6875Ads Parts

I have a Jennair jjw9630cas double wall oven, and after a few years I noticed that the light would not go out, first in the bottom oven, and then in the top oven. After doing some research I discovered this was not uncommon, and the fix usually involved replacing the hinges and/or the hinge receptacles. It didn't look like a difficult fix so I ordered four new hinges and four new receptacles, which arrived quickly. I found a video on YouTube that showed how to replace the hinges and it... Read more

• Oven is too hot
• Little to no heat when baking
• Won't start
• Little to no heat when broiling

First of all Appliance Parts Pros is the best!! I would not have had the confidence to make this repair myself without their outstanding videos and Q&A sections on their website. And their prices for parts are very competitive. Like many stories on the website, my oven would heat up beyond the temperature set point. When it reached the target temperature, the lower heating element (I think this is the “bake” element) would shutoff, but the top element (“broil” element I believe) would remain on... Read more

• Oven is too hot
• Little to no heat when baking
• Won't start
• Oven not heating evenly

Online videos made this seem an easy fix. I unplugged the oven and removed the rear panel, then found where the temp sensor entered the oven. I unplugged the sensor's electric connector. Unlike the videos, this sensor screwed in from the inside of the oven, so I had to remove the 2 screws inside the oven which hold the sensor in place. Then I pulled the sensor out, careful not to tear the insulation with the wires and connector. Then I just pushed the new connector through the same hole and... Read more

• Won't start

Replaced srark module Read more

• Gas smell
• Won't start

I replaced the burner head. I turned off power to the stove, although I did not turn off the gas. I gave the old burner head a slight twist counter-clockwise until it lifted off the stove. I used the pliers to pull the wires from the old burner, then placed them onto the contacts on the new burner. Set it in place, and gave it a clockwise twist until it was snug. This stove originally came with gaskets beneath the burners, but the info for the replacement part stated that a gasket was not... Read more

These are very easy to replace ,just gave the old one a quarter turn lifted it out took the two wires off (noted where each one will go on the new burner ) pop the wires onto the new burner put it on and good to go. Read more

I ordered the brioler pan for my new stove from y'all it was a little small but that's the part number in the book that I got with the stoveyall did a great job fast shipping just what I ordered will by from again thanks Read more

Bought and installed new hinges. Repair took about an hour but I also cleaned all the glass inside and out on both oven doors. I had ordered extra screws as I read the old ones that hold the hinges were hard to get in as they were self taping but the screw labeled 5 next to the hinge were not the right ones. All old screws worked fine. You just need to put a little power to them to get them started. Easy repair. Read more

• Door won't close

It was a simple fix. I removed the six screws holding the side panel on the range. Removed the broken parks of the spring. I use a screwdriver to help stretch the new spring into place. I then replaced the side panel and screwed it on. About ten minutes work. Read more

Part arrived quickly and was an easy install1 Read more

Turned off breaker,unscrewed (2 screws) element,pulled element out from back of oven,unplugged 2 wires, attached wires to new element, pushed back in, installed retaining screws Read more

Ordered new screws and door gasket. Replaced the old door gasket now the oven warms up faster and bakes the stuff easier. Replaced the missing door trim screws. Now the door close without making noises. Read more

The clips work great and we can replace the broken ones and still have some on hand for future use. Thanks Read more

I ordered and replaced the old ignitor and the corroded mounting screws. Read more