Hardware Hand Small Engine Start Switch Parts

Fixes burner that won't heat or stays on one temperature. This infinite switch restores variable heat control to your cooktop surface element.

Fix burners stuck on high or won't adjust temperature with this selector switch. Restores reliable control of cooktop functions. Moderate DIY repair.

Fix a compressor that won't start, hums, or cycles on and off every few minutes. This motor start capacitor restores reliable compressor operation.

This 3-position temperature switch selects the dryer's heat level so the appliance reaches the desired drying temperature. It replaces a worn or faulty selector to restore proper temperature selection and consistent drying performance. What it does:

• Switches between three temperature settings to control dryer heat levels.
• Routes power to the heater circuit based on the selected heat setting.
• Commonly replaces a switch that causes incorrect heat, no heat on some settings, or inability to change temperature.
• Works with the dryer's control system and thermostats to maintain selected drying temperature.

• Disconnect power to the appliance before attempting any service.
• Handle terminals and connectors carefully; match wiring to original locations or take a photo before removal.
• Verify operation with a multimeter for continuity per service manual before and after installation.

This switch assembly restores dependable control of your range hood or ventilation unit, helping resolve unresponsive or intermittent controls so the appliance turns on, off, and changes settings as expected.

• Provides the user interface to turn functions on/off and change settings
• Failure signs include no response on certain settings, intermittent operation, or a stuck/loose actuator
• Heat, moisture, and normal wear can degrade internal switch contacts over time
• Replacing the switch restores smooth, consistent operation

• Disconnect power at the breaker before servicing
• Access the control area and photograph wiring to document positions
• Move wires one at a time to the new switch; ensure tight, fully seated connections
• Reassemble and test all functions before finalizing

This speed nut is a clip-on fastener that provides threads for a screw on the appliance. It secures sheet-metal panels, brackets, or trim and helps keep assemblies tight under vibration and repeated use.

• Provides captive threads so a screw can tighten into thin sheet metal
• Helps secure panels, brackets, and trim pieces in place
• Replace if a screw spins without tightening, a panel rattles/feels loose, or the original clip is missing or damaged
• Restores a snug, reliable attachment point without a loose nut

• Disconnect power and, if applicable, shut off gas; allow the appliance to cool before servicing
• Note the clip's orientation; slide it onto the panel edge or stud as designed
• Start the screw by hand to avoid cross-threading; do not overtighten
• Wear cut-resistant gloves when handling sheet-metal parts

6-20 x 3/8 inch nickel screw secures trim panels, brackets, and small components in dishwashers and ovens. Replace missing or stripped screws.

Range hood light won't turn on or off? This lamp switch controls power to the light circuit. Simple 10-minute repair restores proper lighting function.

Fix burners that won't light or spark inconsistently with this cooktop spark igniter switch. Restores reliable ignition on gas burners. Takes 15 minutes to install.

This run capacitor helps the refrigerator compressor start and run smoothly, restoring normal operation when a weak or failed capacitor causes the compressor to struggle. Replacing a faulty capacitor can reduce humming and improve cooling performance. What it does:

• Provides continuous phase-shift to the compressor motor for stable running.
• Helps maintain proper compressor speed and efficiency during operation.
• Commonly replaced when the compressor hums, won't stay running, or cooling is inconsistent.
• Reduces risk of repeated motor cycling caused by a weak or open capacitor.

• Always disconnect power to the appliance before accessing electrical components.
• Discharge the capacitor before handling; capacitors can hold a charge even when powered off.
• Observe terminal orientation and mounting location; replace with the same type and ratings.

Washer won't agitate or spin? Lid switch detects when lid opens/closes to control operation. Test for continuity before replacing. DIY-friendly repair.

Fix PE error codes and water overfilling issues with this pressure switch. Monitors tub water level to control fill and drain cycles. 30-minute DIY repair.

Refrigerator not cooling or won't start? A failed compressor start device prevents startup. DIY repair in under 30 minutes restores reliable cooling.

This is a replacement screw used to secure panels, trim, or small components on compatible Whirlpool appliances. Installing the correct fastener restores proper fit and helps stop rattles or loose trim. What it does:

• Secures trim, panels, or control components to prevent movement and rattling
• Replaces missing or damaged hardware that can cause gaps or loose parts
• Helps maintain proper alignment of panels and movement-free operation
• Used wherever a factory screw of this size and head style is specified

• Always disconnect power (and water, if applicable) before servicing the appliance
• Use the correct screwdriver or driver bit to avoid stripping the head
• Install by hand until threads engage, then tighten snugly—do not overtighten
• Keep removed hardware organized before final reassembly

Hood slide switch won't stay in position or settings aren't responding? This sliding selector control restores reliable function. Simple 15-minute fix.

Oven light switch.