Your search "holder amana red" did not match any products.
Showing results using some of your search terms
By: Whirlpool
Mfg Number: WP3392519
Stop dryer downtime in its tracks — install the Whirlpool WP3392519 OEM Thermal Fuse in minutes.
OEM Quality Fast 1–2 Day Shipping* Free Tech Help
Why choose this fuse?
- Guaranteed OEM: built by Whirlpool to Whirlpool specs — no risky aftermarket clones.
- Broad compatibility: works with Whirlpool, Kenmore, Maytag, KitchenAid, Roper & more.
- Quick delivery: over 94 % of APP orders arrive in 2 days or less.
Fixes these common dryer problems
| Problem |
How the fuse is involved |
| Dryer won’t start |
Blown fuse interrupts motor circuit |
| No heat / not enough heat |
Heater circuit disabled for safety |
| Cycle ends early |
Over-temp trip stops cycle |
| Control panel dead |
Power to controls interrupted |
4-step DIY installation (≈10 min)
- Unplug dryer and remove rear panel.
- Locate thermal fuse on blower housing.
- Transfer wires; secure new fuse with ¼-inch nut-driver.
- Clean the vent & lint path before testing to prevent repeat failure.
*Video tutorial below.
Ready to get heat back?
Click Add to Cart now & enjoy industry-leading 1–2 day delivery on
More
$17.95
- Compare At:
- $21.54
- You Save:
- $3.59
By: Whirlpool
Mfg Number: 341241
Get your dryer spinning smoothly again - install the Whirlpool 341241 OEM Drum Belt in minutes.
Why this belt?
- Exact factory spec: 92 ¼-inch length × ¼-inch width, 4 ribs / 3 grooves - built to Whirlpool standards, not a generic copy.
- Broad compatibility: Fits most Whirlpool-made dryers - Kenmore 110-series, Roper, Estate, Maytag, KitchenAid, Admiral, Crosley, Amana & more.
- Quiet, durable rubber: Reinforced EPDM resists cracking and stretch for years of reliable tumbling.
Fixes these common dryer problems
| Problem |
How the belt solves it |
| Drum won’t turn |
Transfers motor rotation to drum |
| Loud squealing / thumping |
Replaces stretched or frayed belt |
| Burning-rubber smell |
New belt stops slippage & heat build-up |
| Damp clothes / long cycles |
Restores correct drum speed & airflow |
DIY install — about 15 minutes
- Unplug dryer; remove lint screen housing & front panel.
- Release belt tension at idler pulley; lift drum slightly to slide old belt off.
- Loop new belt around drum, idler pulley and motor pulley (ribbed side down).
- Re-assemble, run test cycle - enjoy quiet, consistent tumbling.
More
$14.64
- Compare At:
- $17.42
- You Save:
- $2.78
By: Whirlpool
Mfg Number: 279838
Restore full heat and end long dry cycles - install the Whirlpool OEM Dryer Heating Element.
Why this heating element?
- Factory-spec 5400 W / 240 V heating element with nickel-chromium coil - built by Whirlpool to Whirlpool OEM standards.
- Broad compatibility: fits Whirlpool, Kenmore 110-series, Roper, Estate, Amana, Maytag & more 27-inch dryers.
- Built to last: high-temp terminals & mica insulation resist fatigue and hotspots.
Fixes these common dryer problems
| Problem |
How the element solves it |
| No heat / cold drum |
Replaces burned-out coil to restore heating circuit |
| Takes forever to dry |
Full wattage brings drum back to target temperature |
| Stops mid-cycle |
Prevents over-cycling caused by faulty element |
| Burning smell |
New coil eliminates hot-spot arcing & insulation burn |
DIY install — about 20 minutes
- Unplug dryer and remove back panel to access heater housing.
- Disconnect wires; remove housing screws and slide assembly out.
- Swap old element for new, re-use hi-limit thermostat if still good.
- Re-assemble, run test cycle - enjoy fast, even drying.
More
$53.95
- Compare At:
- $64.74
- You Save:
- $10.79