Need Help?
Call
Dissolves limescale, mineral deposits, and odor-causing residues from dishwasher tub and spray system. Use monthly to maintain peak cleaning performance.
Very smooth. I ordered the door and the control panel. It is helpful to have an extra set of hands when removing the screws from the door or place something under it so it doesn’t drop. The door comes off with about 10 screws. They are different length. Short screws go into steel, long go into plastic. Remove the door and upper facia/control panel. You’ll need to disconnect the wires. The panel has two parts that need to be transferred. 1. The electronic panel. It’s white and has a row of... Read more
Replacement silverware basket for dishwashers. Holds flatware during wash cycles. Order if your basket is cracked, broken, has holes, or is missing.
Replaced racks, Read more
Replacement spring and cable assembly for dishwasher doors. Balances door opening and closing. Needed when cable breaks, spring snaps, or door drops.
The door cables attach to springs that help the user open/close the dishwasher door. I attached the new door cables to the springs then attached springs to the intended mounting locations on the door. However, the new cables were shorter than the originals. This created enough tension in the springs to cause the door to close by itself. I was forced to change the springs' mounting locations. Fortunately, I was able to attach the springs to cut-outs in the door that reduced spring tension. ... Read more
This is the complete upper rack assembly for a dishwasher, including the rack frame and roller wheels for smooth sliding in and out of the tub. It holds cups, glasses, and smaller items during the wash cycle. Replace this rack assembly if the frame is rusted, warped, or has broken tines, or if the wheels are cracked and the rack no longer slides properly.
Replaced upper rack (it comes with wheel assembly). The only tricky part was removing spray bar from old rack. Read more
This is the lower dishrack assembly that holds plates, pots, pans, and other large items during a dishwasher cycle. It includes the rack frame and rolls on wheels along the interior tracks for easy loading and unloading. Replace this rack assembly if the tines are broken, rusted, or the vinyl coating is peeling off, which can cause rust spots on dishes and damage to the dishwasher interior.
Soap dispenser door won't open or latch is broken? This detergent dispenser assembly fixes dispensing failures. DIY repair takes 10-15 minutes.
This was a pretty easy fix. Removed the screws around the perimeter of the inside cover of the door and pressed the outer door cover upward to release it from slots retaining it. There are four wires to remove (2 for the detergent door release and 2 for the rinse agent release). Removed the 6 screws retaining the dispenser assembly and inserted the new one. Reassembly is simply in reverse order. Problem solved for less than the cost of a service technician's call! Read more
This side mounting bracket kit includes the hardware needed to secure a dishwasher to the adjacent cabinetry from the sides rather than from the countertop. It is commonly used in kitchens with granite, stone, or other countertops where top-mounting screws cannot be used. Replace this kit if the original brackets are bent, broken, or missing, causing the dishwasher to shift or slide during operation.
Installed this part Read more
Dishwasher not filling with water or leaking? The water inlet valve controls water flow into the tub. Common DIY repair—moderately easy to replace.
I would open door after initial fill and noticed little or no water. I also could not hear water flowing from control valve. I replaced the water control valve and issue resolved Read more
Replacement wheel assembly for dishwasher racks. Snaps onto lower or upper rack to restore smooth gliding. Needed when wheels are broken, cracked, or missing.
Replace your dishwasher door gasket to stop leaks and restore a tight seal. Fits between the door and tub to prevent water leakage. Confirm fit by model.
The gasket is fairly straightforward: it's just a press-fit right in to the channel. What you need to know is that you need to stretch the gasket material lengthwise prior to installation; if you don't it will be too short. The problem is that the bottom seal is not included with this gasket kit. The bottom seal begins to loosen at the corners and then begins to allow water past the door. The only way the bottom seal is sold is as part of the inner door assembly, which is costly. I removed... Read more
This seal kit includes the gaskets and sealing components that fit between the dishwasher tub and the outer cabinet. These seals prevent water from leaking out of the wash compartment during operation. Replace this kit if you notice water pooling underneath or around the sides of the dishwasher during a wash cycle.
Fix a dishwasher that won't drain or leaves standing water. This drain pump assembly removes water at cycle end. Moderate DIY repair, 30-45 minutes.
Ordered a new pump and installed, took about 15 min. Reinstalled the dishwasher and tested still not draining. Disassembled and checked for pump power and found no problem. Removed drain hose from pump housing and found a blockage cleaned out blockage and hooked up the shop vac to drain hose under sink and made sure it was clean. Reassemble and reinstall with old pump, works great! Guess I now have a spare pump in stock. Read more
This spray arm assembly distributes high-pressure wash water inside the dishwasher and spins to cover the racks. Replacing a cracked or clogged arm restores proper spray coverage for cleaner dishes and consistent wash performance. What it does:
Fix a dishwasher that won't start when the door is closed. This door latch assembly engages the closure mechanism so your unit recognizes the door is secure.
Surfed the web, got advice, ordered the part, shut-off the electric power, disassembled back panel of door, removed wires for old switch and installed onto new electric door latch. Reassembled door panel - it is a little tricky, need some patience to get it all together, but it does go easily. Read more
The Mounting Bracket is an OEM part for Frigidaire dishwashers. It is a metal component that secures the dishwasher to the surrounding cabinetry. The mounting bracket provides structural support and stability during operation.
Causes of a bad mounting bracket can include damage from installation/removal, cracks or deformities from heavy loads, or broken welds/fasteners holding it in place.
Symptoms of issues with the mounting bracket include:
This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.
This pressure switch monitors the water level inside the dishwasher tub and signals the control board when the correct fill level has been reached. It uses air pressure from a small tube connected to the tub to detect water height. Replace this switch if the dishwasher overfills, does not fill with enough water, or displays fill-related error codes.
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.