Need Help?
Call or text
The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells. This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.
I followed Matt's awesome video from AppliancePartsPros.com to build up my "I can do this" reserves. But here's the story leading up to that point... We purchased our Samsung WF419 on a “Black Friday” special November 2009 expecting to get some good years out of the washer/dryer pair. We don’t run more than 2 or 3 loads a week in the washer, so ours has had relatively little use over the beginning of its anticipated and expected long life-cycle. When the “thumping” started on the spin cycle a... Read more
The Drive Belt is an OEM part for GE washing machines. It functions as a critical component that connects the motor to the drum, transferring power from the motor, which in turn allows the drum to spin during the wash cycle. Made from rubber reinforced with fibers, this belt is designed to withstand the stress of spinning and agitating motions.
Symptoms of a bad Drive Belt include:
Causes of drive belt failure typically include regular wear and tear from use, overloading of the washer which puts extra strain on the belt, or exposure to oils and other substances that can degrade the rubber.
This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
Ordered new transmission, nut, split washer and spanner wrench to do the install. very straight forward fix after watching the video. spanner wrench is a must or the correct large socket with an impact driver. it was corroded on pretty well let the liquid wrench work for a while and then beat it off. approximately 2 hours to do to fix, spent some time cleaning stuff up also though. washer was 12 years old and debated scrapping it and getting a new one but then it would not match the dryer. ... Read more
The Timer Knob Clip is an OEM part for GE washing machines. It secures the timer knob to the timer shaft, allowing users to set and adjust the washing cycle duration accurately.
You should replace the timer knob clip if it becomes worn out, broken, or lost. Common causes of a bad timer knob clip include regular use leading to wear and tear, physical damage from excessive force, or accidental breakage during maintenance or operation.
Symptoms of a bad timer knob clip include:
I pulled off the retaining clip with pliers then removed the old knob and timer dial. I replaced all the parts with the new ones and used pliers to reinstall the clip. The teeth on the new knob engage to select the cycle. https://www.youtube.com/watch?v=cQwLtRcHx9k Read more
The Washer Fill Hoses are OEM parts for various washing machines, specifically designed to transport hot and cold water from the home's supply lines to the washer. These hoses are essential for the proper functioning of the washing machine, ensuring a steady and reliable flow of water during the wash and rinse cycles. Coming in packs of 2, each hose measures 5 ft.
Causes of bad washer fill hoses can include wear and tear over time, exposure to high water pressure, or damage from kinks and bends. Additionally, hoses can deteriorate due to exposure to harsh water conditions or chemical buildup.
Symptoms of bad washer fill hoses include:
These washer fill hoses are compatible with a variety of washing machine brands and models, ensuring a secure and efficient water supply.
Motor control board was flashing 4 times, indicating that the mode shifter had an error. I disconnected the mode shifter's wire from the controller and measured the resistance between the 2 leads with an ohmmeter. Since the reading was infinite, that meant that the mode shifter coil or in-line thermal sensor was electrically open, i.e. bad. As this fix is near a complete tear-down of the washing machine, here are a few tips I discovered. 1) the hub nut is difficult to remove and you need a... Read more
This is a genuine OEM replacement agitator coupling part for washing machines. The role of an agitator coupler is to act as a connector between the agitator and the agitator shaft in the washing machine.If a coupler is damaged, there are some common symptoms that may be noticeable including: a grinding sound during the wash cycle, the washer refusing to agitate or spin, or the washing machine shaking and moving during the wash cycle. Other signs may include very wet clothes or the motor spinning without the drum rotating. Above all, the most common symptom is simply a loud, unpleasant noise while the machine is operating.This replacement agitator coupling part is compatible with General Electric, RCA, JCPenney, and Hotpoint washers. This coupling is used specifically for 20 spline drive shaft transmissions. The agitator coupling piece comes with instructions to make the installation process as quick and simple as possible.
Removing the aluminum hub was ridiculous. this part should come with the rubber piece that is directly below it. removing that rubber piece is essential to the repair and is quite a battle to get off. To remove the aluminum hub ( no fasteners just a friction fit) I tried a 2 arm automotive wheel puller which pulled the arms through the aluminum with out budging the part. I finally resorted to using a Sawsall to cut a vertical slit into the hub down to the shaft so I could split it and get it... Read more
Black. 8-18 AB HXW 3/8
I ordered the part and was impressed to receive it within two day! I didn't need the screws I ordered (which I ordered just in case) but the trim was put on with no problem and my oven looks brand new again! Thank you! Read more
This hose clamp kit secures the washer's hoses at the pump, tub, or valve connections, helping stop leaks and hose blow-offs. Replace worn or missing clamps to restore a tight, reliable seal during fill, wash, and drain.
The video was very helpful. the hardest part is getting off old rusted parts. I had to use a hacksaw to remove one of the old clamps. I had to open the bottom of the washing machine to remove of the other clamp. Putting the new parts on was easy. Getting everything apart was a challenge. Putting the new parts on was an easy 5 minute job. Read more
By GE. Fits many different washer brands and models. Includes insert.
The new GE washers come with a fill valve that has a 1/8" hole for the hot water inlet. This is probably for energy savings or something. So, I installed the older style GE fill valve on my new machine. Since the older style has larger inlet holes for both hot and cold water, it fixed my problem easily. NOTE: The outlet nipple on the new style GE fill valves are larger than the older style. Therefore, I had to make a coupling piece to attach the older style GE valve outlet nipple to the... Read more
Size: 10-12 a. Includes 12 screws.
I have a 14 year old GE washing machine that had been making a lot of noise while running but had eventually just stopped flat. The agitator and spin cycle would not run. I found this site and made excellent use of all the repair videos to study about my issue. I put in my machine model number and I Immediately was able to start honing in on what my problem could be from website advice about popular repair parts, stories others had shared about their similar machine issues and watching videos,... Read more
Includes 12 washers.
I called on your service, a person on the phone name Mr.Berry ask what the matter was . I told him the said a water valve should fix it . it sure was the right fix. thank you guys and thank you Mr. Berry. john m Read more
Package of 12
Watched the repair video. Saw what to look for. Found the dryer drum front support was broken and the slide bearings were worn. Replaced these items. Read more
Fits GE/Hotpoint washers.
Outer basket had a lot of rust on the lip at the top of the basket, I ordered tub gasket, but when I removed the old gasket, some of the lip broke off, leaving gaps at the top, went to the hardware store, and purchased thin sheet of 8x10" aluminum, cut and shaped pieces from this sheet, to fit under the damaged lip, to bridge the gaps, rounded edges to fit against the rounded part of the outer tub, under the lip, once shaped, I glued them in place with emblem adhesive, did this all the way... Read more
This compressor start relay helps the refrigerator compressor start reliably so the appliance can cool properly. It replaces a failed relay to restore normal compressor startup and reduce hard-start symptoms. What it does:
This door gasket seals the refrigerator door to keep cold air in and warm air out, helping maintain proper temperatures and reduce energy use. It replaces a worn, torn, or deformed seal to restore a tight door closure. What it does:
It is an old washing machine that is leaking oil from the transmission, and taking advantage of the disarmament want to change those parts that are damaged.the will rebuild replacing those parts and then paint it. Read more
This support is a replacement mounting bracket that helps secure internal components and restore proper alignment for stable operation. It's a direct-fit shaped bracket that replaces worn or damaged supports to reduce rattling and shifting. What it does: