Mah6700a Parts

The Door Switch Assembly is an OEM part for Whirlpool washing machines. This assembly detects whether the washer door is open or closed, allowing the machine to start or stop the washing cycle accordingly.

Causes of a bad door switch assembly can include wear and tear from frequent use, damage from forceful closing of the door, or electrical issues. A malfunctioning switch can prevent the washer from recognizing a closed door, thus hindering the start of the wash cycle or causing it to stop unexpectedly.

Symptoms of a bad Door Switch Assembly include:

• Washer not starting or stopping mid-cycle
• Error codes indicating door issues
• Washer not spinning or agitating
• Door lock mechanism not engaging or disengaging properly

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Hose Clamp is an OEM part for Whirlpool appliances. It secures hoses in place, ensuring a tight connection and preventing leaks in various systems such as washing machines, dishwashers, and refrigerators. This clamp is crucial for maintaining the integrity of the water or air lines it secures.

Causes of a bad hose clamp include wear and tear over time, exposure to water and detergents, or mechanical stress from repeated tightening and loosening.

Symptoms of a bad hose clamp include:

• Leaks at the hose connection points
• Hoses slipping off the connections
• Visible rust or damage on the clamp
• Reduced appliance efficiency due to leaks

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Hose Clamp is an OEM part for Whirlpool washing machines. This clamp secures the hose in place, ensuring a tight connection and preventing leaks during operation. It is essential for maintaining the integrity of the washing machine's water system, securing hoses that carry water to and from the washer.

Common causes of a bad hose clamp include rust, physical damage, or loosening from repeated tightening and loosening.

Symptoms of a bad hose clamp include:

• Water leaks around the hose connection points
• The hose slipping off the fitting
• Visible rust or wear on the clamp
• Difficulty in tightening the clamp to secure the hose

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models.

Restore proper draining with this complete drain pump assembly. It moves water out of the washer during the drain and spin portions of the cycle to prevent standing water, cycle interruptions, and musty odors.

• Pumps wastewater from the tub to the household drain
• Helps prevent standing water and cycle pauses
• Common symptoms: won't drain or drains slowly, humming or grinding from the pump area, leaks at the pump, drain-related error codes
• Direct replacement for a failed or noisy pump assembly

• Disconnect power and shut off water before servicing; have towels or a pan ready for residual water
• Access location varies by model; remove the appropriate lower/front/rear panel to reach the pump
• Transfer wiring and hoses one at a time to the new pump, matching orientation; securely seat clamps and seals
• Inspect and clear the drain hose and filter for debris before reassembly; run a test cycle and check for leaks

This door lever actuates the latch/switch when the door closes. If it's worn or broken, the appliance may not sense a closed door and won't start. Replacing it restores proper door engagement and safe, reliable operation. What it does:

• Engages the door latch/switch mechanism so the control knows the door is closed
• Helps ensure the unit only runs with the door fully shut
• Replaces cracked, bent, or missing levers that prevent proper door sensing
• Common symptoms: won't start, must hold/push door to run, "door open" indicator stays on

• 1 door lever

• Disconnect power before servicing
• Access the latch/switch area; note the original lever's orientation and any spring
• Transfer and reuse existing hardware if needed; install the new lever in the same position
• Close the door and test for proper start/stop operation

This shock absorber stabilizes the washer's tub during spin by absorbing vibration and movement. Replacing a weak damper helps reduce shaking and banging for smoother, quieter cycles and better spin performance.

• Controls tub motion and dampens vibration during acceleration, spin, and braking
• Helps prevent excessive shaking, thumping, and walking
• When worn, can cause loud banging, off-balance interruptions, or longer spin times
• Supports the suspension to reduce stress on hoses and other components

• Disconnect power and turn off water supply before servicing
• Support the tub to relieve load on the damper; remove mounting pins/bolts
• Install the new damper in the same orientation; ensure both ends are fully seated/locked and reuse original hardware if required
• Reassemble panels and run an empty spin test to ensure smooth operation

This drain pump assembly moves water out of the washer during the drain and spin parts of the cycle. Replacing a weak, noisy, or leaking pump restores proper draining, prevents standing water, and helps cycles finish correctly.

• Pumps wastewater from the tub to the household drain
• Supports proper spin performance by clearing water from the tub
• Common symptoms: won't drain or drains slowly; water left in tub; loud humming/grinding from pump area; leaks around the pump; cycle stops with a drain-related error
• A clogged hose or debris in the pump can mimic failure—inspect for obstructions

• Disconnect power and water supply; wear gloves. Bail or wet-vac remaining water and place towels or a pan to catch spills
• Clamp and remove inlet/outlet hoses; note hose orientation and routing
• Move wiring connector(s) one at a time to the new pump and secure the pump in place
• Ensure hoses are clear and clamps tight; run a drain/spin test and check for leaks

Color: Black. For biscuit order 98008169. For white order WP98008544.

This shock absorber mounts between the washer tub and cabinet base to control movement during agitation and spin. Replacing a worn damper restores stability, reducing vibration and noise for smoother, more reliable cycles.

• Cushions and limits tub movement to absorb vibration during spin
• Helps prevent banging, "walking," and excessive shaking
• Supports proper balance so the washer can reach and maintain full spin speed
• Common symptoms of failure: loud thumping, unbalanced/no-spin interruptions, machine moving across the floor

• Disconnect power and turn off water before servicing
• Access shocks per model; support the tub to relieve load before removal
• Reuse existing mounting hardware if applicable; tighten all fasteners securely
• After replacement, level the washer and run a rinse/spin test; consider replacing shocks as a set for even damping

This door boot seal is the flexible gasket that surrounds the front-load washer's door opening. It restores a watertight seal to stop leaks when the original becomes torn, warped, or no longer seats correctly.

• Creates a watertight barrier between the door opening and outer tub
• Prevents water from escaping the front panel during wash and spin
• Helps cushion the door/tub interface to reduce rubbing and wear
• Common symptoms: water leaking at the front, visible tears/cracks, loose or misshapen gasket lip

• Disconnect power and turn off water before servicing
• Remove the outer retaining clamp, peel the old boot from the front panel, then remove the inner clamp from the tub
• Note orientation marks and any hose connections; transfer and seat the new boot evenly
• Reinstall inner and outer clamps securely and verify an even seal before test cycling

This is the hot water inlet valve for compatible laundry appliances. It controls the flow of hot water into the machine during fill cycles, helping ensure proper washing performance and accurate temperature mixing.

• Opens and closes to allow hot water into the tub when energized
• A failed valve can cause no hot fill, slow filling, incorrect water temperature, or leaks from the valve body
• Also lead to error codes related to water fill or extended fill times

• Disconnect power and turn off both water supplies before servicing
• Have a towel/contained pan ready for residual water in hoses
• Note hose orientation and electrical connector position before removal
• Inspect and replace inlet screen washers or hoses if restricted or worn

This cold water inlet valve is the solenoid-operated valve that opens to let cold water into your washer during fill and closes to stop flow. Replacing it restores proper fill speed and helps prevent off-cycle drips.

• Regulates cold-side water flow into the washer during fill and rinse cycles
• Opens when energized by the control; closes to stop water between cycles
• Common signs of failure: no cold fill, slow fill, or dripping into the tub
• May trigger fill/temperature errors or cause a loud hum with little/no water flow

• Disconnect power and shut off the household water supply before servicing
• Place a towel or pan to catch residual water and relieve line pressure
• Label and transfer hoses and wire connectors one-for-one to the new valve
• Inspect/clean inlet screens and flush lines; check for leaks after a test fill

This assembly is the housing the dispenser drawer slides into, restoring a smooth pull-out action and proper dispensing. It supports the drawer and channels water through the detergent, bleach, and fabric softener compartments into the tub.

• Holds and guides the pull-out dispenser drawer
• Routes incoming water through the dispenser cups into the washer
• Helps seal the dispenser opening to minimize drips and leaks
• Common symptoms: leaks at the dispenser, poor detergent/softener dispensing, or a drawer that sticks, jams, or won't seat

• Disconnect power and shut off water before servicing
• Remove the dispenser drawer; remove top/console panels as needed for access
• Detach fill hose(s) and outlet chute; transfer any seals, clips, and fittings to the new housing
• Reassemble and run a short fill/rinse to check for leaks

The Washer Leg Assembly is an essential component for maintaining the stability and functionality of your Samsung washer. Designed to provide secure support, this genuine OEM part ensures your appliance remains level, minimizing vibrations and reducing noise during operation. Crafted with high-quality materials, the Washer Leg Assembly offers durability and reliable performance, helping to extend the lifespan of your washer. Its precise fit guarantees easy installation, allowing you to quickly restore your washer to optimal working condition without the hassle. Compatible with a wide range of Samsung washer models, this leg assembly is the perfect solution for replacing worn or damaged legs. By choosing the Washer Leg Assembly , you invest in a dependable part that enhances the overall efficiency and user experience of your appliance. Whether you're performing routine maintenance or addressing specific issues, this genuine OEM part provides the reassurance of quality and compatibility you need for seamless washer operation.

This hinge guide is the small bushing the hinge pin rides in. It reduces friction and keeps the panel aligned so the door or lid opens smoothly and closes flush for reliable everyday use.

• Provides a low-friction bearing surface for the hinge pin
• Helps maintain door/lid alignment so it closes flush
• Wear can lead to sagging, scraping, squeaking, or binding
• Restores smooth operation and consistent closing when the original is worn

• Disconnect power; shut off water supply
• Support the door or lid before loosening hinge fasteners
• Remove the worn guide and install the new guide on the hinge pin or in the hinge bracket
• Reassemble, then check alignment and smooth open/close

This dispenser hose routes water from the refrigerator's valve to the dispenser and ice maker, helping restore proper water delivery and prevent leaks or drips at the dispenser. Use as a direct replacement for damaged or leaking lines. What it does:

• Carries water from the inlet valve to the dispenser and ice system
• Replaces cracked, split, or kinked tubing that causes leaks
• Can resolve weak or intermittent dispenser flow caused by restricted or collapsed hose
• Helps prevent water damage by restoring a sealed, secure connection

• Shut off the refrigerator's water supply and disconnect power before starting
• Inspect fittings and clamps; replace any corroded or damaged hardware
• Route hose without sharp bends or kinks and secure with proper clamps
• Turn water back on and check all connections for leaks before restoring normal use