Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Oven won't light or ignites with a loud pop? A faulty igniter is usually the cause. Simple DIY fix—disconnect two screws and wire nuts to replace.
My Tappan Range, which I paid a grand total of $65.00 for, and have been using since Katrina, (Katrina in 2005 is how we measure time in South Mississippi.) I live in an old house, and I am old, too. Last winter was the coldest I can remember, and my husband (older than I and far more hard-headed) used the oven like a heater. I read all user's manuals, because I use only used stuff, I can download the manuals or read them online, and it clearly stated in there NOT to use the oven as a... Read more
The Flame Sensor is an OEM replacement part for Whirlpool gas dryers. This component plays a critical safety role by monitoring the presence of the gas burner flame during the drying cycle.
Causes of needing to replace the flame sensor can include normal wear and tear over extended use, exposure to high temperatures or corrosion, or physical damage to the sensor itself.
Symptoms that may indicate a faulty flame sensor include:
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore gas dryer models.
I used Fixya as an initial source describing my problem. I got two responses which were very helpful. One that the "coils" were probably the problem. Two, that the problem could be the thermostat or a thermistor in the dryer. I verified that AC was coming from the timing control, that both the two terminal and three terminal coils,the igniter and shut off thermostat all had continuity. I then applied AC directly to the coils: the two terminal coil ""clanked" and I interpreted that as the coil... Read more
Oven won't heat to correct temperature or won't turn off? The thermostat regulates oven heat. DIY repair typically takes 15-60 minutes with basic tools.
Removed old thermostat and pulled old thermocouple fron oven. ran new thermocouple to oven and put in clip, tistalled new thermostat using 2 phillips head screws, done. Read more
Oven won't light even with glowing igniter? Safety valve controls gas flow to burner. Moderately easy repair with gas line disconnect required.
My tenant thought that the oven safety valve was bad, but after some research, I found that the transfer of heat from the igniter had to be sufficient enough to cause the valve to open.Your agent confirmed this and reassured me that even if the igniter was glowing, there was a 99% chance that it wasn't getting hot enough. I ordered the igniter, and also the safety valve just in case, as we were going to be fixing this on Christmas eve, so the oven could be used for Christmas dinner. Your agent... Read more
Replace your cracked, warped, or hard-to-clean oven rack. This durable rack installs inside your range oven to support cookware during baking and roasting.
Sled the new ones in. No problem. Read more
Replacement top burner for gas ranges. Installs on the cooktop surface to provide flame for cooking. Order if your burner is rusted, eroded, or broken.
We took the old ones off and put the new ones on..it was easy to do ..I want to say that the girl (I think her name was Heidi) she was a big help ,she made sure that I had the right parts,I ask her to show me the picture to make sure that they look like the part ..She was a really big help. I did a survey when I ordered the parts to..Thank you for your help and the parts Anna P Read more
Replace your cracked, rusted, or clogged gas range surface burner. Mounts on the cooktop to direct gas flow for a steady flame. Easy one-screw install.
Fits some Tappan, Frigidaire, GE, and Hotpoint models. Color: Black. Diameter: 6 1/2 inches. One round gas grate per package. For the matching drip pan order 5303131115.
Tappen Gas Stove circa 1981 (uses Fridgidaire parts). Unplugged stove from 110 wall outlet. Spark control module located on back side of stove about mid-way down on left side under a black cover that juts out. Black cover had 2 phillips head screws...removed the black cover and the spark module was right there...held on by 2 additional phillips screws. Sprark module purchased was identical to old one on the stove. Removed each wire, one at a time from the old spark module (slide off) and placed... Read more
Replacement oven door seal creates a heat-tight barrier to maintain temperature and reduce heat loss. Replace if heat escapes or cooking times increase.
Looked up the part I needed...ordered and within a week, had a new door seal installed in minutes. Just snapped it in...ready to go. Read more
Secures panels and components in your range or oven. Replace if broken, bent, or missing to prevent shifting and reduce vibration noise. Confirm fit.
Removed the broken clip and installed the new one. Clipped the thermo bulb on. That was it. Easy fix. Read more
This is a genuine replacement bolt that is designed specifically for use on select lawn tractors. This tractor bolt is a specialty piece of hardware designed for use on the steering segment gear. This screw holds the gear in place and is exposed to constant vibrations and repetitive motion as a result. Over time, that can result in damage, wear, or even total breakage of the bolt and require a replacement. If the bolt isn't functional or is missing, the steering segment gear will not be secured and that can lead to further damage if left unattended. Using a genuine replacement part like this will guarantee an exact fit for compatible models. This genuine OEM gear bolt is manufactured by MTD. It is compatible with lawn and garden equipment from RYOBI, HUSKEE, Troy-Bilt, Bolens, Yard Machines, Yard Man, and Cub Cadet, along with select models from MTD. The bolt works for more than 100 compatible models. It is made of durable metal and sold as an individual unit. A wrench or socket will be required to replace this part. Always wear gloves when performing repairs on lawn and garden equipment and allow the engine to cool before doing any work.
New steering column. Read more
Black end cap that covers and secures the outer end of your range handle. Replace this part when cracked, chipped, missing, or worn for a finished look.
Ordered a new handle and end caps. Had to re-tap the threads to take the original screws. Read more
Replacement mounting screw that secures panels, trim, and components in ranges and ovens. Needed when original screws are lost, stripped, or damaged.
Body-side spacer for gas range door or lid hardware. Installs on cabinet side to set correct stand-off and alignment. Replace if cracked or missing.
Specs: 8 - 18 x 0.500
This lock washer is used frequently for a number of applications on power yard equipment. The size, 5/16, is the default for many small engine housing and manifold applications. Lock washers are used with machined bolts to fasten engine blocks to the housing of the equipment being used. The compressed washer is able to handle the constant vibration of the small gasoline engine without losing the seal between the screw or bolt and the housing. Typically these lock washers only need to be replaced when they are misplaced during repairs or when the screws that attach them have to be chiseled or cut away, meaning the washers are destroyed as well. These OEM certified replacement washers have been manufactured to the same specifications as the originals they are replacing. In addition to lawn mowers, lock washers of this type and size are frequently used on blowers, lawn tractors, cultivators, snowblowers, and trimmers. Brands compatible with this type of washer are Murray, Husky, Poulan, Bolens, Yard-Man, Cub Cadet, Troy-Bilt, Yard Machines, MTD, and Ryobi.