Bath Fan Light Socket Parts

I have a Jennair jjw9630cas double wall oven, and after a few years I noticed that the light would not go out, first in the bottom oven, and then in the top oven. After doing some research I discovered this was not uncommon, and the fix usually involved replacing the hinges and/or the hinge receptacles. It didn't look like a difficult fix so I ordered four new hinges and four new receptacles, which arrived quickly. I found a video on YouTube that showed how to replace the hinges and it... Read more

• Ice maker not making ice
• Ice maker won't dispense ice
• Leaking

Much easier than expected, I was certain it had to be a water line but the solved everything Read more

Went on line to check troubleshooting sites, then went on UTube to watch a video on how to repair the appliance, then ordered the part from you, the used the video as a guide to replace the part. worst part was getting the clip off the fan blades and the putting it back on Read more

In the past, I replaced some electronic components on our gas dryer, the solenoid and the electronic ignitor, but the rest of the dryer looked more difficult to repair if needed in the future. I was wrong. I went unto AppliancePartsPros.com and watched some repair videos on dryers like mine that make big thumping sounds while drying. This happened when I googled my dryer model number in an attempt to find out is capacity, because I wanted our new dryer to have the same capacity. I found out... Read more

After extremely poor support from WhirlpooI and researching numerous U-Tube videos, I fully troubleshot potential failed components and connections. All appeared to function properly, so I reassembled the unit and experienced the same problem as before. I then narrowed down the problem to either the Touchpad ($57+$8 shipping) or the control board ($295+shipping). If those did not work, then a new Microwave of better quality, reliability and support than original microwave, Unfortunately,... Read more

Shut off power in the panel box - easier than getting at the plug behind the unit. Had to take out the lower full-width drawer and the two crispers next. Removed two screws on the shelf above the wide drawer and removed the two shelf parts. Next was removing a screw from each wide drawer support. Then I pulled the support forward about an inch to disengage it from a post towards the back. There is a wiring connection in the right-hand support you will need to disconnect. Next, I removed a... Read more

It was a classic horror story, but with a happy ending! I called a classic, "regular" repair company that I obtained on-line. My Whirlpool was 2 months out of warranty, so the repairman charged a trip-fee of $95 that would be subtracted from the cost of my repair. "Lee" showed up an hour late, even though he was told that I had to leave for work by 10:30 (-He assured me that he would have me fixed by then). The refrigerator was rolled out of its spot, and Lee began to remove the back cover... Read more

• Will not tumble
• Takes too long to dry
• Noisy

I FOUND the website on t internet, found my part ordered it and watched the how to video ,repaired the dryer myself. Awesome Website. Read more

Replaced both lights Read more

It was after 11:00 at night a few nights ago, I couldn't sleep listening to the whining of the fan in the freezer, it was running and making noise sounding like waaoooww, waaaoww. It also sounded like grumbling of a garbage disposal. The refrigerator fan motor was so noisy it was keeping me up all night going on and off running really loud and about to fail. So I was desperate, and called AppliancePartsPros when I couldn't get to sleep near midnight because the fan was so noisy and Bud in... Read more

Top mounted freezer with bottom refrigerator. Kenmore Elite Shut off the power Remove all food stuff from freezer (placed in ice chest) then shelves. Removed the ice maker, (easy!) 3 screws and unplugged wires. 2 screws in the back panel. Pulled top forward - downward Unplugged wiring harness from back wall of freezer, removed ground wire from panel Pulled fan blade off. (Fan was attached to back wall, not removable back panel) Removed 2 screws to get to fan motor. 'Unsnapped ' motor... Read more

It was an easy repair just screwed in. The ordering process and simple no hassle and got here fast! I will definitely order from you again Read more

I wanted to avoid pulling the drum. Luckily, my blower was easily accessed by pulling the front bottom panel. A couple of sheet metal screws were all I needed to remove the fan housing cover. I knew the fan was on reverse threads, i.e. righty-untighty. As it spins it tightens so no need for a retaining nut. I took off a screw holding on the exhaust tube and wiggled it out. I found the broken teeth inside. With the tube out of the way I was able to slide a crescent wrench in back and place... Read more

While waiting for parts for GE repair man to fix the fan issue the interior lights acted up, first one flickered and then went out followed by all the rest going dim. After reading stories on your web site, I ordered a couple of replacement lights and after installing the burnt out one they all came back to full strength! Thanks for the info and parts! Read more

Originally the dryer was squeaking a lot, so I purchased a new belt tensioner, but the original tensioner was an old-style no wheel tensioner, so that wasn't the source of the squeaking. I saw a lot of lint had built up inside the unit where there shouldn't have been that much. So I viewed a few videos on the Appliance Pros site and saw that the rear wheel guides were the cause of the squeaking and the rear felt drum and blower housing seal needed to be replaced. The rear blower housing was... Read more

• Noisy
• Fridge too warm
• Freezer section too warm

I changed the motherboard - computer and also changed the motor in the freezer, because it was doing a howling sound every time it turned on. The repair technician asked for $500 for a repair and that is on top of the $230 I paid him two days before. I looked up the parts and decided to try myself and it paid off. Great instructional videos. Thanks Read more