Ev160nztq Parts

I have a Jennair jjw9630cas double wall oven, and after a few years I noticed that the light would not go out, first in the bottom oven, and then in the top oven. After doing some research I discovered this was not uncommon, and the fix usually involved replacing the hinges and/or the hinge receptacles. It didn't look like a difficult fix so I ordered four new hinges and four new receptacles, which arrived quickly. I found a video on YouTube that showed how to replace the hinges and it... Read more

Replaced door switch - it took less than 5 minutes - works perfectly Read more

• Noisy
• Fridge too warm

The fridge is 20+ years old in a home we recently moved into. It sounded like a motor getting stuck on something or grinding weird... was hoping it wasn't something more serious. Found this site, clicked 'noisy' and got the replacement evaporator fan motor blade as well as the motor evaporator. Turned out I didn't really need to replace the fan blade, but since I had it and ours was old, figured I might as well put in the new parts. Followed the videos here, which were really helpful. The... Read more

Touch up paint Read more

Replaced It With New One Read more

• Noisy

Emptied the contents of the freezer into coolers. Removed the rack shelves. Listened when the unit was running to see if I could hear where the noise was coming from. UNPLUGGED the freezer!! The noise seemed to be coming from the back inside so I took out 4 Phillips screws in the back that was easily accessed. Removed the panel and took a look inside, this panel reveled cooling coils, a fan and interconnection tubes and wires. I found that the fan blades had moved back on the shaft to the motor... Read more

Replacing the cold control solved the problem. While i was at it i also replaced the defrost timer and installed a new ice door. Read more

• Light not working

I saw your video on you tube and it seems very easy to do it my self, so I ordered the parts and I did it my self. It was very easy. Thank you for sharing with us on how to did it. One more thing, the parts arrived on the time they said it would come. Read more

The fan blade had vibrated down the shaft of motor and was hitting the fan supports. I replaced motor and new fan blade. The motor was still operating but since I had everything opened up I changed out the motor anyway. Freezer working fine now. The only unforeseen problem is there was a black wire that had to be transferred to the three prong wiring harness. Read more

Replaced the defrost timer. It was not located where the parts explode suggested in the thermostat control box which is located in the upper right corner of the liner. It was in fact outside the freezer compartment on the back lower left support (when looking at the back of the freezer). It is secured with 2 sheet metal screws with a 1/4 hex head. The manual override dial is visible through a punched hole in that support. Just remove the 2 screws, disconnect the electrical connector. Then... Read more

Rebalanced the freezer and put in a new door gasket. Read more

Removed the handle with two screws on the inside front and pulled out the custom wood panel. Pulled the compactor out from under cabinet. Tipped it over on back of unit, supporting it with a little foot stool. Unscrewed two lower screws at bottom of unit holding black trim panel (that held wood panel in place) and lower black rubber flap. Removed two screws on lower outside side of unit that held the foot pedal. Slid off black U shaped metal frame from top of compactor towards bottom. Slid on... Read more

Unplugged freezer, left door open to defrost, after one day was able to remove back panel, coils still iced up. Left door open another 24hrs to allow the coils and wiring to clear of ice. Then located the defrost thermostat, unplugged and removed. Placed the defrost thermostat in a different working freezer overnight, checked with a continuity testor, getting intermittent good readings, replaced with a new defrost thermostat. Plugged in the freezer marked the defrost timer position, checked for... Read more

Looked up model on your website. You had all the parts I needed, numbered and visually shown. Perfect! Read more

The grill vent is only held in place by two screws. Super simple fix. Remove the two screws and the old grill vent, position the new vent and put the two screws back in. Replacing the cord required that cabinet to be removed. Lots of screws on the back, top and bottom. Once the screws were removed, the cabinet pulled back. The power cord connections were then clearly visible. Undid the two wire connectors and unscrewed the ground wire from the body to remove the old power cable. Installed the... Read more

Replaced heat defrost element and this was a rare find. Read more