Power Small Engine Primer Bulb Parts
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3391914
Dryer won't heat or overheats? The high limit thermostat monitors drum temperature. Moderate DIY repair with heater housing access required.
Do-It-Yourself Stories from Customers like You
My whirlpool dryer was not getting hot Anthony D. • Sanibel , FL • May 01, 2016
I purchased a new heating element. Very easy to fix in about twenty minutes
Read more
More
Genuine Broan part
By: Broan
Part Number: S97018564
Replace your range hood light lens cover to protect bulbs from grease and restore even lighting. Snaps into place in under a minute. Confirm fit by model.
Do-It-Yourself Stories from Customers like You
Cracked light lens cover for hood range Terry D. • Yucaipa , CA • July 13, 2015
Snapped the old cover off and installed the new one. Although this is a simple fix the hard part was to determine appliance product year. Apparently the part was redesigned after a certain year and two types were available. There is a label underneath the hood that contains various information such as serial number etc. There may also be a product date code which is what you need to determine manufacturing information. You will need to provide this information to the salesperson in order to get...
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: W11594027
Light socket assembly houses your oven bulb and provides electrical connections to illuminate the interior. Replace when bulb won't stay secure or light fails.
Do-It-Yourself Stories from Customers like You
The light socket was bad in the oven Richard D. • Florence , AL • January 31, 2016
I ordered a new socket and replaced the socket and now we have a light in the oven. The project took about 10 minutes and was easy done.
Read more
More
Genuine Samsung part
By: Samsung
Part Number: DC47-00017A
Dryer won't heat or stops heating mid-cycle? The high limit thermostat cuts power when temperatures spike. Easy 15-minute fix with video guide.
Do-It-Yourself Stories from Customers like You
My dryer would not heat up Chris R. • Glen Saint Mary , FL • January 07, 2015
When starting my dryer the motor would power up and rotoe the drum and blower. Afetr about 20-30 seconds the igniter would come on then the gas valve would open and I would get heat for about 6 or 7 seconds then it would shut off. I know the burner is suppoed to cycle on and off but once the burner shut off it would not come bqack on unless I shut the dryer off and then back on. I checked for continuity on the thermistor, the thermal fuse and the high temp sensor. All three of them appeared to...
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10467289
The Water Temperature Sensor is an OEM part for Whirlpool washing machines. This sensor ensures the water is reaching the proper temperature at each stage of the wash cycle. Note: The sensor does not include the seal W11590578. Order separately if needed.
Causes of a bad temperature sensor can be failures over time due to mechanical wear, thermal stress on electronic components, or damage from leaks/flooding inside the unit.
Symptoms of a bad water temperature sensor include:
- Inability to switch between wash steps or advance through the cycle
- Erratic or inconsistent temperature readings
- Failure alarms or error codes displayed
- Improper or incomplete washing even on high heat settings
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
Do-It-Yourself Stories from Customers like You
F2 e3 error code on front load duet washer Mark M. • Saratoga Springs , NY • September 16, 2016
Replace the water temperature sensor and still had the error code. While I had the back of the machine open I ran the washer. I traced the black wires from the temperature sensor and wiggled them as the washer was running. At one zip tie every time i moved the wires the washer would stop running and the error code would flash. Sure enough, like many others posted, the vibration from the machine had split the wire. I spiced the wire back together and have not had a problem since.
Read more
More
Genuine Ge part
By: Ge
Part Number: WR01X37886
Illuminates water and ice dispenser area for visibility in low light. Replace when bulb burns out or dispenser area stays dark. Confirm fit with model.
Do-It-Yourself Stories from Customers like You
No lights in refrigerator Lance B. • League City , TX • November 06, 2020
We bought a new house that has a 15 year old GE Monogram built in fridge. The home warranty people sent two guys out saying it was nearly impossible to repair the fridge and they both suggested buying a completely new freezer door for the fridge and of course the warranty company said it was preexisting and we weren't covered. Shocker.
I have lighting in the freezer but not the fridge. I purchased a door switch and replaced the old one but that didn't do the trick. So i purchased a 2 amp fuse...
Read more
More
Genuine Frigidaire part
By: Frigidaire
Part Number: 218906802
Replace your refrigerator light socket when bulbs won't illuminate or burn out quickly. Provides secure bulb connection and prevents overheating. Verify fit.
Do-It-Yourself Stories from Customers like You
Refrigerator light stopped working Ed O. • Rapid City , SD • March 01, 2015
Went to the Internet, entered the make and model number, read possible causes, viewed videos on fixes and determined it was probably the socket. Viewed the schematic to determine the correct part number. Ordered a new socket. Received it within three days and in less than 5 minutes replaced the light socket. Problem solved and the light now works. Appreciated the videos, ease in ordering and quick delivery.
Read more
More
Genuine Ge part
By: Ge
Part Number: WR55X25754
LED light assembly illuminates refrigerator interior compartments. Replace when lights dim or fail to ensure proper visibility of contents. Verify fit.
Do-It-Yourself Stories from Customers like You
GE model gfe28gskjss refrigerator pin point led lights all dim (5 total) Robin D. • Tuscaloosa , AL • September 12, 2020
To fix: it is one of two issues. #1) Main circuit board is going bad (should put out 12 volts-can check with voltmeter for 12VDC output) #2) One or more led light circuit board is bad. Easiest to check for #2 issue first. Open doors and pop out (but do not disconnect ) all 5 led lights (1 on each side and 3 across top). Using voltmeter check for DC voltage to each light individually. Each led light should pull 2VDC. If a led pulls 5VDC - 20VDC, then that is your bad light. Unplug 2 wire pin...
Read more
More
Genuine Frigidaire part
By: Frigidaire
Part Number: 316022500
Signals when your range burners or oven are active. Replace when light fails to illuminate or stays on constantly. Confirm fit with your model number.
Do-It-Yourself Stories from Customers like You
A burner switch went bad in our electric stove and an indicator light burnt out Steve G. • Hanover , PA • January 05, 2015
The repair was a success. The switch and came looked different from the original. I called Appliance Parts Pro, they lady on the phone said that Frigidaire changed the switch and how to wire it up correctly. Problem solved. It all works as it should.
Read more
More
Genuine Frigidaire part
By: Frigidaire
Part Number: 137539200
Dryer won't heat or shows E66 error? The thermal limiter prevents overheating by monitoring airflow. Moderate DIY repair, requires rear panel access.
Do-It-Yourself Stories from Customers like You
E66 error code. Door open came on and dryer would not turn on at all other than display of error. Bruce H. • South Elgin , IL • March 15, 2014
I actually found a post from another brave soul who was willing to try to fix his, and had stated when he put the new limiter switch in, it fixed the problem.
Since the whole back of the dryer needs to come off to get to the burner, and the limiter switch is inexpensive it seemed like common sense to take this approach first. After all, you don't put a new engine in your car if all it needs is a new battery!
I also found posts that an overheating event could fry the main control board, and...
Read more
More
Genuine Lg part
By: Lg
Part Number: 6912W1Z004B
Replace your microwave's interior or underside light bulb when dim or burned out. Restores visibility for monitoring food. Confirm fit with your model.
Do-It-Yourself Stories from Customers like You
Interior light and turntable failed at the same moment. Stacey B. • New Bern , NC • February 01, 2021
Knowing the odds of 2 failures occurring at the same exact time was unusually high, I just searched your site for what other broken items might affect these two failures. Came up with next control item upstream and tallied that item failure with percentages of successful repairs, (4 mins.) door safety switch.
Since I had to change out the most likely of the 3 and since I was already was going to be into the switch panel I ordered all 3 and swapped them all out to cover my butt, as they were...
Read more
More
Genuine Speed Queen part
By: Speed Queen
Part Number: D510523
Fix dryer overheating issues with this thermistor assembly. Monitors temperature and sends readings to the control board. DIY-friendly repair part.
More
Genuine Frigidaire part
By: Frigidaire
Part Number: 316557300
Indicator light lens covers and protects the burner signal light on your range. Replace when cracked, discolored, or missing. Confirm fit with your model.
Do-It-Yourself Stories from Customers like You
Contact stuck had to cut power to turn off oven burnt brownies broiler element went wild Mike H. • East Leroy , MI • March 07, 2015
Called for a repair tech, he told me what the problem was, I had already checked out the burnt connections,repair was going to be $450-500 range, My wife & I discussed repair or new range,repair won out.I am a retired machine repairman with some elect skills,so looked up parts online ordered them, installed the new control board with the new "decal" , checked out the oven, etc, everything seems good to go. This range is only 6.5 yrs old , they don't seem to make them last as long as the ones I...
Read more
More
Genuine Ge part
By: Ge
Part Number: WB08X10016
Holds the light bulb securely in your microwave for proper interior illumination. Replace if bulb won't stay in place, socket is burned or cracked.
Do-It-Yourself Stories from Customers like You
Installing replacement light bulb sockets (wb08x10016) on my ge microwave (jvm1440bd003) Peter W. • Chesterfield , VA • March 17, 2025
I recently tackled a repair on my GE microwave (model JVM1440BD003, manufactured in 2003) to replace the light bulb sockets for the under-microwave lights. Since one socket was failing, I decided to replace both at the same time to avoid future issues. I used two WB08X10016 light sockets, which are the correct OEM parts for this model.
The process started off smoothly thanks to a helpful installation video on the website. It made the job look straightforward: remove five screws to drop the...
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: W11338583
Replace your refrigerator's interior light bulb when dimming, flickering, or burnt out. Restores visibility inside fridge and freezer compartments.
Do-It-Yourself Stories from Customers like You
My led light bulb went out in my freezer Belinda G. • Cushing , TX • October 30, 2016
I ordered my bulb from AppliancePartsPros.( By the way it only took 2 days to get my order). Put it in and now I have light ! Thank you so much !!
Read more
More
Genuine Frigidaire part
By: Frigidaire
Part Number: 134786100
This moisture sensor consists of two metal strips typically mounted inside the dryer drum area that detect the moisture level in clothing during a drying cycle. It signals the control board to end the cycle when clothes reach the desired dryness. Replace this sensor if your dryer shuts off too early with clothes still damp, runs too long, or if the auto-dry cycle no longer functions properly.
Do-It-Yourself Stories from Customers like You
The sensor-moisture clip was broken off and needed to be replaced. Edgar D. • Bradford , AR • April 06, 2014
Simple unscrewed the set screw, removed the broken sensor-moisture part, attached the leads, and reattached the part to the back of the dryer. Took about 4 minutes.
Read more
More