Parts for Kitchenaid KGCT025AAL0: 01 - Section Parts

This part has been discontinued and is no longer available.

A replacement rubber grommet for Whirlpool appliances that cushions and seals openings to protect hoses and wiring from chafing and wear. Restores a snug seal to help reduce leaks, noise, and vibration damage. What it does:

• Cushions and protects wiring, hoses and components where they pass through panels or housings.
• Forms a sealing barrier to help reduce moisture intrusion and small leaks.
• Helps prevent abrasion and wear that can lead to frayed wires or hose damage.
• Common signs it's needed: visible cracking, deformation, or rubbing at an opening.

• Disconnect power (and water/gas where applicable) before servicing the appliance.
• Verify correct location and orientation; press the grommet into the opening until fully seated.
• Use a little mild soap or silicone lubricant to ease installation if tight; avoid petroleum-based solvents.

This grommet is located between the glasstop and the knobs. Color: White. Measures about 2 inches in diameter. For black order W10854242. For biscuit order 3191817.

The Grommet is an OEM part for Whirlpool cooktops. This part provides a secure fit and cushioning for the control knobs on the cooktop, ensuring smooth operation and preventing damage to the control panel.  

Causes of a bad knob grommet can include general wear and tear, exposure to high temperatures, or damage from frequent use.  

Symptoms of a bad knob grommet include:

• Loose or wobbly control knobs
• Difficulty in turning the knobs
• Knobs not staying in place or falling off
• Visible cracks or wear in the grommet

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This factory screw secures appliance components to their mounting points. Replace missing, worn, or stripped hardware to restore a tight fit, proper alignment, and quieter operation across the affected assembly.

• Fastens panels, brackets, covers, or internal parts to the chassis or frame
• Helps maintain alignment and support, reducing rattle, vibration, or looseness
• Replaces missing or damaged screws that have backed out, broken, or stripped
• Restores secure mounting after service when original hardware is lost

• Disconnect power; shut off water or gas supplies before servicing
• Use the correct driver; start threads by hand to avoid cross-threading
• Match length and thread to the original location; do not substitute with longer hardware
• Tighten snugly; do not overtighten into plastic or thin metal

Size: 8-18 x 3/8 inch.

This part has been discontinued by the manufacturer and is no longer available.

This screw is used to secure the handle end cap to the center of the door. The screw size measures 8-18 x 1/2 inches.

Color: black. Measures about 2 inches in diameter.

This replacement gas control knob restores smooth, precise burner adjustment and refreshes the look of your range or cooktop. The almond finish matches original styling for a clean, uniform appearance on compatible gas models.

• Attaches to the surface burner valve stem to control gas flow and flame height
• Common fix for a cracked, stripped, wobbly, or missing knob
• Helps when the pointer no longer aligns or the knob is hard to turn
• Cosmetic refresh for discolored or worn knobs

• Ensure all burners are OFF and the appliance is cool before servicing
• Pull the old knob straight off the valve stem; do not pry against the panel
• Align the new knob with the stem and press straight on until fully seated
• If the knob will not seat, inspect the stem for damage and do not force installation

Color: white. Measures about 2 inches in diameter.

Size: 8-32 x 2 1/2 inch.

This hardware kit contains the small mounting parts needed to secure and support the appliance component. It provides replacement fasteners and brackets to restore proper fit and stability after service. What it does:

• Replaces worn or missing mounting pieces that cause loose panels or components
• Restores proper alignment and support for the associated assembly
• Helps stop rattling, vibration, or movement caused by missing hardware
• Matches OEM fit and function when used as a direct replacement

• Intended for technicians or experienced DIYers; inspect the kit before installation
• Use appropriate hand tools; tighten fasteners to manufacturer torque where specified
• Disconnect power and follow all safety procedures before servicing the appliance
• Replace only the parts shown for your specific model

Gas valve shaft seal.