Med Small Engine Start Switch Parts
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3395382
The Start Switch is an OEM replacement part for Whirlpool dryers. It is an electronic component responsible for initiating the heating elements and tumble cycles upon user command from the control panel.
Causes of a bad start switch involve general wear over extended use. Failure of the internal conducting surfaces interrupts circuit activation as well.
Symptoms of a bad start switch include:
- Heating elements or tumble cycles that will not engage properly
- Dryer fails to operate or stops mid-cycle unexpectedly
- Control panel appears non-responsive to selections
- Error codes related to ignition or power delivery faults
Note: This dryer push-to-start switch has 2 terminals.
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore electric dryer models.
Do-It-Yourself Stories from Customers like You
Dryer wouln't start heard the timer working but the starter wouldn't start Perry B. • Stockton , CA • December 05, 2014
I replaced the starter switch, that really didn't need to be replaced, and the thermal fuse, which did.
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10420741
This push-to-start switch initiates the dryer cycle when the start button is pressed. It sends a signal to the motor and control circuit to begin tumbling and heating. Replace this switch if pressing the start button produces no response, the dryer only runs while you hold the button down, or the switch feels loose or does not click when pressed.
Do-It-Yourself Stories from Customers like You
The push start button didn't start the dryer Kirsten K. • Fayetteville , NC • July 21, 2016
I replaced the part i ordered and it worked great!
Read more
More
Genuine Frigidaire part
By: Frigidaire
Part Number: 134762010
Fix a washer that won't fill, overfills, or shows E35 error code with this water level pressure switch. Moderate DIY repair takes about 1-2 hours.
Do-It-Yourself Stories from Customers like You
E35 Michael B. • Mechanicsville , VA • September 13, 2016
Water valve not closing all the way. Water keep entering washer even with power cord unplugged. Parts I ordered fit perfect. Ordered on Thursday night , parts there Saturday. Great service and shipping. Thank
Read more
More
Genuine Frigidaire part
By: Frigidaire
Part Number: 297286812
This capacitor stores and releases electrical energy to help the refrigerator's compressor start and run smoothly. Replacing a weak or failed capacitor can restore reliable compressor startup and more consistent cooling performance.
- Provides the electrical boost/phase shift needed for compressor motor startup and steady operation
- Works with the start device to deliver proper current to the compressor
- Failure symptoms can include clicking or humming near the compressor, poor cooling, or short cycling
- May cause the compressor not to start after power interruptions when weak or failed
What's included: 1 capacitor Install notes:
- Disconnect power before servicing any electrical component
- Safely discharge the capacitor before handling; avoid touching terminals
- Note wire positions and terminal markings; transfer leads one at a time to the matching terminals
- Secure the capacitor in its mounting/bracket to prevent vibration damage
Do-It-Yourself Stories from Customers like You
Three year old Frigidaire upright freezer quit running. Kenneth B. • Crossville , TN • April 03, 2021
My barely three year old Frigidaire upright freezer quit running and we discovered it when most of the contents were just starting to thaw. Luckily we have nearby neighbors that my wife walks with most days and two or three of them came to our rescue with available freezer space to save the more valuable things like meat and seafood. The compressor would not come on, no fan, no noises of any kind but the light came on when the door was opened so obviously it had power. I unplugged it for a...
Read more
More
Genuine Ge part
By: Ge
Part Number: WB24T10022
Burner not heating or stuck on? This surface element switch controls power to your cooktop burners. Common repair when heat won't adjust properly.
Do-It-Yourself Stories from Customers like You
Burner didn't work Larry W. • Aiea , HI • March 23, 2014
Replaced the switch infin by watching the video
Read more
More
Genuine Bosch part
By: Bosch
Part Number: 00165256
Dishwasher won't fill or keeps overfilling? The float switch detects water levels for proper filling and draining. Accessible repair in under 30 minutes.
This part fixes the following symptoms
-
overflowing
-
Will not fill with water
See more...
Do-It-Yourself Stories from Customers like You
Inlet valve would not open to let water into the dishwasher Kurt J. • Burnsville , MN • January 09, 2015
I checked continuity at the float switch since I knew the inlet valve was working when direct wired to 120v. Switch did not have continuity. Replaced switch and inlet valve worked at start of cycle.
Read more
More
Genuine Ge part
By: Ge
Part Number: WR07X10084
Fridge clicking but not cooling? A faulty compressor start relay prevents startup. This part restores cooling in 15-20 minutes. Includes installation video.
Do-It-Yourself Stories from Customers like You
We had no power only lights on Frank A. • Smithtown , NY • January 28, 2022
GE refrigerator 12 years old and we love it. Ordered compressor overload and compressor start relay video's were great made the replacement easy. I also ordered the control board because I felt this was the real culprit again the video was the best. With all the parts replaced GE profile refrigerator has been working like new. Thank you AppliancePartsPro.com
Read more
More
Genuine Ge part
By: Ge
Part Number: WB24X10146
The Micro Switch is an OEM part for GE microwaves. This part ensures the appliance operates only when the door is securely closed. It controls the electrical circuit, allowing the microwave to start heating food when the door latch engages the switch.
Causes of a bad micro switch can include wear and tear from frequent use, electrical issues, or physical damage from slamming the microwave door.
Symptoms of a bad micro switch include:
- The microwave not starting or stopping unexpectedly
- The microwave running even with the door open
- Intermittent power issues
- The door not latching or the microwave indicating the door is open
This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Stopped working tripped breaker Roberto M. • Pembroke Pines , FL • March 08, 2019
By replacing the switches.
Read more
More
Genuine Ge part
By: Ge
Part Number: WB24T10063
Fix a burner stuck on high or not heating with this infinite control switch. Common cause when burners won't adjust temperature. DIY repair in 20 minutes.
Do-It-Yourself Stories from Customers like You
Burner only worked on high setting Alejandro G. • East Meadow , NY • February 15, 2016
Ordered recommended part for GE appliance. Change was very simple. Followed instructions on video and removed one wire at a time. Very easy to change 5 to 10 minutes.
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10312185
Burner stuck on high heat or won't regulate temperature? This infinite switch restores precise control. Straightforward DIY repair with a screwdriver.
Do-It-Yourself Stories from Customers like You
Bad oven knob sensor was causing circuit breaker to trip Kelly V. • Rockaway , NJ • December 27, 2019
Replacing the oven knob sensor was easy. Figuring out it was the sensor causing the circuit breaker to trip was the challenge.
Read more
More
Genuine Ge part
By: Ge
Part Number: WE4M255
Fix a dryer timer that won't advance or automatic cycles that stopped working. This timer resistor regulates cycle duration. Easy 15-minute repair.
Do-It-Yourself Stories from Customers like You
Dryer would not shut off at end of any cycle Jeffrey S. • Davis , CA • January 15, 2018
I Replaced the power resistor. The old resistor had a small burnt spot and tested infinity for resistance.The terminals were too small so I had to make new connector. Any 5000 ohm ceramic filled resistor would have worked also.
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: 700855K
Fix burners that won't turn on or heat up with this burner switch kit. Includes mounting hardware and instructions. Easy 30-minute DIY repair.
This part fixes the following symptoms
-
Won't start
-
Element will not heat
See more...
Do-It-Yourself Stories from Customers like You
The burner switches were not controlling the burners correctly specifically the lo temps were too high the switch knobs were also worn Frank C. • Sunset Beach , NC • December 24, 2019
1) I installed 4 ea new Whirlpool 700855K switches. (The old switches had INF-240P-871 stamped on them. 700855K was the cross-referenced P/N.)
The installation was easy. There is slight difference in the terminal arrangement: 1) the old switch has raised terminals whereas the new switch has recessed terminals (for safety), and 2) the terminal markings are slightly different: The old switch has L1/L2/P/H1/H2 (5 terminals). The new switch has L1/L2/P/HC/H1(Also five terminals. I saw where one...
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: W10339251
Fix a washer that overfills, won't fill to the right level, or floods. This water level pressure switch monitors tub water. DIY install in 1 hour.
Do-It-Yourself Stories from Customers like You
Water level control wouldn't work Micheal W. • Millville , UT • April 11, 2014
I replaced it and the new one fit perfectly. reassembled and fired it up. Worked as desired, like new...
Read more
More
Genuine Ge part
By: Ge
Part Number: WE4X448
The Flame Sensor is an OEM part for GE dryers. This part detects the presence of a flame in gas dryers, ensuring that the gas ignites properly for safe and efficient drying.
Causes of a bad flame sensor can include regular wear and tear, carbon buildup from the gas flame, or electrical malfunctions.
Symptoms of a bad flame sensor include:
- The dryer not heating or taking longer to dry clothes
- The dryer shutting off unexpectedly during a cycle
- The igniter glowing but not igniting the gas
- Error codes related to heating or ignition issues
This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.
This part fixes the following symptoms
-
No heat or not enough heat
See more...
Do-It-Yourself Stories from Customers like You
Dryer heating for only a short time then no heat at all David N. • Fairfax , CA • December 08, 2018
GE Gas Dryer Model DBVH512GF1WW began to heat for only a short amount of time so drying clothes took WAY too long. Read online that the first thing to replace are the solenoids. Bought the two solenoids from AppliancePartsPros.com for about $50 total, and it seems to have fixed the problem. Had to watch a few videos to learn to disassemble the dryer, and the job took a couple of hours, but now that I know what I'm doing it could be done in less than 30 minutes.
Also, the old solenoids tested...
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10411934
Fix burners stuck on high or heating out of control with this infinite switch. Controls single, dual, or triple element burners. Easy DIY repair.
Do-It-Yourself Stories from Customers like You
Front two burners were heating out of control Garrey P. • Rogers , TX • December 11, 2018
Replaced two switches that controlled two front burners. One controlled three different burner sizes options in one burner. The other was the speed burner, basically three different burner options in one burner.
Read more
More
Genuine Ge part
By: Ge
Part Number: WC21X20249
The Return Switch is an OEM part for GE trash compactors. This part ensures that the compacting ram returns to its starting position after each compaction cycle.
Causes of a malfunctioning return switch can vary from electrical issues, such as short circuits or worn-out connections, to mechanical problems, including physical damage from wear and tear or blockages preventing the switch's activation.
Symptoms of a faulty Return Switch include:
- The compactor ram fails to return to its original position after a compaction cycle.
- The unit does not start or operate correctly, indicating issues with the cycle initiation.
- Unusual noises or behavior from the trash compactor, suggesting that the ram is not aligning or moving as expected.
This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.
Do-It-Yourself Stories from Customers like You
The trash compactor would not cycle without me holding kick plate up for whole cycle when it did get back to the top of the cycle it would only stop if i opened the door Mike D. • Pine Mountain , GA • December 15, 2014
TALKED TO YOUR REPRESENTATIVE AND WE WENT THROUGH ALL THE ON/OFF AND LIMIT SWITCHS. NARROWED IT DOWN TO TWO SWITCHS. THE ON/OFF SWITCH AND THE LIMIT SWITCH ON THE DOWN CYCLE SIDE. REPLACED ON/OFF AND DETERMINED THAT THAT WAS NOT THE ISSUE. THEN UNCOVERED LIMIT SWITCHS AND REPLACE DOWN SWITCH, FIXING THE PROBLEM
Read more
More