded. What it does:

• Fastens panels, brackets, trim pieces, and other appliance components that use a unified-thread screw.
• Restores secure mounting to reduce rattling, movement, or misalignment of parts.
• Replaces stripped, rusted, or missing screws to help maintain safe operation.
• Works where the appliance's service manual or parts diagram specifies a unified-thread fastening point.

• Disconnect power and water before servicing for safety.
• Use the correct screwdriver or bit to avoid stripping the head; install by hand until started, then snug—do not overtighten.
• Replace like-for-like: match thread type and length to the removed screw to ensure proper fit and function.
• If other fasteners show corrosion or damage, inspect nearby hardware and replace as needed.

3mm x 8mm screw secures trim, panels, and brackets inside your microwave. Replace missing or stripped screws to restore proper fit and alignment.

Fix a refrigerator that won't cool or start. This compressor start relay helps your compressor run reliably and prevents clicking sounds. Easy DIY repair.

Mounting hardware kit for securing your microwave during installation. Includes brackets and fasteners needed when original components are missing or damaged.

This door removal tool helps release and lift an oven door from its hinge pins so the door can be serviced or the inner glass replaced more safely. It provides stable support during door removal to reduce damage risk. What it does:

• Assists in releasing and lifting the oven door off its hinge pins for service or glass replacement.
• Stabilizes the door to help prevent sudden drops or shifting while removing or handling the door.
• Reduces the chance of scratching or chipping the door glass and oven frame during removal.
• Useful whenever the door must be removed for repairs, cleaning, or part replacement.

• Review the correct door-removal procedure before use.
• Ensure the appliance is powered off and fully cooled. Support the door with a second person if it is heavy.
• Use the tool only as described in the service instructions; improper use can damage the door or hinges and risk injury.

Fix a clicking fridge that won't cool with this compressor overload protector. Protects motor from overheating damage. Simple 10-15 minute DIY repair.

Replacement mounting screw for electric wall ovens and ranges. Secures panels, brackets, and trim pieces. Replaces lost, stripped, or damaged screws.

Secures the handle to your dryer or microwave door panel. Replace this self-tapping screw if missing, stripped, or damaged to restore a firm grip.