Central Pack Line Mover Float Needle Parts

After reviewing a few blogs it was clear that Frigidaire is knows there is a problem. One of the blogs recommended AppliancePartsPros.com for a new pressure sensor switch and a water inlet valve. Ordered the part and it was shipped that day, as promised. Pulled the dishwasher out (which was the hardest part of the repair). The pressure sensor switch is a changed out with a small flat blade screw driver to release two snap clips. The inlet valve is changed out with three screws and on hose... Read more

• Will not fill with water

Performed diagnostic continuity tests on fill valve and overflow switch as recommended. Fill valve continuity test failed. Ordered part Saturday, shipped the following Monday, in my hands by the following Wednesday, installed and operational by Thursday. Great service! Thanks. Read more

• Will not fill with water

Changed inlet valve super easy on my whirlpool dishwasher took the front kick panel off turned off water and electricity the valve was right out front bottom left one small sheet metal screw held it on disconnected plug and 5/8 water line and hose with clamp for fill to tub just reverse for install of new valve Read more

Leak was slow but becoming gradually worse. Pulled dishwasher out from under counter then visually inspected sump while it ran. As soon as the water got very hot, I could see the sump leaking where it meets the stainless pan. Searched for the correct sump gasket without success. Turns out that the gasket is built into the sump for this model. The built-in gasket is very narrow (under-engineered IMHO which is probably why it developed a leak). Thanks to Simon's excellent videos at... Read more

Replacing the heating element and float switch with AppliancePartsPros.com hardware and Repair Clinic YouTube videos. Just followed the videos and made the swaps. Was able to complete and test all repairs in a single evening. Read more

Removed bottom cover, located leak at float switch, removed and replaced float switch kit. The toughest part of the repair was removing the Float & Retainer Assembly (in the interior of the machine tank) which broke when I pushed it back and pulled it straight up as suggested in the service manual. The Float Switch Kit (attached to, and below the float, below and outside the tank) has a folding plastic cover which fastens with plastic clips. If you open the switch kit before removing the... Read more

I bought a new controller first and installed it. The exact replacement controller was no longer available and I had to modify two AC connectors that changed from 3 pins with two wires to two pins with two wires. This was not expected but I made it work just fine by getting the three pin connectors on the cable to fit the two pin by breaking out the center web in the board two pin and then shaving off the raised key plastic on the wires. Then on power up, I found that the wash motor did not... Read more

I first installed the inlet pump with no results. I then ordered a Control Switch and Float and Nut. This fixed the problem. Everything comes out so clean. I also replaced the filter which allowed me to clean debris around old filter. It is also easier to replace all these parts with the dishwasher pulled out and tilted on its side. I had to pull mine out to unplug power to the dishwasher. Read more

Prior to ordering parts I had pulled the pump strainer basket and cleaned it out. There was both soft and hard scale build up. The tub-to-pump hose was also pretty crusty/slimey. Still got warnings for SUDS and repeated F02 errors. Ordered parts and replaced the pump, tub-to-pump hose, interior drain hose and exterior drain hose (both hoses has some slime build up). The water standing in the tub when I emptied it the first time had very little suds but we kept getting the SUDS warning. ... Read more

I replaced the drain pump, drain hose, and sump filter. Repairs took me about 2 hours. I just followed the advice from the videos which are great by the way. I had to pull the washer back out to tighten the drain hose connection but my washer is working like new again. Read more

I watched a suggested video about my model and was able to easily take apart the filter unit and access the drainage area. I found a worn out "Float" Valve. In the process of replacing the float valve I went ahead and replaced a gasket and the Valve, Check. Repairs went great. Parts were a perfect fit. This is the second time I used AplliancePartsPros. Read more

Replaced the drain valve. duh. here's the kicker...original problem was circulation pump was broken. Paid $350 to have it "professionally" fixed, and when we turned it on, it wouldn't run, so "professional tech" said "it must be the control panel". So I say maybe, send him away, checked the indicator panel and sure enuf, drain valve light. So I ordered it here, replaced the valve, and it ran really funky with weird noises, Then water starts leaking under dw. So I figured I did something... Read more