Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Rubber foot that attaches to the bottom of cooktop grates. Replace if cracked, worn, missing, or loose to prevent grates from sliding and scratching.
I removed all the individual burners so I could lift the stainless cover to expose the igniter wires. I cleaned all the wire connections and the 4 good igniters and replaced the one bad igniter. Reassembly was easy and everything worked properly when done. Video of repair was helpful and all parts ordered were correct and shipped promptly and I will definitely use AppliancePartsPros again. Read more
Fix burners that won't ignite or spark continuously. This spark module controls ignition for all surface burners. DIY repair in about 45 minutes.
Refer to Mynor T. of Draper, UT Aug. 12, 2018 write-up. I benefited greatly from the above write-up. It took me a little less time to perform this repair (excluding cleaning the assembly) due to the write-up. This GE Profile gas burner cook top is a “drop-in” model meant to be installed into counter top cut outs. The glass top edges are the actual support area for the entire cook top assembly. The burner bases (on top of the glass top) are screwed to the metal case enclosure (located beneath... Read more
Gas pressure regulator for cooktops and ranges. Installs on the gas supply line to control flow to burners. Replace if cracked, leaking, or missing.
When I moved in to my new house I noticed there was no regulator, and the gas line was copper tubing. I ordered a regulator and ran 40 of trac pipe to make it up to code. Hooking up the regulator was easy. Read more
Secures the ignition electrode on gas range burners. Replace if burners won't spark, igniter clicks continuously, or clip is corroded or loose. Confirm fit with your model number.
Replaced spark module and all electrodes/igniters. Read more
Burner won't light or clicking with no spark? This igniter creates the spark to light gas burners. Easy press-fit installation takes 15 minutes.
ST10-16 X 7/16"
Move stove to unplug, remove rear center panel, indentify the two spade connectors that feed the heating element and remove (unplug) them. Remove two screws that hold the element to the inside rear wall of the stove and remove element. Install new element, plug in the previously removed spade connectors, re-install rear center panel, plug range (power) in, move stove back into place and enjoy. Read more
Black. 8-18 AB HXW 3/8
I ordered the part and was impressed to receive it within two day! I didn't need the screws I ordered (which I ordered just in case) but the trim was put on with no problem and my oven looks brand new again! Thank you! Read more
Liquid propane orifice spud for cooktop and range burners. Regulates gas flow for proper flame. Replace if damaged, worn, or converting from natural gas.
This hold-down bracket secures a designated component inside your appliance, keeping it firmly anchored during use. Replace a bent, broken, or missing bracket to stop movement and rattling and restore proper alignment and a stable, factory fit. What it does:
Ordered new gas valve and new knobs replacing broken. Read more
Seals the gap around your cooktop control shaft to block spills and debris from entering the control area. Replace if worn or damaged. Verify fit.
Burner grate set provides a stable surface for cookware over gas flames. Replace worn, warped, dented, or discolored grates to restore your cooktop.
We bought two new grills for the stove top, and it works like it is new. Read more
Converting your cooktop from natural gas to liquid propane? This LP gas orifice spud enables proper fuel conversion for specific burner positions.
This machine screw is an authentic OEM replacement part sourced directly from the manufacturer. It is used in securing the burner head to the gas range top so that it can be used for cooking. If the burner head becomes loose or the screw is missing, it should be replaced. For safety reasons, the burner should not be used until this screw is replaced; the burner head could shift during cooking and lead to a fire. To start, disconnect the gas and power from the stove to prevent accidental ignition of the burner. Make sure the burners are not hot. Remove the burner grate and burner cap from the burner that is missing a screw. Install the new screw in the hole and tighten it with a screwdriver. Put the burner cap and burner grate back on the stove and reconnect the gas and power. Periodic inspection of the burner heads and all associated screws and parts on the stovetop will prevent accidents and keep the stove working correctly. This screw is a silver, metal part that is sold individually. It is designed for use in gas rangetops manufactured by General Electric and Hotpoint.
Second repair after 10 years of service - igniter had cracked and spill overs were causing the others to misfire. This was a two-step process. I took apart the cooktop to see what parts were neded. Screws were all rusted, I had to drill ome out. The burner gaskets broke during the process and needed replacement. One of the burners had deformed due to excess heat. After that initial diagnose, I reassembled the cooktop without the igniters and ordered all the parts I needed. The second stage was... Read more
Replacement screw for securing panels, brackets, and internal components in ranges, ovens, and cooktops. Replace missing, stripped, or damaged screws.
Burner base installs beneath the burner cap on gas cooktops. Replace if cracked, warped, or dome-shaped to restore proper flame coverage and alignment.
I decided to replace my igniters because I suspected that they were shorted. Due to my recklessness, I was too hard in taking them off and broke a couple. But with Appliance Pro's recommendations, I moved on to treplacing the switch harness assembly. I have to say that the replacement of the switch harness assembly took no more than 30 seconds. It was removing the base burners and the porcelain/cermaic igniters from their bases that took forever. Just a heads up to those amateurs like me, be... Read more
Burner base for gas cooktops, secures to cooktop surface and holds igniter assembly. Replace if cracked, broken, or damaged during repairs.