Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Refrigerator making loud noises or not cooling? A worn evaporator fan blade often causes these issues. DIY-friendly repair typically takes 30 minutes.
1. After hearing a loud noise on the freezer side of unit about halfway up, I started investigating what it could be? My conclusion was evaporator motor or evaporator fan blade. One of the signs of this issue was a distinct change in sound when I opened the freezer door. I ordered a new motor and blade, not knowing exactly what it was. 2. I couldn't get water to dispense, so I changed the filter and that wasn't the problem. I ordered a water valve and crossed my fingers. These parts arrived... Read more
Seals refrigerator door to keep cold air in and prevent frost buildup. Replace if torn, warped, or leaking to restore efficiency. Confirm fit by model.
Remove old gasket clean the area and put new gasket on Read more
NOTE: Due to manufacturer changes the color of the gasket may differ from the original part color.
Forms an airtight seal to keep cold air in and moisture out. Replace when worn to restore proper temperatures and reduce frost buildup. Confirm fit by model.
Put a new one on. Read more
Reduces contaminants for clean, fresh-tasting water and ice. Replace every 6 months or when flow slows. Verify filter compatibility with your model.
Bought a new water filter. Read more
Refrigerator not cooling properly? A damaged condenser fan blade prevents airflow over the condenser coils. Quick DIY fix—simply push into place.
I originally ordered the Fan motor from a appliance dealer. I waited for 5 days for it to arrive. In the meantime I scavenge a motor from a junk refrigerator from the dump. It worked while I waited for the motor from the appliance dealer. When I picked it up 5 days later it was the "wrong" part. I was fuming mad. I went online and found you guys and ordered the correct parts in 5 minutes. It arrived in 1 day and a half, "COOL" ! The repair went quick and smooth and now the refrigerator runs... Read more
Fixes incorrect temperature readings and short cycling. This thermistor monitors fridge temps and signals the control board. Moderate DIY repair.
Walk into the kitchen on 21 Sep. Eight year old Frigidaire refrigerator appears to be short cycling, controls are nonfunctional. Unplug it for a few minutes, plug it back in, appears to return to normal function. Return to kitchen half hour 45 minutes later it's short cycling again. Panel has codes on it (S or 5 E CE, later that changes to S or 5 Y CE). Research of codes says replace main board and control board. Not sure where this main board is. 22 Sep call appliance repair. "Soonest... Read more
Ice maker not producing ice or making very little? This ice maker assembly restores automatic ice production. DIY-friendly 5-minute installation fix.
Fit perfectly Read more
The Screw is an OEM part for Frigidaire appliances. This specific screw is designed for Frigidaire models, ensuring a secure fit and proper function in the appliance assembly. Screws like this one are critical for holding components together tightly, contributing to the overall stability and durability of the appliance. Whether used in refrigerators, ovens, washers, or dryers, this screw plays a pivotal role in assembly and maintenance tasks, ensuring parts remain securely fastened during operation.
Over time, screws can become loose, stripped, or lost during repairs or adjustments, potentially compromising the appliance's integrity and performance.
Symptoms of needing replacement screws include:
This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.
The bar retainers just snapped in and the door handle can be replaced with three screws. Took about 5 minutes total. Read more
This triple-solenoid water inlet valve controls water flow to the ice maker and water dispenser in Frigidaire and Electrolux side-by-side and French door refrigerators. If the ice maker has stopped producing ice, water is leaking from the back of the refrigerator, or the dispenser has low or no water flow, a failed water inlet valve is a common cause. The valve requires at least 20 psi of water pressure to close properly - if pressure is adequate and the valve still leaks or fails to supply water, the valve itself is likely defective and should be replaced. Disconnect water supply and unplug the refrigerator before installation. Note the positions of the color-coded water lines before removing the old valve, and confirm all push-connect fittings are fully seated with retention clips in place after installing the new one.
Replaced with a new valve. Read more
Secures door handle to refrigerator door. Replace if missing, stripped, rusted, or corroded from regular use. Essential hardware for handle installation.
I ordered a replacement handle and screws. The process was very easy with the help of one of your "pros" who found all the parts needed and took my order. I didn't realize I was getting both a refrigerator door handle and a freezer door handle in one set, but now we have the freezer handle if we need it. Removing the old handle and installing the replacement was very easy. It looks great, in fact the replacement is metal, whereas the original was plastic, so it looks better than it ever did! Read more
Ice won't crush or dispenses poorly? A worn drive blade often causes ice crusher problems. This blade crushes and pushes ice through the dispenser chute.
Initially I noticed the crusher drum was cracked and broken so I replaced the drum the retaining nut on the end of the auger and the circlip and washer. it worked fine for a time and then the drum began free wheeling. upon further inspection I discovered the retain nubs on the auger had worn down allowing the blade to slip down the auger body. so I replaced the auger, drum, drive blade, and drive cam. I recommend if you gave a problem with the ice dispenser you break down and inspect the entire... Read more
Refrigerator not cooling but freezer works? Broken evaporator fan blade stops cold air circulation. Easy DIY fix in under an hour with basic tools.
Ordered the fan blade grommet and fan motor. Read more
Specs: 10-16 X 0.500
No problem, 1 min to fix Read more
Refrigerator won't cool properly or runs constantly? The thermistor monitors temperature and signals the control board. Moderate DIY repair.
Side-mounted bracket that supports and guides freezer baskets in refrigerator freezer compartments. Replace when cracked, broken, or missing to restore basket support.
Order the parts...!!! Read more
Mounts to the freezer wall to support wire baskets. Replace if cracked, broken, or pulling away from the wall causing baskets to sag or fall out.
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.