User Interface Board Parts

Range won't turn off or functions stay powered on? This relay board controls electrical flow to range components. Common fix for stuck-on appliances.

Dishwasher stops mid-cycle or won't start? The control board regulates wash and dry cycles. A failed board causes no power or incomplete cycles.

Control board that mounts to the main control assembly. Replace when board is burned, damaged, or relays have failed to restore proper operation.

Replace your dishwasher's membrane touch pad keypad when buttons become unresponsive, cracked, or worn. Installs behind the control panel for reliable use.

Fix dishwasher lights that won't blink or buttons that don't respond. This user interface board reads your selections and starts cycles reliably.

Electronic control board with integrated touch pad for freestanding freezers. Replaces failed boards with unresponsive buttons, cracked touch panels, or damaged controls.

Fix a dishwasher that won't start, cycles won't change, or lights flash with this electronic control board. Coordinates all wash and drain functions.

The Noise Filter is an OEM part for Whirlpool built-in wall ovens. It is installed inside the oven cavity near components that produce vibrations, such as the convection fan motor. 

Causes of a faulty noise filter include the degradation of noise-dampening materials over many heating and cooling cycles. Physical damage from accidental impact during cleaning could also compromise its sound-blocking ability.

Symptoms of a bad noise filter include: 

• Excessive buzzing or humming noises emitted from the oven cavity
• Louder than normal fan or component sounds carrying into the kitchen
• Vibrations felt externally on the oven chassis during operation

This OEM replacement fits several Whirlpool, KitchenAid, and Jenn-Air wall oven models.

This OEM part is a refrigerator dispenser interface. The dispenser interface is responsible for the main functions of the refrigerator, such as adjusting the temperature settings as well as the other functions that are displayed on the interface. If the refrigerator is no longer cooling efficiently, failing to maintain temperature, dispensing water, or the touchpad is unresponsive, the interface might need to be replaced. Thankfully, replacing this part is not a difficult process.To replace the old interface, make sure that all power to the refrigerator is turned off. Open the refrigerator door and remove the door panel of the interior of the refrigerator. Locate the old control board and remove the wire harnesses that connect to it. Take note of the wire connector's orientation and reinsert the wires to the new board. Snap the new interface back in place and reinstall the inner panel. This genuine replacement part is sold individually and is compatible with General Electric, Hotpoint, and RCA brand refrigerators.

Fix continuous beeping, blank display, or temperature control issues in your refrigerator. This control board restores normal operation. DIY repair.

This electronic main control board manages and distributes power to the appliance's key components. Replace a failed board to restore normal operation when the unit won't power up, won't start, or runs erratically.

• Regulates and routes incoming power to motors, fans, compressors, heaters, and valves based on signals from sensors and the user interface
• Coordinates cycle timing and system protections to help prevent component damage
• Logs or triggers fault indications when abnormal conditions are detected
• Common failure symptoms: no power, dead/unresponsive controls, intermittent shutdowns, or unpredictable operation

• Disconnect power at the breaker or unplug the appliance before servicing
• Handle the PCB by the edges and use ESD protection to avoid static damage
• Photograph wiring and move connectors one at a time to the new board
• Inspect connected loads (motors, heaters, compressor, valves) for shorts before restoring power

Fix a refrigerator that won't cool, has no display, or won't respond to settings. This control board restores function to your bottom-mount refrigerator.

Fix a dishwasher that won't start, shows error codes, or has unresponsive controls. This main control board manages cycles and user interface functions.

Fix a refrigerator with no lights, no cooling, or blank display. This power supply board converts AC to DC for electronic controls. DIY-friendly repair.

Replaces the front control panel console on your dishwasher. Houses buttons and interface for selecting cycles and options. Needed when cracked or worn.

Replaces your dishwasher's touchpad control panel assembly. Houses selection buttons on the door. Needed when buttons are unresponsive, cracked, or broken.