Hardware Hand Small Engine Safety Switch Parts
Genuine Ge part
By: Ge
Part Number: WC21X20249
The Return Switch is an OEM part for GE trash compactors. This part ensures that the compacting ram returns to its starting position after each compaction cycle.
Causes of a malfunctioning return switch can vary from electrical issues, such as short circuits or worn-out connections, to mechanical problems, including physical damage from wear and tear or blockages preventing the switch's activation.
Symptoms of a faulty Return Switch include:
- The compactor ram fails to return to its original position after a compaction cycle.
- The unit does not start or operate correctly, indicating issues with the cycle initiation.
- Unusual noises or behavior from the trash compactor, suggesting that the ram is not aligning or moving as expected.
This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.
Do-It-Yourself Stories from Customers like You
The trash compactor would not cycle without me holding kick plate up for whole cycle when it did get back to the top of the cycle it would only stop if i opened the door Mike D. • Pine Mountain , GA • December 15, 2014
TALKED TO YOUR REPRESENTATIVE AND WE WENT THROUGH ALL THE ON/OFF AND LIMIT SWITCHS. NARROWED IT DOWN TO TWO SWITCHS. THE ON/OFF SWITCH AND THE LIMIT SWITCH ON THE DOWN CYCLE SIDE. REPLACED ON/OFF AND DETERMINED THAT THAT WAS NOT THE ISSUE. THEN UNCOVERED LIMIT SWITCHS AND REPLACE DOWN SWITCH, FIXING THE PROBLEM
Read more
More
$10.77
- Compare At:
-
$12.82
- You Save:
-
$2.05
Genuine Whirlpool part
By: Whirlpool
Part Number: WP9759474
Burner stuck on high heat or won't regulate temperature? This infinite switch controls heat levels on your cooktop. DIY repair in 20-30 minutes.
Do-It-Yourself Stories from Customers like You
One of the burners would stay on max heat no matter what heat setting was selected Ismael C. • Amherst , OH • March 14, 2015
I replaced the Infinite switch on the cooktop panel and that corrected the problem.
Read more
More
$82.95
- Compare At:
-
$99.54
- You Save:
-
$16.59
Genuine Samsung part
By: Samsung
Part Number: DC96-01703C
Washer overfilling or not filling properly? The water level pressure switch controls fill cycles. Easy 15-minute DIY repair with our video guide.
This part fixes the following symptoms
-
Will not stop filling with water
See more...
Do-It-Yourself Stories from Customers like You
Samsung clothes washer wa456 code ie u6 John D. • Howard Beach , NY • February 28, 2015
This error code indicated faulty water level and wash cycles were exhibiting either no water or too much water. Saw utube vid using this part for this type of problem and so far the repair is working well. Part arrived in 2 days, it was the right part and the machine is working the way its supposed to so I'm very happy. The worst scenario would have been to hire a repair guy to rip me off for a "Johnson Rod" I didn't need.
Read more
More
$90.95
- Compare At:
-
$109.14
- You Save:
-
$18.19
Genuine Whirlpool part
By: Whirlpool
Part Number: W11120795
Fix a burner that won't heat, stays hot, or can't adjust temperature. This infinite switch controls power levels. Simple DIY repair in 5-10 minutes.
Do-It-Yourself Stories from Customers like You
Stem broke off on surface unit switch Robert Z. • Hampstead , MD • July 09, 2016
Replaced switch with a new one. also replaced the 4 knobs
Read more
More
$73.95
- Compare At:
-
$88.00
- You Save:
-
$14.05
Genuine Ge part
By: Ge
Part Number: WH12X10498
Fix a washer that won't fill with hot or cold water. This rotary temperature switch controls water temperature settings. Easy 5-minute DIY repair.
This part fixes the following symptoms
-
No hot or cold water
-
Will not fill with water
See more...
Do-It-Yourself Stories from Customers like You
No hot water would fill the washer in any cycle or temperature setting if the temperature setting was set to "hot" absolutely nothing would happen when turned on (cold washes worked fine) William H. • St Louis , MO • December 30, 2014
Replaced the water temperature selector switch. After watching a YouTube video for our GE top loading washer showing the switch replacement, I replace the switch in under 5 minutes! Very easy!
Read more
More
$18.95
- Compare At:
-
$22.55
- You Save:
-
$3.60
Genuine Bosch part
By: Bosch
Part Number: 00422748
The Potentiometer is an OEM replacement part for Bosch gas range or cooktops. It functions as a three-terminal resistor that adjusts the flow of electric current, which in turn, controls the ignition and temperature of the cooktop. This component is essential for the precise operation and control of the gas burners, ensuring they light up and maintain the desired flame intensity.
Causes of a malfunctioning Potentiometer can be attributed to wear and tear, electrical issues, or damage due to spills and cleaning products. A compromised potentiometer affects the flow of electric current, leading to issues with the ignition and temperature control of the gas burners.
Symptoms of a bad Potentiometer include:
- The cooktop not lighting or staying lit
- The ignitor continuously clicking without igniting the burner
- Inability to adjust the flame intensity or temperature accurately
This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.
Do-It-Yourself Stories from Customers like You
One burner on my thermador cooktop (pcs484ccus) would not light Kinn K. • Haslet , TX • June 08, 2015
After watching a youtube video, I disassembled the front cover on the cooktop (be sure to turn off the power supply). I then switched the potentiometers on two burners. The burner that was not working now worked and the burner that did work did not. Easy to find the culprit....ordered a new potentiometer from here and though I only got regular shipping, it was actually delivered the NEXT DAY! 5 minutes, put in the new part, and all burners work. Great site, thanks for the help!
Read more
More
$56.95
- Compare At:
-
$67.77
- You Save:
-
$10.82
Genuine Frigidaire part
By: Frigidaire
Part Number: 316540900
The Screw is an OEM part for Frigidaire ranges and cooktops. This part secures the burner head in place, ensuring proper alignment and functioning of the burner.
Causes of a bad burner head screw can include loosening due to repeated heating and cooling cycles, damage from impact or mishandling, or simply wear and tear over time.
Symptoms of a loose or missing burner head screw include:
- Uneven or irregular flame pattern on the burner
- Burner head not sitting flush or properly aligned
- Burner head wobbling or moving during use
- Potential gas leaks if the burner head is not securely fastened
This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Ignitor failed / screw that attached burner to ignitor stripped Michael M. • Roundhill , VA • May 17, 2015
Ordered new Ignitor / Orifice and screws
Mike was a great resource, he helped me thru the project.
Read more
More
$19.95
- Compare At:
-
$23.74
- You Save:
-
$3.79
Genuine Ge part
By: Ge
Part Number: WE4M255
Fix a dryer timer that won't advance or automatic cycles that stopped working. This timer resistor regulates cycle duration. Easy 15-minute repair.
Do-It-Yourself Stories from Customers like You
Dryer would not shut off at end of any cycle Jeffrey S. • Davis , CA • January 15, 2018
I Replaced the power resistor. The old resistor had a small burnt spot and tested infinity for resistance.The terminals were too small so I had to make new connector. Any 5000 ohm ceramic filled resistor would have worked also.
Read more
More
$32.95
- Compare At:
-
$39.21
- You Save:
-
$6.26
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10420741
The Push to Start Switch is an OEM replacement part for Whirlpool dryers. Located on the control panel, it allows the user to initiate the drying cycle with the push of a button. This switch is designed to withstand the repetitive motions of starting countless loads over the dryer's lifespan.
Causes can be gradual wear of internal components like contact pads from activations, or moisture intrusion corroding circuit pathways over time.
Symptoms of a faulty push-to-start switch include:
- The dryer failing to start even when powered on
- Inconsistent or intermittent operation of the start button
- The dryer starting unintentionally without input
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models.
Do-It-Yourself Stories from Customers like You
The push start button didn't start the dryer Kirsten K. • Fayetteville , NC • July 21, 2016
I replaced the part i ordered and it worked great!
Read more
More
$27.37
- Compare At:
-
$32.30
- You Save:
-
$4.93
Genuine Frigidaire part
By: Frigidaire
Part Number: 134813601
The Door Switch is an OEM part for Frigidaire dryers. This part ensures that the dryer operates safely by only allowing the machine to run when the door is completely closed. Positioned typically at the door frame, the switch activates when the door is shut, signaling the control system that it's safe to begin the cycle.
Over time, door switches can wear out or become damaged, which can interfere with the normal operation of the dryer.
Symptoms of a faulty Door Switch include:
- The dryer not starting when the door is closed.
- The dryer stopping unexpectedly, which might be due to a loose or faulty switch.
- A lack of the usual "click" sound that indicates the door has latched properly, suggesting the switch isn’t engaging.
- The dryer continuing to run when the door is opened, which poses a significant safety risk.
This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Dryer will start, run for a few second, then turn off. No error codes John M. • Waikoloa , HI • April 03, 2014
By reading the forums I first thought it may be the thermostat. I bypassed the thermostat wiring and the dryer still turned off after a few second of running. The second check was for the door switch. I couldn't find an explanation of how to bypass, so I just ordered a new one to try. It worked.
Read more
More
$27.95
- Compare At:
-
$33.26
- You Save:
-
$5.31
Genuine Whirlpool part
By: Whirlpool
Part Number: 12001908
Fixes washer that won't agitate, spin, or start. If your washer stops mid-cycle or won't run with lid closed, this lid switch kit restores operation.
This part fixes the following symptoms
-
Will not fill with water
-
Won't start
See more...
Do-It-Yourself Stories from Customers like You
Washer would not turn on Anthony W. • Washington , DC • October 23, 2014
No water, no electricity, nothing happened when I pulled the on knob. I replaced the lid switch. The switch arrived at my house super fast - ordered on Friday and was there on Saturday. The whole replacement process took no time at all.
Read more
More
$46.35
- Compare At:
-
$55.62
- You Save:
-
$9.27
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10563095
Dryer won't start when you press the button? This push to start switch initiates the motor and heating element. Simple 5-minute DIY replacement.
Do-It-Yourself Stories from Customers like You
Would not start Charles Y. • Auburn , NY • June 19, 2018
Replaced the start s/w
Read more
More
$63.65
- Compare At:
-
$75.74
- You Save:
-
$12.09
Genuine Ge part
By: Ge
Part Number: WB24T10022
Burner not heating or stuck on? This surface element switch controls power to your cooktop burners. Common repair when heat won't adjust properly.
Do-It-Yourself Stories from Customers like You
Burner didn't work Larry W. • Aiea , HI • March 23, 2014
Replaced the switch infin by watching the video
Read more
More
$105.95
- Compare At:
-
$126.08
- You Save:
-
$20.13
Genuine Ge part
By: Ge
Part Number: WE4X448
The Flame Sensor is an OEM part for GE dryers. This part detects the presence of a flame in gas dryers, ensuring that the gas ignites properly for safe and efficient drying.
Causes of a bad flame sensor can include regular wear and tear, carbon buildup from the gas flame, or electrical malfunctions.
Symptoms of a bad flame sensor include:
- The dryer not heating or taking longer to dry clothes
- The dryer shutting off unexpectedly during a cycle
- The igniter glowing but not igniting the gas
- Error codes related to heating or ignition issues
This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.
This part fixes the following symptoms
-
No heat or not enough heat
See more...
Do-It-Yourself Stories from Customers like You
Dryer heating for only a short time then no heat at all David N. • Fairfax , CA • December 08, 2018
GE Gas Dryer Model DBVH512GF1WW began to heat for only a short amount of time so drying clothes took WAY too long. Read online that the first thing to replace are the solenoids. Bought the two solenoids from AppliancePartsPros.com for about $50 total, and it seems to have fixed the problem. Had to watch a few videos to learn to disassemble the dryer, and the job took a couple of hours, but now that I know what I'm doing it could be done in less than 30 minutes.
Also, the old solenoids tested...
Read more
More
$78.41
- Compare At:
-
$93.31
- You Save:
-
$14.90
Genuine Ge part
By: Ge
Part Number: WB24X10146
The Micro Switch is an OEM part for GE microwaves. This part ensures the appliance operates only when the door is securely closed. It controls the electrical circuit, allowing the microwave to start heating food when the door latch engages the switch.
Causes of a bad micro switch can include wear and tear from frequent use, electrical issues, or physical damage from slamming the microwave door.
Symptoms of a bad micro switch include:
- The microwave not starting or stopping unexpectedly
- The microwave running even with the door open
- Intermittent power issues
- The door not latching or the microwave indicating the door is open
This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Stopped working tripped breaker Roberto M. • Pembroke Pines , FL • March 08, 2019
By replacing the switches.
Read more
More
$41.47
- Compare At:
-
$49.35
- You Save:
-
$7.88
Genuine Frigidaire part
By: Frigidaire
Part Number: 318293827
Burner won't turn on or heat properly? This range burner control switch restores heat level adjustment. Moderate DIY with wiring terminal labels.
Do-It-Yourself Stories from Customers like You
Large burners would go to high when turned on Charles H. • Prestonsburg , KY • October 25, 2016
Replaced infinite switch on large burners and just went ahead and replaced the infinite switch on the small burners while I had it apart and installed all new surface elements as well...parts were shipped the next day and I received them within 2 days...
Read more
More
$73.95
- Compare At:
-
$88.00
- You Save:
-
$14.05