Ksb1575ccuo Parts

The KitchenAid Blender Drive Coupler is an OEM part for KitchenAid blenders. This part connects the blender's motor to the blade assembly.

Causes for issues with the drive coupler often involve overloading the blender, blending hard or frozen ingredients without sufficient liquid, or simply the natural degradation of the component over time.

Symptoms of a malfunctioning Blender Drive Coupler include:

• The blender's motor running, but the blades not spinning
• Visible wear or damage to the coupler's teeth
• Unusual noises during operation, indicating a misalignment or damage

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This 60-oz blender jar assembly replaces a damaged or worn jar so you can safely blend full batches again. It provides a secure container for ingredients and a proper fit on the base for consistent, mess-reducing performance. What it does:

• Provides a 60-ounce container for blending, mixing, and pouring
• Interfaces with the blender base for efficient circulation of ingredients
• Helps prevent leaks when the jar and sealing surfaces are intact
• Typical symptoms of a bad jar: cracks, leaks, clouding, or an unstable fit on the base

• One 60-oz blender jar assembly

• Unplug the blender before servicing
• Remove the old jar; if your model uses a separate blade/collar, ensure gaskets are properly seated during reassembly
• Wash the new jar before first use and confirm it seats flat on the base
• Fill with water and test for leaks before blending food

The Lock Jar is an OEM replacement part for Whirlpool Blenders. Securing the blending jar safely during operation, the lock enables smoothie and food preparation.

Causes of a faulty blender locking jar include normal wear of locking tabs and ridges that hold the jar in place through years of use. Exposure to liquid residue over time may potentially compromise lock performance.

Symptoms of a bad locking jar include:

• Potential tipping or detachment of jar during blending posing spill and injury risks
• Inability to achieve proper suction seal jeopardizing blend consistency
• Lock failure releasing sharp blade assembly with attached jar interior

This is a genuine Whirlpool OEM replacement this part is also compatible with Maytag, Jenn-Air and some Kenmore models.

This replacement coupling links and seals wash-system components so pressurized water reaches the spray arms. Replacing a cracked or worn coupling restores cleaning performance and helps prevent drips at the connection point.

• Provides a secure, watertight connection within the dishwasher wash system
• Helps deliver proper water flow to the spray arms
• Failure symptoms can include poor cleaning, spray arms not turning, a loose/detached feed tube, or leaks at the connection
• Replace if the coupling is cracked, deformed, or stripped

• Disconnect power and shut off water before servicing
• Remove dish racks and access the coupling at the manifold/feed-tube area per your model
• Inspect existing seals/O-rings and replace if worn
• Seat and lock the coupling fully; run a short cycle to check for leaks

This washer lid assembly replaces a cracked, broken, or misaligned lid so the washer can close and lock correctly, restoring safe operation and reducing cycle interruptions caused by a lid that won't align or latch.

• Covers the tub opening and aligns with the lid lock/strike for proper engagement
• Restores the safety interlock so wash cycles can start and run without interruption
• Helps contain splashing and keeps debris out of the washer when not in use
• Typical symptoms include visible cracks or shattering, warped or loose lid, broken hinge area, or intermittent lid-lock errors

• Disconnect power before servicing
• Protect the cabinet surface and support the lid during removal/installation to prevent damage
• If required by your model, transfer existing hinge hardware and fasteners to the new lid
• After installation, check alignment and ensure the lid lock engages smoothly before running a cycle

This replacement seal keeps liquids and food particles out of the blender motor housing to protect internal components and help prevent leaks. Fits the motor assembly where the shaft passes through the housing. What it does

• Seals the motor shaft opening to help prevent liquid from entering the motor housing.
• Reduces risk of motor damage or shorting caused by leaks into the base.
• Helps stop leaking at the blender base or around the blade assembly when worn.
• Replace if the seal is cracked, flattened, swollen, or shows visible wear.

• Always unplug the appliance before disassembly and removal of the jar or motor housing.
• Remove the blade and jar assembly per the service diagram to access the shaft seal; inspect mating surfaces and replace damaged components.
• Ensure the new seal is seated evenly around the shaft and in its groove; do not force or over-stretch the seal.
• After reassembly, run a short water test (with the unit unplugged from any direct water source) to check for leaks before normal use.

A replacement shim that restores correct spacing and alignment between appliance components to reduce vibration and rubbing. Helps ensure parts fit together properly after repair or during reassembly. What it does:

• Provides precise spacing and alignment between panels, brackets, or assemblies
• Helps reduce noise and vibration caused by parts rubbing or sitting out of alignment
• Used when reseating or replacing components to maintain proper clearances
• Small, simple part that supports reliable operation of surrounding hardware

• Disconnect power to the appliance before starting any repair
• Install in the same location and orientation as the original shim; retain any removed fasteners
• Use basic hand tools; avoid forcing parts—check alignment as you tighten
• Refer to the manufacturer's service manual or parts diagram for exact placement and torque guidance

This replacement appliance foot restores stable, level support for your appliance so it sits flush and reduces rocking or vibration. Use it to replace a worn or damaged leveling foot that prevents proper balance. What it does:

• Provides adjustable support so the appliance can be leveled on uneven floors
• Reduces rocking, excessive vibration, and movement during operation
• Helps correct uneven door/Drawer alignment caused by a collapsed or missing foot
• Restores proper weight distribution for safer operation

• Disconnect power and water before working on the appliance
• Tilt or raise the appliance per the manufacturer's guidance; use blocks or an appliance jack for safety
• Thread the foot into the mounting insert and adjust height until the appliance is level; hand-tighten and verify stability
• Do not exceed recommended force when tightening; inspect for secure fit and proper clearance

This lid assembly replaces a damaged or broken top lid on compatible top-load washers, restoring a secure cover and proper operation. It helps protect the wash tub and enables the lid to open and close smoothly. What it does:

• Provides a durable replacement for cracked, warped, or broken washer lids
• Restores proper lid alignment and helps the lid stay closed during operation
• Addresses issues where a damaged lid prevents normal washer use or causes noise
• Replaces worn hinge or latch mounting areas that can cause uneven closing

• Disconnect power to the washer before beginning any repair.
• Handle edges carefully to avoid damage or injury; wear gloves and protective eyewear.
• Basic hand tools are typically required to remove hinge screws and transfer any latch or trim pieces.
• Verify lid alignment and secure all fasteners; if the washer still fails to operate, check the lid switch assembly.

This painted housing replaces the oven backguard panel to restore the exterior finish and support surrounding controls. It gives a clean, factory appearance where the original housing is dented, scratched, or corroded. What it does:

• Provides the finished exterior backguard for the upper rear area of the range/oven
• Restores mounting and alignment for controls and trim pieces
• Helps protect internal components from incidental contact and debris
• Improves appliance appearance when the original housing is damaged or cosmetically worn

• Designed to install with factory fasteners; keep track of screws and brackets during removal
• Disconnect power to the appliance before beginning service to avoid electrical shock
• Use basic hand tools; avoid overtightening fasteners to prevent paint damage
• If retaining trim or control assemblies, support them during housing removal to prevent damage