Kcms185jss-3 Parts

15 Amp, 125/250 Volt. Package of 2. Switches have 3/16 inch terminals.

This is a Whirlpool microwave magnetron. The microwave magnetron is one of the main components that control the heating function in the appliance. If a microwave has suddenly stopped heating but is still turning on normally, the problem could be the magnetron. Use a voltage tester to confirm whether this part is causing the problem. This component is made for installation in a microwave and oven combo where the microwave doubles as a vent hood. To replace this part, begin by unplugging the appliance and removing it from above the oven. Two people will be needed for this repair. This part requires exposure to highly sensitive electrical parts that could cause severe injury.This is a genuine OEM replacement part sourced directly from the manufacturer. This part is compatible with Whirlpool, Magic Chef, Amana, and Maytag appliances.

This electrical safety fuse opens the circuit when a short or overcurrent occurs. Replacing a blown fuse can help restore power after the root cause is corrected, protecting controls and wiring from further damage.

• Protects the appliance by interrupting power during overcurrent or short-circuit events
• When open/blown, the appliance may be completely unresponsive
• Helps prevent damage to control boards and wiring during faults
• Often fails after a component shorts or a power surge occurs

• Disconnect power to the appliance before servicing
• Use a multimeter to test the fuse for continuity; replace only if open
• Install a fuse with the exact same rating and form factor as the original
• If the new fuse blows again, stop and diagnose the underlying fault; consider service for high-voltage systems

The Screw is an OEM part for Whirlpool microwaves. It is responsible for securing various parts of the microwave together. This screw ensures a tight and secure fit for parts and helps maintain the structural integrity of the microwave, preventing any loose or rattling parts.

A bad microwave screw can occur due to wear and tear, accidental damage, or misplacement during maintenance or repairs. If you notice symptoms such as loose or wobbly components, difficulty in opening or closing the microwave door, or abnormal noises while the microwave is in use, it may be time to replace this part.

Symptoms of a bad microwave screw include:

• Loose or wobbly components
• Difficulty in opening or closing the microwave door
• Abnormal noises during operation

Restore your Whirlpool microwave by replacing the faulty or missing microwave screw with this genuine OEM part.

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
 

This stirrer cover rivet secures the microwave's stirrer cover in the ceiling of the oven cavity. A snug, intact cover helps protect the stirrer mechanism from splatters and keeps it properly positioned for consistent heating.

• Holds the stirrer cover firmly in place inside the cavity
• Helps prevent rattling noises from a loose or missing cover
• Can address issues like a sagging or fallen stirrer cover
• Replacing damaged or missing rivets supports even cooking performance

• Disconnect power to the microwave before servicing
• Access the interior cavity; support the cover while installing the rivet
• Insert through the cover and mounting hole; seat fully so the cover is secure
• Microwaves contain high-voltage components.

This mounting bracket secures the door lock/latch assembly to the washer's front panel, keeping the latch properly aligned so the door locks and unlocks reliably during cycles. Replacing a damaged bracket helps restore safe, consistent door operation.

• Holds the door latch assembly firmly in place
• Helps prevent door lock errors and incomplete cycles caused by misalignment
• Common symptoms include door not locking, cycle not starting, or "Door Locked" error codes
• Maintains correct latch position to reduce vibration-related issues

• Unplug the appliance before servicing
• Access is typically from the front; remove the door gasket clamp to reach the latch area
• Support the latch assembly while swapping the bracket to avoid straining wiring
• Test door operation and run a short cycle check after reassembly

High-voltage capacitor for microwave ovens that stores and releases the electrical charge needed to drive the magnetron, restoring heating when the original capacitor has failed and preventing further electrical stress. What it does:

• Stores high-voltage electrical energy used by the magnetron to produce microwave energy.
• Works with the high-voltage transformer and diode; a failed capacitor can cause no-heat or reduced-heat conditions.
• Common, widely accepted symptoms: microwave not heating, loud humming, arcing/sparking, or blown fuse.
• Replacing a defective capacitor can stop repetitive electrical faults and protect other high-voltage components.

• Always unplug the appliance before beginning service and discharge the capacitor with an appropriate resistor or discharge tool.
• Handle and test the component using insulated tools; capacitors can retain dangerous charge even when unplugged.
• Verify correct part orientation and secure connections; use only the exact replacement specified by the manufacturer.

This is a genuine replacement mounting screw used to secure appliance panels and components. It restores proper fastening to reduce vibration and prevent parts from loosening during normal operation. What it does:

• Secures panels, brackets, or trim to the appliance frame
• Prevents rattling or vibration caused by loose fasteners
• Keeps wiring and small components held in place
• Helps maintain proper alignment of removable parts

• Disconnect power to the appliance before servicing
• Use the correct screwdriver or bit to avoid stripping the head
• Start threads by hand, then tighten until snug; do not overtighten
• Keep removed fasteners organized to ensure correct reassembly

Size: 4 x 8mm.

A left-side base plate that restores proper support and alignment for the appliance cabinet, helping stop rattles and ensuring correct panel fit. Designed to replace a damaged or bent left base plate quickly and reliably. What it does:

• Provides structural support for the appliance's left lower cabinet area to maintain correct panel alignment
• Replaces bent, cracked, or corroded base plate sections that cause gaps, rubbing, or vibration
• Helps restore secure mounting points for adjacent panels and components
• Reduces rattling and movement that can occur from a damaged base plate

• Basic mechanical skills and common hand tools required
• Disconnect power and water before beginning work
• Handle edges carefully; fasten with manufacturer-specified screws and torque where provided
• If mounting holes or adjacent brackets are damaged, inspect and replace as needed before installing

This right-side base plate replaces a worn or damaged support panel to restore proper alignment and stability to the appliance's lower assembly. Durable stamped metal designed to fit factory mounting locations. What it does:

• Supports and secures the appliance's lower cabinet or base assembly to prevent gaps and misalignment
• Restores correct panel alignment that can cause rubbing, rattling, or uneven operation
• Provides a stable mounting surface for adjacent trims and components
• Helps maintain cabinet rigidity after impact or corrosion-related wear

• Disconnect power to the appliance before starting any repair
• Basic hand tools (screwdrivers, nut drivers) are typically needed to remove the lower access panel and fasten the replacement plate
• Retain existing mounting hardware when possible; replace with manufacturer-specified screws if corroded
• Follow the manufacturer's service manual for disassembly and reassembly steps to avoid damage