Need Help?
Call
Traps grease and particles from cooking to maintain efficient ventilation. Replace every 6-12 months depending on usage. Confirm fit with your model number.
Ordered all the parts needed, replaced them and the Jenn Air worked just fine. Read more
Fix burners that won't turn on or heat up with this burner switch kit. Includes mounting hardware and instructions. Easy 30-minute DIY repair.
1) I installed 4 ea new Whirlpool 700855K switches. (The old switches had INF-240P-871 stamped on them. 700855K was the cross-referenced P/N.) The installation was easy. There is slight difference in the terminal arrangement: 1) the old switch has raised terminals whereas the new switch has recessed terminals (for safety), and 2) the terminal markings are slightly different: The old switch has L1/L2/P/H1/H2 (5 terminals). The new switch has L1/L2/P/HC/H1(Also five terminals. I saw where one... Read more
Replacement 10-32 machine screw for securing panels, brackets, and internal components. Ideal for replacing missing, stripped, or damaged hardware.
Ordered Bake Element, Y04100019 (Whirlpool AP4283614) to replace a broken bake element on my 30-year old Jenn-Air Model S125 Downdraft Slide-in electric range. Received the element very quickly but it had been damaged in shipping. Called AppliancePartsPros to report this and they quickly shipped another element - very easy process. To install the element, I turned off the power to the range, put on rubber gloves (just in case) and removed the two sheet metal crews at the rear of the oven -... Read more
Replace worn, cracked, or faded burner control knobs on your cooktop. Restores clear temperature markings and secure grip for adjusting heat settings.
This factory screw secures appliance components to their mounting points. Replace missing, worn, or stripped hardware to restore a tight fit, proper alignment, and quieter operation across the affected assembly.
This terminal block provides an insulated, secure junction for incoming power or harness leads inside the appliance. Replacing a cracked, loose, or heat-damaged block restores a safe, reliable connection and helps prevent arcing or intermittent power.
I completely disassembled the entire unit sandblasted repainted with epoxy paint and reassembled. bought a few new parts and its like new again this unit is no longer available and its built into my boat. Read more
This blower wheel mounts on the drive motor and pushes air through the dryer drum and out the exhaust. Replacing a worn wheel restores proper airflow for consistent drying and helps prevent overheating and nuisance shutdowns. What it does:
I replaced the downdraft fan and fan motor of my 25 year old JennAire C301 cooktop. The issue was getting the fan/motor assembly out in such a tight place. I had to first remove the fan cover, cut the wires, then the assembly came out. Putting back wasn't as tough although getting the cover back on (over the motor) was a bit of a strain. Wired it back, turned it on, and was thrilled. Now I'll replace the knobs and burners and we're back in business. Read more
This motor isolator is a vibration-damping grommet that cushions the motor mount to reduce noise and prevent metal-to-metal contact. Replacing worn isolators helps keep the motor seated correctly and the appliance running quieter and smoother.
Ordered three isolators and changed all of them. Sounds like new. Read more
Screw: 8-16 x 3/8 inch.
Sheet metal pan head screw secures panels, brackets, and components to appliance cabinets. Replace missing, stripped, or corroded screws to restore fit.
Replaced burners and cleaned Read more
Gas valve shaft seal.
I replaced the igniter harness and the missing igniter shaft seal with parts from appliancepartspros.com Read more
This locknut is a small threaded retaining nut used to secure rotating and stationary appliance components, helping keep assemblies tight and stable during operation. It prevents parts from loosening and reduces vibration-related issues. What it does:
Stamped metal retaining clip that secures screws to panels and trim. Replace if clip is bent, broken, or missing to properly fasten covers and components.
This burner ring cap base provides the support and alignment for a gas cooktop burner cap, helping direct the flame for consistent heating and safe operation. It replaces damaged or warped bases that prevent proper burner seating. What it does:
Fix a downdraft fan that stops working, vibrates excessively, or cycles on and off. This blower motor replacement takes 1-2 hours to install.
Usually ships within 4 - 14 days
Pop rivet secures sheet-metal panels, brackets, and burner jar lids on appliances. Replace missing, drilled-out, or damaged rivets for permanent hold.
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.