Gldt696dooss Parts

The Lower Dishrack Stud and Roller Assembly is an OEM part for GE dishwashers. It is essential for the smooth operation of the dishwasher's lower dishrack, allowing it to slide in and out. This assembly includes the roller that attaches to the dishrack and the studs that secure these rollers in place.

Symptoms of a bad Lower Dishrack Stud and Roller Assembly include:

• The dishrack sticking or jamming when moved
• Rollers falling off or breaking
• Unusual noises when the dishrack is pulled in or out
• Difficulty in keeping the dishrack aligned within the dishwasher

Common causes for issues with the assembly often involve regular wear and tear, accumulation of detergent residues or food particles that can corrode or clog the rollers, and accidental damage from handling. If the rollers or studs are damaged, replacing them can greatly improve the functionality and longevity of your dishwasher.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Rinse Aid Cap is an OEM part for GE dishwashers. It securely seals the rinse aid dispenser, ensuring that the rinse aid is properly stored and dispensed during the wash cycle. This helps improve the drying process and prevents water spots on dishes and glassware.

You should replace this rinse aid cap if it becomes cracked, loose, or fails to seal properly. Common causes of a bad cap include wear and tear from regular use, damage from over-tightening, or deterioration due to exposure to dishwasher detergents and rinse aids.

Symptoms of a bad rinse aid cap include:

• Rinse aid leaking or spilling inside the dishwasher
• Cap not staying securely in place
• Poor drying performance or water spots on dishes
• Difficulty in opening or closing the cap

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This replacement dishwasher detergent dispenser stores detergent and releases it at the correct time in the cycle, while also controlling rinse-aid dosing. It restores reliable cleaning performance when the original dispenser is damaged, leaking, or won't open.

• Holds detergent securely and opens on command during the wash cycle
• Meters rinse aid during the final rinse to help reduce spots and film
• Seals to the inner door at the dispenser opening to help prevent leaks
• Typical symptoms: detergent left in cup, dispenser door won't latch/pop open, rinse aid not dispensing or leaking, visible cracks or warping

• Disconnect electrical power and turn off water supply before servicing
• Open the door and remove inner-door panel screws to access the dispenser
• Unplug the wire connector(s), release retaining screws/tabs, and remove the old dispenser
• Clean the door cutout, seat the new gasket evenly, secure the dispenser evenly, reconnect wiring, and run a leak check

The Water Valve is an OEM replacement part for GE dishwashers. Located inside the valve body, this electronically-controlled component precisely regulates water inlet and flow during each cycle of the wash sequence. The water valve utilizes sensors and timer modules to open and close water lines at the correct times based on cycle selections.

Symptoms of a defective water valve include:

• Failure to fill or improper filling  
• Inability to switch between cycles
• Water leaks from the valve body area
• Erratic or inconsistent water usage amounts

Causes of malfunction often stem from worn internal seals, mineral buildup obstructing valve ports over time, or issues with the electronic control board. Replace yours today with this genuine GE water valve for reliable water control, sensor functions, and trouble-free dishwasher cycles. 

This GE replacement part is compatible with Hotpoint, RCA, and Kenmore models.

Cylindrical filter that helps trap sediment and debris to protect your appliance's internal components and maintain water flow. Replacing a worn filter restores filtration and helps prevent clogging-related performance issues. What it does:

• Captures sediment and particulates to reduce debris reaching valves, pumps, and dispensers.
• Helps maintain consistent water flow by preventing buildup in flow paths.
• Reduces risk of clogs that can cause noisy operation or degraded performance.
• Common symptom: reduced water flow or visible particles in water/dispensed liquids.

• Turn off power to the appliance and shut off the water supply before starting.
• Relieve pressure and drain water from the lines where applicable to avoid spills.
• Inspect and replace any worn O-rings or seals; ensure the filter seats properly.
• After installation, restore power/water and run a short cycle or check for leaks.

This dishwasher microswitch is the snap-action switch used in the door-latch interlock. It signals the control when the latch is engaged so cycles start and continue only when the door is securely closed.

• Senses latch position and sends an open/closed signal to the control
• Failure signs include the cycle not starting, stopping when the door is bumped, or needing to press on the door/handle to run
• Restores reliable door-closed detection and safe operation
• Direct replacement for a worn, sticking, or inconsistent switch

• Disconnect power to the dishwasher before servicing
• Note wire positions (COM/NO/NC); transfer any actuator/lever or bracket from the original switch
• Ensure a positive "click" and correct continuity before reassembly
• Latch and strike alignment after installation

This sump gasket seals the dishwasher's sump to the tub to keep wash water contained. Replacing a worn or flattened gasket helps stop leaks and maintain proper wash and circulation performance.

• Creates a watertight seal between the sump/pump assembly and the tub bottom
• Helps prevent leaks onto the floor or into the base pan
• Maintains wash pressure and circulation by preventing air intrusion
• Replace if torn, cracked, deformed, or if water is leaking from the center/bottom of the unit

• Disconnect power and water before servicing; use gloves to protect from sharp edges
• Access the sump from inside the tub or underside (model dependent); remove spray arm/filter as needed and release the retaining ring or tabs
• Clean mating surfaces; install the new gasket evenly without twists and ensure proper orientation
• Reassemble and run a brief fill/wash to check for leaks before fully reinstalling

This pump hose and clamps create a sealed connection between the dishwasher's pump and internal plumbing. Replace when the hose is cracked or clamps are corroded/loose to stop leaks and restore a secure, watertight fit. What it does:

• Creates a sealed connection between the pump and internal plumbing
• Helps contain water flow during wash and drain operation
• Replace if the hose is cracked, brittle, swollen, or deformed
• Symptoms include water leaking under the dishwasher or loose/corroded clamps

• Disconnect power and water; pull the dishwasher forward as needed for access
• Expect residual water—protect flooring and have a towel or pan ready
• Remove old clamps and hose; fully seat the new hose on fittings, then position and secure clamps at the bead/ridge
• Run a brief cycle and check for leaks before reinstalling

Upper dishrack stop.

NOTE: The clamps no longer come with the connector hose. The part number for the clamp is WD01X10322.

The RING NUT W/GASKET is an OEM component specifically designed for GE dishwashers. This part utilizes both a ring nut and gasket to form a watertight seal around the fittings to which it attaches. 

Causes of a bad ring nut can include cracks, chips or damage to the gasket preventing a proper seal. Over time, gaskets can become brittle or deteriorate due to exposure to heat and chemicals from the wash cycle.

Symptoms of a bad Ring Nut W/Gasket include: 

• Leaks or water damage around fittings
• Puddles or standing water below connections
• Moisture or corrosion around connections
• Reduced washing or drying performance 

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models. 

If looking for the two wheel guide rail bracket order WD12X10221

This left switch breakwater is a small plastic retainer that holds the console switch assembly in place, keeping switches secure and aligned for reliable control operation. It helps restore proper switch positioning after damage or wear. What it does:

• Secures the left console switch assembly so buttons and selectors operate correctly
• Keeps the switch contacts aligned to prevent intermittent or non-responsive controls
• Helps block debris from interfering with the switch mechanism
• Commonly replaced when the switch feels loose, sticks, or the control behaves inconsistently

• One left switch breakwater

• Disconnect power to the appliance before beginning any repair
• Access typically requires removing the control console or panel; follow your model's service instructions
• Handle plastic retainers carefully to avoid cracking; replace if damaged

This sump clamping nut secures the washer/dishwasher sump seal and housing, helping keep the sump assembly sealed and stable during operation. It's a small but essential fastener for preventing leaks and maintaining proper drainage. What it does:

• Holds the sump/tub seal and sump housing tightly in place to maintain a watertight connection
• Prevents the sump assembly from loosening during spin or wash cycles
• Helps reduce leaks and related water damage when installed correctly
• Works with the factory sump and seal components as the retaining nut

• Replace only with the matching part number; verify orientation before tightening
• Hand-start threads to avoid cross-threading, then tighten to factory spec (do not overtighten)
• Disconnect power and water to the appliance before servicing