Parts for Lg LCE30845 / ASTLLGA: Section 2 Parts

A Tap-Tite binding-head screw used to fasten appliance panels and components where a self-tapping metal thread is required. Replaces missing or damaged fasteners to restore secure assembly and reduce vibration or rattling. What it does:

• Creates its own mating thread in thin sheet metal for a secure hold without a nut.
• Holds panels, brackets, and trim in place to prevent looseness or movement.
• Commonly used where stripped, missing, or broken screws cause rattling, misalignment, or parts that won't stay attached.
• Compatible with standard screwdrivers or nut drivers sized to the binding-head.

• Disconnect power and unplug the appliance before working on it.
• Use the correct driver bit to avoid cam-out or head damage.
• Start straight and apply steady pressure; avoid overtightening to prevent stripping the formed threads.
• If the original hole is badly damaged, assess for repair or use of a larger fastener as needed.

This truss head tapping screw secures panels, brackets, and covers in your appliance. Replacing a missing or damaged fastener restores a snug fit, reduces vibration, and helps keep components properly aligned for reliable performance.

• Provides low-profile holding power; wide truss head helps secure thin panels and trim
• Replaces lost, stripped, or corroded screws at the original mounting points
• Helps eliminate rattling, vibration, or loose handles/covers
• Addresses situations where a screw will not tighten or backs out during use

• Disconnect power; shut off water/gas if applicable before servicing
• Align parts and hand-start threads to avoid cross-threading
• Tighten until snug; do not overtighten to prevent stripping
• If the receiving hole is damaged, for repair before installing the new screw

This truss head tapping screw secures interior panels and small components on compatible appliances, restoring proper fit and stopping rattles or loose trim. It's a direct hardware replacement for a single mounting point. What it does:

• Fastens panels, brackets, and trim where a low-profile truss head is required
• Replaces missing or stripped screws that cause rattling or loose parts
• Provides a secure hold by forming threads in sheet metal during installation
• Useful for repairing cosmetic or functional panel alignment issues

• Disconnect power before working on any appliance to avoid shock or injury
• Use the correct sized Phillips or Torx driver to prevent cam-out or screw damage
• Start straight and thread slowly; do not overtighten to avoid stripping sheet metal
• Replace only with the exact part number for best fit and performance

This Base PCB is the primary control board that manages the appliance's main functions, helping coordinate power distribution and control signals so the unit runs cycles and responds to user commands. What it does:

• Routes power and control signals between components and sensors
• Coordinates timing and operation of motors, valves, and relays
• Helps interpret inputs from user controls and sensors
• Can cause loss of functions or erratic behavior when damaged
• Common symptom link: appliance won't start, stops mid-cycle, or shows persistent errors

• One base PCB assembly

• Disconnect power before beginning any repair to avoid shock
• Handle the PCB by its edges and avoid static discharge
• Verify all connectors are fully seated and match their original locations during reassembly

A circular lug designed to join a stripped wire to a threaded terminal for a secure electrical connection. Helps restore reliable contact at terminals and reduces the chance of intermittent power or arcing at connection points. What it does:

• Provides a strong mechanical and electrical connection between a wire and a screw or bolt terminal.
• Helps prevent loose connections that can cause intermittent operation, sparking, or overheating.
• Commonly used where a ring-style termination is required for safe, stable wiring.
• Works with properly sized wire and fasteners to maintain consistent conductivity.

• Always disconnect power to the appliance before inspecting or replacing electrical parts.
• Use the correct lug size and gauge for the wire and terminal; crimp or solder per manufacturer recommendations.
• Tighten terminal hardware to the appliance manufacturer's specified torque; avoid over-tightening which can damage the lug or terminal.
• If wiring insulation or the terminal is damaged or corroded, replace the affected components rather than reusing them.

This idle bracket supports the dryer/tumble assembly's idler pulley so the drive belt stays aligned and tensioned for reliable drum rotation. Replaces a worn or broken bracket to reduce belt slippage and related noise. What it does:

• Secures the idler pulley in the correct position for proper belt tension and tracking
• Prevents belt rubbing, slipping, or premature wear that can cause noisy operation
• Restores stable drum rotation when a cracked or damaged bracket is the cause of belt issues
• Helps maintain correct alignment of the drive belt and pulley system

• Disconnect power (unplug or turn off breaker) before beginning any repair
• Support the drum and/or belt while removing and reinstalling the bracket to avoid misalignment
• Use common hand tools; retain original fasteners unless replacements are specified
• After installation, test the dryer through a short cycle to ensure smooth, quiet operation