Hardware Hand Small Engine Start Switch Parts
Genuine Whirlpool part
By: Whirlpool
Part Number: 12002125
If your dual burner only works on high or won't heat at all, this dual infinite switch kit restores full temperature control. Moderate difficulty install.
Do-It-Yourself Stories from Customers like You
Range dual surface unit would only go on in "high" setting not on any other settingsje Kenneth C. • Tolland , CT • July 28, 2015
Replace dual infinity switch. The only difficulty is the terminal labels on the new switch did not match at all with the terminal labels on the original switch. The enclosed instructions were NOT helpful. But I contacted your representative, Johnny, and he was most helpful and patient. From my model number he located very specific and detailed instructions for how to wire the new switch. The rest of the job was easy. Your representative was outstanding. Thanks.
Read more
More
$57.39
- Compare At:
-
$75.66
- You Save:
-
$18.27
Genuine Frigidaire part
By: Frigidaire
Part Number: 318191023
If your dual burner stays on low and won't turn off, or the small element doesn't heat, this infinite switch may need replacing. DIY-friendly repair.
Do-It-Yourself Stories from Customers like You
Large element was very erratic on temperature low/high. Rodney C. • Lake Wales , FL • March 01, 2018
Replaced the infinite, dual, switch. Very good instructional video for Safety, removal * install.
Read more
More
$62.43
- Compare At:
-
$74.29
- You Save:
-
$11.86
Genuine Bosch part
By: Bosch
Part Number: 00165256
Dishwasher won't fill or keeps overfilling? The float switch detects water levels for proper filling and draining. Accessible repair in under 30 minutes.
This part fixes the following symptoms
-
overflowing
-
Will not fill with water
See more...
Do-It-Yourself Stories from Customers like You
Inlet valve would not open to let water into the dishwasher Kurt J. • Burnsville , MN • January 09, 2015
I checked continuity at the float switch since I knew the inlet valve was working when direct wired to 120v. Switch did not have continuity. Replaced switch and inlet valve worked at start of cycle.
Read more
More
$31.35
- Compare At:
-
$37.62
- You Save:
-
$6.27
Genuine Frigidaire part
By: Frigidaire
Part Number: 297237702
Compressor clicks but won't start? Replace the start relay when your freezer stops cooling or the compressor shuts off after a few seconds. Quick fix.
Do-It-Yourself Stories from Customers like You
Refrigerator quit cooling Mitchell M. • Jackson , GA • May 12, 2017
First I have an LG French Door with a bottom freezer. It quit cooling. I went on line and watched some very informative You Tube videos. I trouble shot according to these videos. In these videos it shows that if there is a click coming off the compressor it has too meanings, the compressor is froze or the start relay is bad. I ohmed the compressor and had no open wires in the compressor. I then shook the relay and it was making noise. The videos stated that is there is a noise in the relay...
Read more
More
$79.95
- Compare At:
-
$95.94
- You Save:
-
$15.99
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3395382
The Start Switch is an OEM replacement part for Whirlpool dryers. It is an electronic component responsible for initiating the heating elements and tumble cycles upon user command from the control panel.
Causes of a bad start switch involve general wear over extended use. Failure of the internal conducting surfaces interrupts circuit activation as well.
Symptoms of a bad start switch include:
- Heating elements or tumble cycles that will not engage properly
- Dryer fails to operate or stops mid-cycle unexpectedly
- Control panel appears non-responsive to selections
- Error codes related to ignition or power delivery faults
Note: This dryer push-to-start switch has 2 terminals.
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore electric dryer models.
Do-It-Yourself Stories from Customers like You
Dryer wouln't start heard the timer working but the starter wouldn't start Perry B. • Stockton , CA • December 05, 2014
I replaced the starter switch, that really didn't need to be replaced, and the thermal fuse, which did.
Read more
More
$50.57
- Compare At:
-
$59.67
- You Save:
-
$9.10
Genuine Frigidaire part
By: Frigidaire
Part Number: 134762010
Fix a washer that won't fill, overfills, or shows E35 error code with this water level pressure switch. Moderate DIY repair takes about 1-2 hours.
Do-It-Yourself Stories from Customers like You
E35 Michael B. • Mechanicsville , VA • September 13, 2016
Water valve not closing all the way. Water keep entering washer even with power cord unplugged. Parts I ordered fit perfect. Ordered on Thursday night , parts there Saturday. Great service and shipping. Thank
Read more
More
$45.95
- Compare At:
-
$60.39
- You Save:
-
$14.44
Genuine Ge part
By: Ge
Part Number: WB24T10022
Burner not heating or stuck on? This surface element switch controls power to your cooktop burners. Common repair when heat won't adjust properly.
Do-It-Yourself Stories from Customers like You
Burner didn't work Larry W. • Aiea , HI • March 23, 2014
Replaced the switch infin by watching the video
Read more
More
$109.52
- Compare At:
-
$129.23
- You Save:
-
$19.71
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10420741
This push-to-start switch initiates the dryer cycle when the start button is pressed. It sends a signal to the motor and control circuit to begin tumbling and heating. Replace this switch if pressing the start button produces no response, the dryer only runs while you hold the button down, or the switch feels loose or does not click when pressed.
Do-It-Yourself Stories from Customers like You
The push start button didn't start the dryer Kirsten K. • Fayetteville , NC • July 21, 2016
I replaced the part i ordered and it worked great!
Read more
More
$27.37
- Compare At:
-
$32.57
- You Save:
-
$5.20
Genuine Frigidaire part
By: Frigidaire
Part Number: 316540900
The Screw is an OEM part for Frigidaire ranges and cooktops. This part secures the burner head in place, ensuring proper alignment and functioning of the burner.
Causes of a bad burner head screw can include loosening due to repeated heating and cooling cycles, damage from impact or mishandling, or simply wear and tear over time.
Symptoms of a loose or missing burner head screw include:
- Uneven or irregular flame pattern on the burner
- Burner head not sitting flush or properly aligned
- Burner head wobbling or moving during use
- Potential gas leaks if the burner head is not securely fastened
This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Ignitor failed / screw that attached burner to ignitor stripped Michael M. • Roundhill , VA • May 17, 2015
Ordered new Ignitor / Orifice and screws
Mike was a great resource, he helped me thru the project.
Read more
More
$19.95
- Compare At:
-
$23.74
- You Save:
-
$3.79
Genuine Whirlpool part
By: Whirlpool
Part Number: W10339251
Fix a washer that overfills, won't fill to the right level, or floods. This water level pressure switch monitors tub water. DIY install in 1 hour.
Do-It-Yourself Stories from Customers like You
Water level control wouldn't work Micheal W. • Millville , UT • April 11, 2014
I replaced it and the new one fit perfectly. reassembled and fired it up. Worked as desired, like new...
Read more
More
$140.30
- Compare At:
-
$166.96
- You Save:
-
$26.66
Genuine Ge part
By: Ge
Part Number: WB24T10063
Fix a burner stuck on high or not heating with this infinite control switch. Common cause when burners won't adjust temperature. DIY repair in 20 minutes.
Do-It-Yourself Stories from Customers like You
Burner only worked on high setting Alejandro G. • East Meadow , NY • February 15, 2016
Ordered recommended part for GE appliance. Change was very simple. Followed instructions on video and removed one wire at a time. Very easy to change 5 to 10 minutes.
Read more
More
$85.37
- Compare At:
-
$102.44
- You Save:
-
$17.07
Genuine Ge part
By: Ge
Part Number: WE4M255
Fix a dryer timer that won't advance or automatic cycles that stopped working. This timer resistor regulates cycle duration. Easy 15-minute repair.
Do-It-Yourself Stories from Customers like You
Dryer would not shut off at end of any cycle Jeffrey S. • Davis , CA • January 15, 2018
I Replaced the power resistor. The old resistor had a small burnt spot and tested infinity for resistance.The terminals were too small so I had to make new connector. Any 5000 ohm ceramic filled resistor would have worked also.
Read more
More
$34.95
- Compare At:
-
$41.59
- You Save:
-
$6.64
Genuine Ge part
By: Ge
Part Number: WB24X10146
The Micro Switch is an OEM part for GE microwaves. This part ensures the appliance operates only when the door is securely closed. It controls the electrical circuit, allowing the microwave to start heating food when the door latch engages the switch.
Causes of a bad micro switch can include wear and tear from frequent use, electrical issues, or physical damage from slamming the microwave door.
Symptoms of a bad micro switch include:
- The microwave not starting or stopping unexpectedly
- The microwave running even with the door open
- Intermittent power issues
- The door not latching or the microwave indicating the door is open
This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Stopped working tripped breaker Roberto M. • Pembroke Pines , FL • March 08, 2019
By replacing the switches.
Read more
More
$41.54
- Compare At:
-
$49.85
- You Save:
-
$8.31
Genuine Ge part
By: Ge
Part Number: WH12X10498
Fix a washer that won't fill with hot or cold water. This rotary temperature switch controls water temperature settings. Easy 5-minute DIY repair.
This part fixes the following symptoms
-
No hot or cold water
-
Will not fill with water
See more...
Do-It-Yourself Stories from Customers like You
No hot water would fill the washer in any cycle or temperature setting if the temperature setting was set to "hot" absolutely nothing would happen when turned on (cold washes worked fine) William H. • St Louis , MO • December 30, 2014
Replaced the water temperature selector switch. After watching a YouTube video for our GE top loading washer showing the switch replacement, I replace the switch in under 5 minutes! Very easy!
Read more
More
$18.95
- Compare At:
-
$22.36
- You Save:
-
$3.41
Genuine Whirlpool part
By: Whirlpool
Part Number: 700855K
Fix burners that won't turn on or heat up with this burner switch kit. Includes mounting hardware and instructions. Easy 30-minute DIY repair.
This part fixes the following symptoms
-
Won't start
-
Element will not heat
See more...
Do-It-Yourself Stories from Customers like You
The burner switches were not controlling the burners correctly specifically the lo temps were too high the switch knobs were also worn Frank C. • Sunset Beach , NC • December 24, 2019
1) I installed 4 ea new Whirlpool 700855K switches. (The old switches had INF-240P-871 stamped on them. 700855K was the cross-referenced P/N.)
The installation was easy. There is slight difference in the terminal arrangement: 1) the old switch has raised terminals whereas the new switch has recessed terminals (for safety), and 2) the terminal markings are slightly different: The old switch has L1/L2/P/H1/H2 (5 terminals). The new switch has L1/L2/P/HC/H1(Also five terminals. I saw where one...
Read more
More
$84.40
- Compare At:
-
$100.44
- You Save:
-
$16.04
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10312185
Burner stuck on high heat or won't regulate temperature? This infinite switch restores precise control. Straightforward DIY repair with a screwdriver.
Do-It-Yourself Stories from Customers like You
Bad oven knob sensor was causing circuit breaker to trip Kelly V. • Rockaway , NJ • December 27, 2019
Replacing the oven knob sensor was easy. Figuring out it was the sensor causing the circuit breaker to trip was the challenge.
Read more
More
$87.35
- Compare At:
-
$103.95
- You Save:
-
$16.60