Super Egg Small Engine Start Switch Parts
Genuine Whirlpool part
By: Whirlpool
Part Number: WP207166
Washer won't start or keeps blowing fuses? The lid check switch ensures your washer only runs when the lid is closed. Easy DIY repair in under 30 minutes.
This part fixes the following symptoms
-
Will not fill with water
-
Will not agitate
See more...
Do-It-Yourself Stories from Customers like You
My washer stopped it just sttoped working Charles T. • Houston , TX • February 01, 2015
First I needed to replaced the timer. However that timer is no longer available. So I was not able to buy that part. A friend encouraged me to cross reference the part number. I did and I found another timer that claimed it would work on my machine. It looked very similar. I got the timer from you guys and put it in. The water valves worked right away but the motor did not. I researched more troubleshooting ideas and discovered I had a bad lid check switch. I got a new one of those from you...
Read more
More
$45.30
- Compare At:
-
$54.36
- You Save:
-
$9.06
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3395382
The Start Switch is an OEM replacement part for Whirlpool dryers. It is an electronic component responsible for initiating the heating elements and tumble cycles upon user command from the control panel.
Causes of a bad start switch involve general wear over extended use. Failure of the internal conducting surfaces interrupts circuit activation as well.
Symptoms of a bad start switch include:
- Heating elements or tumble cycles that will not engage properly
- Dryer fails to operate or stops mid-cycle unexpectedly
- Control panel appears non-responsive to selections
- Error codes related to ignition or power delivery faults
Note: This dryer push-to-start switch has 2 terminals.
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore electric dryer models.
Do-It-Yourself Stories from Customers like You
Dryer wouln't start heard the timer working but the starter wouldn't start Perry B. • Stockton , CA • December 05, 2014
I replaced the starter switch, that really didn't need to be replaced, and the thermal fuse, which did.
Read more
More
$50.57
- Compare At:
-
$60.18
- You Save:
-
$9.61
Genuine Frigidaire part
By: Frigidaire
Part Number: 297237702
Compressor clicks but won't start? Replace the start relay when your freezer stops cooling or the compressor shuts off after a few seconds. Quick fix.
Do-It-Yourself Stories from Customers like You
Refrigerator quit cooling Mitchell M. • Jackson , GA • May 12, 2017
First I have an LG French Door with a bottom freezer. It quit cooling. I went on line and watched some very informative You Tube videos. I trouble shot according to these videos. In these videos it shows that if there is a click coming off the compressor it has too meanings, the compressor is froze or the start relay is bad. I ohmed the compressor and had no open wires in the compressor. I then shook the relay and it was making noise. The videos stated that is there is a noise in the relay...
Read more
More
$79.95
- Compare At:
-
$95.94
- You Save:
-
$15.99
Genuine Whirlpool part
By: Whirlpool
Part Number: W11120791
Burner stuck on high or won't turn off? This burner control switch regulates heat settings. Moderate DIY repair—label wires before swapping.
Do-It-Yourself Stories from Customers like You
Burner only worked on high Thom R. • Bowdoin , ME • February 12, 2016
If one control starts to fail the rest are sure to follow soon - so I replaced all four on our JennAir S160. Looked up the parts on line. Due to my background as an aviation electrician in the Navy and then working as an electrical systems designer for a defense contractor the toughest part was the clean up. Oh Well.
Read more
More
$78.27
- Compare At:
-
$93.14
- You Save:
-
$14.87
Genuine Frigidaire part
By: Frigidaire
Part Number: 134762010
Fix a washer that won't fill, overfills, or shows E35 error code with this water level pressure switch. Moderate DIY repair takes about 1-2 hours.
Do-It-Yourself Stories from Customers like You
E35 Michael B. • Mechanicsville , VA • September 13, 2016
Water valve not closing all the way. Water keep entering washer even with power cord unplugged. Parts I ordered fit perfect. Ordered on Thursday night , parts there Saturday. Great service and shipping. Thank
Read more
More
$45.95
- Compare At:
-
$60.39
- You Save:
-
$14.44
Genuine Ge part
By: Ge
Part Number: WB24T10063
Fix a burner stuck on high or not heating with this infinite control switch. Common cause when burners won't adjust temperature. DIY repair in 20 minutes.
Do-It-Yourself Stories from Customers like You
Burner only worked on high setting Alejandro G. • East Meadow , NY • February 15, 2016
Ordered recommended part for GE appliance. Change was very simple. Followed instructions on video and removed one wire at a time. Very easy to change 5 to 10 minutes.
Read more
More
$85.37
- Compare At:
-
$101.59
- You Save:
-
$16.22
Genuine Frigidaire part
By: Frigidaire
Part Number: 318191023
If your dual burner stays on low and won't turn off, or the small element doesn't heat, this infinite switch may need replacing. DIY-friendly repair.
Do-It-Yourself Stories from Customers like You
Large element was very erratic on temperature low/high. Rodney C. • Lake Wales , FL • March 01, 2018
Replaced the infinite, dual, switch. Very good instructional video for Safety, removal * install.
Read more
More
$56.61
- Compare At:
-
$67.37
- You Save:
-
$10.76
Genuine Whirlpool part
By: Whirlpool
Part Number: W10339251
Fix a washer that overfills, won't fill to the right level, or floods. This water level pressure switch monitors tub water. DIY install in 1 hour.
Do-It-Yourself Stories from Customers like You
Water level control wouldn't work Micheal W. • Millville , UT • April 11, 2014
I replaced it and the new one fit perfectly. reassembled and fired it up. Worked as desired, like new...
Read more
More
$130.95
- Compare At:
-
$155.83
- You Save:
-
$24.88
Genuine Ge part
By: Ge
Part Number: WR23X29161
The Door Light Switch is an OEM part for GE refrigerators. It is designed to control the interior light of the refrigerator, turning it on when the door is opened and off when the door is closed.
Causes of a bad door light switch can include wear and tear over time, electrical malfunctions, or physical damage from regular use. A faulty switch can lead to improper functioning of the refrigerator light, impacting visibility inside the unit.
Symptoms of a bad Door Light Switch include:
- Refrigerator light not turning on or off correctly
- Light flickering or remaining dim
- Light staying on even when the door is closed
This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Door light switches malfunctioning Brian R. • Hoover , AL • July 05, 2025
Used video posted by this site on YouTube. Very quick and straightforward replacement.
Read more
More
$30.95
- Compare At:
-
$36.83
- You Save:
-
$5.88
Genuine Ge part
By: Ge
Part Number: WC21X20249
The Return Switch is an OEM part for GE trash compactors. This part ensures that the compacting ram returns to its starting position after each compaction cycle.
Causes of a malfunctioning return switch can vary from electrical issues, such as short circuits or worn-out connections, to mechanical problems, including physical damage from wear and tear or blockages preventing the switch's activation.
Symptoms of a faulty Return Switch include:
- The compactor ram fails to return to its original position after a compaction cycle.
- The unit does not start or operate correctly, indicating issues with the cycle initiation.
- Unusual noises or behavior from the trash compactor, suggesting that the ram is not aligning or moving as expected.
This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.
Do-It-Yourself Stories from Customers like You
The trash compactor would not cycle without me holding kick plate up for whole cycle when it did get back to the top of the cycle it would only stop if i opened the door Mike D. • Pine Mountain , GA • December 15, 2014
TALKED TO YOUR REPRESENTATIVE AND WE WENT THROUGH ALL THE ON/OFF AND LIMIT SWITCHS. NARROWED IT DOWN TO TWO SWITCHS. THE ON/OFF SWITCH AND THE LIMIT SWITCH ON THE DOWN CYCLE SIDE. REPLACED ON/OFF AND DETERMINED THAT THAT WAS NOT THE ISSUE. THEN UNCOVERED LIMIT SWITCHS AND REPLACE DOWN SWITCH, FIXING THE PROBLEM
Read more
More
$10.79
- Compare At:
-
$12.95
- You Save:
-
$2.16
Genuine Ge part
By: Ge
Part Number: WH12X10498
Fix a washer that won't fill with hot or cold water. This rotary temperature switch controls water temperature settings. Easy 5-minute DIY repair.
This part fixes the following symptoms
-
No hot or cold water
-
Will not fill with water
See more...
Do-It-Yourself Stories from Customers like You
No hot water would fill the washer in any cycle or temperature setting if the temperature setting was set to "hot" absolutely nothing would happen when turned on (cold washes worked fine) William H. • St Louis , MO • December 30, 2014
Replaced the water temperature selector switch. After watching a YouTube video for our GE top loading washer showing the switch replacement, I replace the switch in under 5 minutes! Very easy!
Read more
More
$18.95
- Compare At:
-
$22.36
- You Save:
-
$3.41
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10420741
This push-to-start switch initiates the dryer cycle when the start button is pressed. It sends a signal to the motor and control circuit to begin tumbling and heating. Replace this switch if pressing the start button produces no response, the dryer only runs while you hold the button down, or the switch feels loose or does not click when pressed.
Do-It-Yourself Stories from Customers like You
The push start button didn't start the dryer Kirsten K. • Fayetteville , NC • July 21, 2016
I replaced the part i ordered and it worked great!
Read more
More
$27.37
- Compare At:
-
$32.30
- You Save:
-
$4.93
Genuine Samsung part
By: Samsung
Part Number: DC96-01703C
Washer overfilling or not filling properly? The water level pressure switch controls fill cycles. Easy 15-minute DIY repair with our video guide.
This part fixes the following symptoms
-
Will not stop filling with water
See more...
Do-It-Yourself Stories from Customers like You
Samsung clothes washer wa456 code ie u6 John D. • Howard Beach , NY • February 28, 2015
This error code indicated faulty water level and wash cycles were exhibiting either no water or too much water. Saw utube vid using this part for this type of problem and so far the repair is working well. Part arrived in 2 days, it was the right part and the machine is working the way its supposed to so I'm very happy. The worst scenario would have been to hire a repair guy to rip me off for a "Johnson Rod" I didn't need.
Read more
More
$82.95
- Compare At:
-
$97.88
- You Save:
-
$14.93
Genuine Frigidaire part
By: Frigidaire
Part Number: 134813601
The Door Switch is an OEM part for Frigidaire dryers. This part ensures that the dryer operates safely by only allowing the machine to run when the door is completely closed. Positioned typically at the door frame, the switch activates when the door is shut, signaling the control system that it's safe to begin the cycle.
Over time, door switches can wear out or become damaged, which can interfere with the normal operation of the dryer.
Symptoms of a faulty Door Switch include:
- The dryer not starting when the door is closed.
- The dryer stopping unexpectedly, which might be due to a loose or faulty switch.
- A lack of the usual "click" sound that indicates the door has latched properly, suggesting the switch isn’t engaging.
- The dryer continuing to run when the door is opened, which poses a significant safety risk.
This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Dryer will start, run for a few second, then turn off. No error codes John M. • Waikoloa , HI • April 03, 2014
By reading the forums I first thought it may be the thermostat. I bypassed the thermostat wiring and the dryer still turned off after a few second of running. The second check was for the door switch. I couldn't find an explanation of how to bypass, so I just ordered a new one to try. It worked.
Read more
More
$33.95
- Compare At:
-
$40.40
- You Save:
-
$6.45
Genuine Bosch part
By: Bosch
Part Number: 00422748
The Potentiometer is an OEM replacement part for Bosch gas range or cooktops. It functions as a three-terminal resistor that adjusts the flow of electric current, which in turn, controls the ignition and temperature of the cooktop. This component is essential for the precise operation and control of the gas burners, ensuring they light up and maintain the desired flame intensity.
Causes of a malfunctioning Potentiometer can be attributed to wear and tear, electrical issues, or damage due to spills and cleaning products. A compromised potentiometer affects the flow of electric current, leading to issues with the ignition and temperature control of the gas burners.
Symptoms of a bad Potentiometer include:
- The cooktop not lighting or staying lit
- The ignitor continuously clicking without igniting the burner
- Inability to adjust the flame intensity or temperature accurately
This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.
Do-It-Yourself Stories from Customers like You
One burner on my thermador cooktop (pcs484ccus) would not light Kinn K. • Haslet , TX • June 08, 2015
After watching a youtube video, I disassembled the front cover on the cooktop (be sure to turn off the power supply). I then switched the potentiometers on two burners. The burner that was not working now worked and the burner that did work did not. Easy to find the culprit....ordered a new potentiometer from here and though I only got regular shipping, it was actually delivered the NEXT DAY! 5 minutes, put in the new part, and all burners work. Great site, thanks for the help!
Read more
More
$56.95
- Compare At:
-
$67.77
- You Save:
-
$10.82
Genuine Whirlpool part
By: Whirlpool
Part Number: W11120795
Fix a burner that won't heat, stays hot, or can't adjust temperature. This infinite switch controls power levels. Simple DIY repair in 5-10 minutes.
Do-It-Yourself Stories from Customers like You
Stem broke off on surface unit switch Robert Z. • Hampstead , MD • July 09, 2016
Replaced switch with a new one. also replaced the 4 knobs
Read more
More
$73.95
- Compare At:
-
$88.00
- You Save:
-
$14.05