Parts for Ge TBT14DAXLRAD: 01 - Section1 Parts

Assembly screw kit for refrigerators. Secures handles, shelf tracks, door hinges, and interior panels. Replace missing, stripped, or lost screws.

Door shelf bar installs on the refrigerator door to create storage compartments for condiments and small items. Replace if cracked, broken, or missing.

White plastic end cap for refrigerator door shelf bars. Snaps onto bar ends to hold shelves securely in place. Replace cracked, broken, or missing caps.

Covers and secures the ends of refrigerator door shelves and bins. Replace if cracked, broken, or missing to restore a finished look and prevent items from sliding off.

Freezer door gasket creates an airtight seal to keep cold air in. Replace when cracked, torn, or door won't seal properly. Verify fit by model number.

Due to manufacturer changes part will be longer than original and must be cut to size. It may also be redesigned in color.

Includes 12 screws. Size: 8-18 ab.

Seals your refrigerator door to keep cold air in and warm air out. Replace if you notice condensation, frost buildup, or higher energy bills.

Replacement dairy compartment door for refrigerator door storage. Needed when original is cracked, broken, or missing. Installs in door compartment.

Replacement door shelf bar for GE refrigerators. Secures bottles, jars, and condiments on door shelves. Order if your original bar is cracked, broken, or missing.

Plastic end cap that covers exposed trim edges and screw openings on refrigerator handles and trim. Replace if cracked, broken, or missing for a finished look.

This is a snap-in plug button used to replace a missing or damaged control panel or trim cap on compatible GE appliances. It restores a finished look and helps keep the underlying fastener or opening covered. What it does:

• Covers and protects a small access hole or fastener opening on the appliance surface
• Snaps into place to hold trim panels or control overlays secure
• Replaces worn, cracked, or missing buttons that affect appearance or allow debris entry
• Common symptom: visible hole or loose/missing plug on control panel or exterior trim

• One plug button

• Snap-in installation; press firmly into the opening until fully seated
• No tools typically required; use a soft cloth to protect finish while pressing
• If the surrounding area is damaged or warped, part may not seat correctly
• Disconnect power to appliance before working near energized controls or panels

Mounting bracket that secures shelves and internal components in your refrigerator. Replace if cracked, broken, or missing to keep shelves stable and prevent shifting.

Replacement meat pan drawer for the fresh food section. Restores organized storage when original is cracked, broken, or missing. Slides into shelf rails.

Replaces a cracked or missing support rail cover trim piece on your refrigerator. Restores a finished look where the support rail meets the cabinet.

Clear lower crisper drawer for refrigerator vegetable storage. Replace your cracked, broken, or missing drawer to restore organized produce storage.

White plastic frame with glass insert that covers the crisper drawer in your refrigerator. Replace if cracked, broken, or glass is shattered. Easy install.

Rear mobility wheel mounts to the back base of your refrigerator. Replace if worn, cracked, or causing uneven rolling when moving the unit for cleaning.

The GE access cover is an OEM replacement part responsible for covering the compressor area on a refrigerator. This panel is located on the rear or bottom of the refrigerator and provides easy access to the compressor and condenser coils and prevents dirt and debris from entering the compressor area. When this part becomes damaged, it can lead to issues such as poor cooling performance, excessive noise from the compressor area, or even compressor overheating.

Symptoms of a bad access cover include:

• Visible cracks, breaks, or deformation in the cover
• Difficulty in securing the cover properly in place
• Increased dust or debris buildup inside the refrigerator
• Exposed internal components

Causes of a bad access cover can include accidental impacts, wear and tear from frequent removal and reinstallation, and environmental factors like temperature fluctuations or moisture exposure.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Rear rail support plate for refrigerators. Mounts inside the cabinet to support shelving rails. Replace if cracked, broken, or missing for stability.

Positions refrigerator door components with correct clearance for smooth swinging and level alignment. Replace if worn, cracked, or missing to restore fit.

Replace the right-hand mounting gusset bracket in your top-mount refrigerator. Needed when the original bracket is cracked, broken, or missing.

Insulation foam that protects electrical components in your top-mount refrigerator. Replace if cracked, deteriorated, or missing to maintain proper coverage.

The Light Socket is an OEM part for GE refrigerators. It is responsible for holding the refrigerator's light bulb and ensuring it receives power to illuminate the interior when the door is opened.

You should replace the light socket if it becomes faulty. Causes of a bad light socket can include wear and tear from regular use, electrical issues such as short circuits or power surges, and corrosion from moisture exposure.

Symptoms of a bad light socket include:

• The refrigerator light not turning on when the door is opened
• Flickering or intermittent light operation
• Visible damage or corrosion on the socket
• The light bulb not fitting securely or falling out

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

2 wire insulator.

Replacement screw for refrigerators. Secures handles, panels, and internal components. Order if yours is missing, stripped, or lost during repairs.

Freezer not cooling or making buzzing noise? The evaporator fan blade circulates cold air. Easy DIY fix in under 5 minutes—simply pull off and press on.

Refrigerator not cooling or compressor clicking on and off? This compressor kit restores cooling. Requires certified technician with specialty tools.

The Run Capacitor is an OEM part for GE refrigerators. It plays a crucial role in the refrigerator's cooling system by providing the necessary start and run voltage to the compressor. Without a properly functioning run capacitor, your refrigerator may struggle to maintain the desired temperature, leading to spoiled food and inefficient energy use.

Causes of a bad run capacitor include electrical surges, wear and tear over time, or overheating due to a malfunctioning refrigerator compressor or poor ventilation.

Symptoms of a bad Run Capacitor include:

• The refrigerator compressor fails to start.
• Unusual humming noises coming from the refrigerator.
• The refrigerator cycles on and off more frequently than normal.
• A noticeable increase in energy consumption as the refrigerator struggles to maintain the proper temperature.

This OEM GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances.

Compressor won't start or kicks out after trying? This overload protector prevents motor damage. DIY-friendly repair, takes about 30 minutes to replace.

Compressor won't start or kicks out after trying? This overload protector prevents motor damage. DIY-friendly repair, takes about 30 minutes to replace.

Replacement mounting screw for securing panels, trim, and internal components in appliances. Needed when original screws are stripped, lost, or damaged.

Size: 10-12 x 1/2 inch.

This part has been discontinued and is no longer available.

Replacement plug button insert for refrigerator panels. Fills holes or covers openings in cabinet or liner. Needed when original is missing, cracked, or broken.