Wfk2401uc Parts

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

This replacement foot supports and levels your appliance so it sits steady and operates smoothly. Replace a worn or missing foot to restore proper height, reduce wobble, and help protect surrounding surfaces.

• Supports the base/frame to maintain proper height and alignment
• Provides leveling adjustment so the unit remains stable
• Helps reduce rocking, vibration, and rattling during operation
• Replace if the original foot is cracked, stripped, missing, or won't adjust

• Disconnect power; shut off water or gas supplies if applicable
• Carefully tilt or raise the unit to access the foot location
• Remove the damaged foot and install the new one per design
• Level the appliance front-to-back and side-to-side; verify stability before use

The Drain Pump is an OEM part for Bosch washing machines. It works to remove water from the machine after each cycle is complete, preventing moisture buildup.

Causes of drainage trouble include blockages in hoses restricting water flow or internal pump components wearing down from continuous use and impacting efficiency.

Symptoms of drainage problems are:

• Excess water remaining in tub after wash cycle
• Drain hoses failing to properly empty after spin
• Unusual sounds or vibrations from pump area
• Cycles unable to fully complete

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

Drum shock absorber for front-load washers. This damper connects the tub to the chassis and controls movement during wash and spin, reducing vibration and noise so the washer can ramp to proper spin speed without banging.

• Damps and stabilizes the drum to control vibration during acceleration, spin, and coast-down
• Helps reduce shaking, banging, and "walking" across the floor
• Can help address out-of-balance messages and noisy operation
• Worn shocks may leave loads wet after spin or cause loud thumping

• Disconnect power and shut off water before servicing; move the appliance to access panels safely
• Access the shock from the front or rear per model; support the tub to relieve tension
• Note pin/bolt orientation; transfer any reusable hardware and fully seat both ends of the new shock
• Consider replacing them as a set for balanced damping; run a short test cycle to verify stability

This heating element replaces the dishwasher tub heater to warm wash water and support drying performance. Restores proper water temperature so detergents and rinse agents work effectively during cycles. What it does:

• Heats wash and rinse water to help remove soils and dissolve detergent
• Supports the dry cycle by raising tub temperature for improved moisture removal
• Helps maintain correct cycle temperatures for sanitation and cleaning performance
• A failed element can cause no-heat conditions, poor drying, or extended cycle times

• Disconnect power to the appliance before starting any work to avoid electric shock
• Inspect and replace only the element shown in the service diagram; handle with care to avoid damage
• Verify electrical connections and test the element for continuity with a multimeter before and after installation

2 included - Front load

This holder is a replacement mounting bracket that secures a small internal component in place to restore proper alignment and support. It helps keep parts stable so the appliance operates as intended. What it does

• Secures and supports an internal component to prevent movement or misalignment
• Replaces cracked, broken, or worn mounting points that allow rattling or improper part position
• Restores stable contact where a loose component causes intermittent operation or noise
• Fits a specific OEM location; use the part number to confirm exact application

• One replacement holder/mounting bracket

• Disconnect power and water before starting any repairs
• Inspect surrounding clips or fasteners and reuse or replace as needed—this part typically snaps or screws into place
• Handle plastic mounting parts gently to avoid cracking during installation

A flat seal ring that forms a watertight gasket for pumps and valves, helping prevent leaks and maintain proper water flow in appliance wet systems. Replaces worn or damaged rings to restore reliable sealing. What it does:

• Creates a tight seal between mating metal/plastic parts to stop water leaks
• Keeps pump housings and valve connections watertight under normal operating pressure
• Helps maintain correct water flow by preventing bypass around seals
• Commonly replaced when brittle, cracked, or deformed from wear or heat exposure

• Disconnect power and shut off water supply before starting any repair
• Inspect mating surfaces for damage or debris and clean before installing new ring
• Seat the ring evenly without twisting or over-stretching to avoid leaks