Ei30bm55hc Parts

The Grease Filter is an OEM replacement part for Frigidaire microwaves. It traps grease-laden smoke and particles released from cooking. Color: silver. Measures about 6 inches wide by 8 inches deep.

Causes of a bad grease filter can include clogging from accumulated grease and debris, physical damage from cleaning or handling, or wear and tear over time. A clogged or damaged filter can reduce the efficiency of the range hood, leading to poor ventilation and potential damage to the range hood motor.

Symptoms of a bad grease filter include:

• Reduced airflow or suction
• Excessive smoke or odors during cooking
• Grease buildup on kitchen surfaces
• Visible damage or clogging of the filter

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Door Switch is an OEM replacement part for Frigidaire wall ovens. It is a component located on the oven door that detects when the door is opened and closed. The door switch works alongside the control board to regulate oven operations based on door position.  

Symptoms of a bad door switch can include:

• Oven failing to automatically go into bake or warm modes after door closure
• Interior lights not turning on when the door is opened
• Control buttons/display remaining constantly lit instead of dimming
• Oven not heating or functioning properly in different modes

Causes relate to normal wear over extended use as the door switch mechanism cycles with frequent door openings and closings. Moisture exposure or impacts could also degrade switch performance.

This OEM Frigidaire switch is compatible with Amana, Jenn-Air, KitchenAid, and some Electrolux wall oven models as well.

This microwave magnetron generates the energy that heats food in the oven cavity. Replacing a failed magnetron often restores normal heating.

• Produces microwave energy to heat food inside the cavity
• Typical failure symptom: microwave runs but does not heat
• Can cause loud humming or buzzing during operation
• May trip a breaker or blow a fuse at the start of a cook cycle

• Disconnect power before servicing; for built-in/OTR units, switch off the circuit breaker.
• The high-voltage capacitor can retain a dangerous charge—discharge it using the proper service procedure.
• Handle the ceramic antenna/insulator carefully and avoid overtightening mounting screws.
• Reinstall airflow shrouds/ducts and transfer any reusable brackets or thermal devices from the original part as required.

This glass turntable tray provides a stable, heat-resistant surface that rotates food inside the microwave for more even cooking and reheating. It replaces a damaged or missing tray to restore proper rotation and support. What it does:

• Supports plates, bowls and containers while the microwave's turntable motor rotates them for even heating.
• Transfers rotation from the drive coupling through the roller/guide assembly to the glass tray.
• Restores stable, level rotation when the original tray is cracked, chipped, or missing.
• Helps prevent food spills inside the cavity by providing a flat, easy-to-clean surface.

• One glass turntable tray.

• Handle the glass carefully to avoid chips or cracks; wear gloves if necessary.
• Place tray onto the roller/guide and align with the drive coupling; it turns freely before use.
• Clean with mild detergent and non-abrasive cloth; do not use if the glass is cracked or severely chipped.
• If rotation problems persist after replacing the tray, check the roller/guide and drive coupling for wear.

This door latch spring restores the return tension in your microwave's door release mechanism so the latch engages and releases correctly. Replacing a fatigued or broken spring helps ensure safe door operation and reliable interlock switch activation.

• Provides the return force for the latch lever/door release button
• Helps door hooks engage fully and release smoothly
• Supports proper interlock switch actuation so the unit will run only when the door is closed
• Typical failure signs: door won't latch, "open/close door" error, door button sticks, or needing to hold the door shut to start

• Disconnect power. Microwaves can retain dangerous high voltage even when unplugged; discharge the capacitor
• Access the latch assembly behind the control panel; note the spring's orientation and attachment points
• Use needle-nose pliers to install without overstretching; inspect the latch lever and door hooks for wear
• Verify proper door closure and interlock switch operation before reassembly

This end cap finishes and secures the exposed end of a handle, rail, or trim piece on your appliance. It restores a clean look and helps keep the attached component stable during everyday use.

• Covers the open end of a handle/rail and conceals fasteners for a finished appearance
• Helps hold the mating piece in place to reduce looseness, rattling, or wobble
• Replace if the existing cap is cracked, missing, warped, or will not stay attached
• Can help address issues like a loose handle/rail, exposed screws, or sharp/unfinished edges

• Disconnect power to the appliance before servicing; shut off gas/water if applicable
• Note the cap's orientation and any side-specific features before removal
• Release retaining tabs or remove the set screw (as applicable), then align and press/fasten the new cap into place
• Do not overtighten fasteners; verify secure fit and smooth operation after installation

This rectifier is the microwave's high-voltage diode. It converts AC to DC in the high-voltage circuit so the magnetron can heat. Replacing a failed rectifier can restore reliable heating performance.

• Converts alternating current to direct current in the microwave's high-voltage circuit
• Works with the transformer and capacitor to power the magnetron
• A failed rectifier can cause no heat while the unit runs, intermittent heating, or unusual humming
• Blocks reverse voltage to help protect high-voltage components

• Disconnect power before servicing; microwaves contain high-voltage circuits
• The high-voltage capacitor can retain a dangerous charge even when unplugged—discharge per service procedures
• Observe polarity and match the original orientation during installation
• Route and secure leads as originally installed to avoid arcing or damage

This replacement end cap finishes and secures the open end of a compatible handle, rail, or trim piece on your appliance. Replacing a cracked or missing cap restores a clean look and helps keep the attached part properly aligned. What it does:

• Covers and protects the exposed end of the mating bar/handle/trim
• Helps keep the connected component seated and prevents shifting
• Replaces broken or missing caps that won't stay attached
• Common signs: loose or wobbly trim/rail, rattling, visible broken tabs, or an uncovered edge

• 1 end cap

• Disconnect power to the appliance before servicing
• Compare the new cap to the original to match orientation
• Transfer and reuse any original screws or clips if your model uses them
• Align tabs and press or slide the cap into place without forcing; verify a secure fit

Compressor start capacitor that helps the refrigerator compressor start reliably so the appliance can maintain proper cooling. Replace a weak or failed capacitor to reduce hard-starting, excessive humming, or loss of cooling. What it does:

• Provides the starting boost the compressor needs to reach running speed.
• Commonly linked to symptoms like compressor humming but not starting, warm refrigerator, or frequent on/off cycling.
• Works with the compressor start circuit; a failed capacitor can prevent the compressor from starting.
• Visible damage, leakage, or failed electrical tests indicate replacement is needed.

• Disconnect power to the appliance before accessing the capacitor.
• Discharge the capacitor before touching terminals to avoid shock.
• Note wire locations or photograph connections before removal; reconnect wires exactly.

Replacement screw used to secure panels, trim, and internal components in Frigidaire appliances. Restores proper fit after repairs and helps eliminate rattling or loose parts for safer, quieter operation. What it does:

• Secures panels, brackets, and trim to maintain correct alignment and fit
• Prevents vibration and rattling caused by loose or missing fasteners
• Use when original screw is missing, stripped, or damaged
• Matches common fastener locations on affected Frigidaire appliances

• Disconnect power and water before starting any repair
• Use the correct driver to avoid stripping the screw head; hand-start to ensure alignment
• Do not overtighten; tighten until snug to avoid damaging threads or plastic parts

A replacement unified-thread screw used to secure appliance panels and internal components. Provides a direct fastener to restore secure attachment when original screws are missing, damaged, or corroded. What it does:

• Fastens panels, brackets, trim pieces, and other appliance components that use a unified-thread screw.
• Restores secure mounting to reduce rattling, movement, or misalignment of parts.
• Replaces stripped, rusted, or missing screws to help maintain safe operation.
• Works where the appliance's service manual or parts diagram specifies a unified-thread fastening point.

• Disconnect power and water before servicing for safety.
• Use the correct screwdriver or bit to avoid stripping the head; install by hand until started, then snug—do not overtighten.
• Replace like-for-like: match thread type and length to the removed screw to ensure proper fit and function.
• If other fasteners show corrosion or damage, inspect nearby hardware and replace as needed.

This is a replacement mounting screw used to secure panels, trim, and small components in compatible appliances. Installing the correct screw restores a secure fit and helps stop rattling or loose parts. What it does:

• Secures panels, brackets, trim pieces or small assemblies to the appliance frame
• Prevents parts from shifting, vibrating, or producing rattling noises when in place
• Replaces missing, worn, or stripped fasteners that cause loose doors or misaligned trim
• Works with the original mounting points and thread types used by the manufacturer

• Always disconnect power or unplug the appliance before servicing to avoid electrical hazard.
• Use the correct screwdriver or bit to avoid stripping the head; do not overtighten.
• Keep track of small parts and compare the new screw to the old one before installation.

This interior refrigerator lamp provides reliable lighting inside the fresh-food compartment so you can see contents clearly. It replaces a dim or non-working lamp to restore normal interior illumination. What it does:

• Provides interior lighting for the refrigerator compartment
• Replaces a burned-out, flickering, or intermittently working lamp
• Helps you find food and check expiration labels without opening the compartment longer than necessary
• Works with the existing lamp housing and socket when compatible

• One interior refrigerator lamp

• Disconnect power to the appliance before replacing the lamp to avoid electrical shock
• Allow the lamp and surrounding area to cool before handling
• Handle the lamp carefully to avoid breakage; dispose of broken bulbs per local regulations
• Check the socket and appliance light switch for faults if the lamp does not light after installation.

This replacement frame restores the appliance's outer trim and helps hold the control/door area together for a clean, finished appearance. It's a direct-fit exterior trim piece that replaces damaged or worn frames. What it does:

• Replaces a cracked, chipped, warped or bent trim/frame that affects appearance
• Secures and aligns the surrounding control or door components to reduce gaps and rattles
• Covers internal edges to help keep out dust, moisture and debris
• Restores the original look after impact or wear

• Disconnect power to the appliance before starting any repair
• Remove required trim, screws or clips to access and replace the frame; keep fasteners for reuse unless damaged
• Handle edges carefully—trim pieces can be sharp; use proper hand protection

This damper assembly controls airflow between the freezer and refrigerator compartments to help maintain even temperatures. Replaces a faulty damper to restore proper cold-air distribution and reduce temperature imbalances. What it does:

• Opens and closes to regulate cold air flow from the freezer into the fresh-food compartment.
• Commonly used when the refrigerator section is too warm while the freezer remains cold.
• Can stop excessive air flow that causes frost build-up or noisy operation.
• Works with the fridge's control system to modulate compartment temperatures.

• One damper assembly

• Disconnect power before starting work to avoid electrical hazard.
• Access typically through the fresh-food or freezer interior; remove panels as needed.
• Handle the actuator and wiring carefully; ensure connectors are fully seated.
• Test operation after installation and reassemble panels securely.