Parts for Weedeater W25SBK: Shaft / Shield / Handle Parts

This is a trimmer throttle cable assembly meant to be compatible with trimmers from several top brands. The throttle cable is the part that connects the throttle trigger and the carburetor. It can allow the user to provide power to the machine by regulating the carburetor airflow. If the cable has a problem, users will not be able to control the throttle properly or at all in some cases.The throttle cable could become damaged and need to be replaced. There are connections on each end of the cable that could be damaged or broken. The cable might also kink, which could cause it to break. Owners can replace the cable and extend the life of the trimmer. Tools commonly used for replacement include a hex key, Torx screwdriver, or a screwdriver depending on the model.The throttle cable assembly works with certain models of trimmer from Husqvarna, Weed Eater, and Poulan. The cable is sold individually. This is an authentic OEM replacement that has been sourced from the manufacturer.

This genuine OEM trigger is used on several different types of outdoor equipment, including gas trimmers and edgers. The trigger is attached to the throttle cable to control the speed of the spool assembly. With pressure, the trigger pulls the throttle cable, and in turn, speeds up the spinning hub where the cutting is done. It allows for faster or more difficult cuts to be performed. With routine use of the outdoor equipment, the trigger can break, wear out, or malfunction. Without a properly working trigger, the equipment cannot be controlled with the expected manual adjustments.Replacing the trigger on an edger or trimmer is easy and requires only a screwdriver for most makes and models. Wear work gloves when replacing the trigger. Remove the screws from the control handle housing. Remove the trigger from the throttle cable and put the new one on. Screw back into place and replace the control handle housing.This trigger is a replacement part. It is sold separately. The trigger piece works in a wide assortment of both Husqvarna and Weed Eater trimmers and edgers. The trigger is manufactured using rigid, high-quality plastic, and it is yellow.

This part is a fuel line purge bulb with a shaft that is used on trimmers and edgers. The purge bulb allows the operator of the trimmer or edger to pump the fuel into the carburetor. Once the carburetor is full, the excess fuel is then sent back to the gas tank through the return line. This component features a durable rubber bulb and a metal shaft.A new fuel line purge bulb with a shaft may be needed if pressing on the bulb does not cause the fuel to pump into the carburetor. If any component of the fuel line purge bulb and the shaft is cracked, broken, or damaged in any way, it will need to be replaced. Never perform care and maintenance on outdoor power equipment that is powered on. Remember to wear gloves when operating or performing care and maintenance on any outdoor power equipment.This fuel line purge bulb with a shaft is a genuine Husqvarna part. It is sold individually. This particular fuel line purge bulb with a shaft is compatible with trimmers and edgers that are manufactured by Weed Eater.

This replacement part is a drive shaft kit and is intended for use in different types of lawn equipment. This is a genuine replacement part made by Husqvarna. This part is used in weed eaters and line trimmers and helps the user operate the appliance properly. This part allows the user to maintain full control over the appliance to get landscaping jobs done.A new drive shaft kit might be needed if the current part is damaged or broken in anyway including being dented, cracked, or snapped. It is possible that due to normal wear and tear this part becomes worn down overtime. Be sure to wear work gloves while replacing this part to prevent injury. Refer to the owners manual for more specific instructions on how to replace this part. This is a genuine OEM replacement part that is sourced directly from the manufacturer to ensure a proper fit and long lasting results. This part is sold individually.

This replacement part is a shaft assembly and is intended for use in a variety of lawn equipment. This is a genuine replacement part made by Husqvarna. This shaft assembly is typically found in grass trimmers. The shaft assembly connects the top of the trimmer to the bottom mechanisms which allow the user to control the settings in the trimmer. A new shaft assembly might be needed if the user is unable to control the gear at the lower end of the trimmer. It is possible that the shaft can become damaged with normal wear and tear. Be sure the equipment is completely powered down and cooled off before attempting to repair an appliance. For more detailed instructions on how to install this specific part, see the owner's manual. This is an OEM part sourced directly from the manufacturer. It is sold individually. This replacement part is compatible with different types of lawn equipment made by Husqvarna.

This part is a replacement spring. This is a genuine OEM part made by Husqvarna and has been sourced directly from the manufacturer. If the current spring is broken or defective, this part can be used as a replacement. It is intended for use with trimmers.The spring works by applying tension to the head of the trimmer. Over time and with regular use, springs can easily break or become eroded, requiring replacement. When working on or near an engine or blades, always ensure that the equipment is powered off and completely cooled down before attempting to undergo any repairs. For more accurate information on how and where to install this spring, the appropriate owner's manual and equipment diagrams should be referenced. This spring is suitable for use on a variety of trimmer models manufactured by Husqvarna and Poulan. It is a genuine OEM part and thus is made of high-quality, durable metal. Part sold individually.

This is a wound spool assembly that can be used on several models of lawn and garden equipment. The spool assembly is the part that holds the trimming line. It also operates by letting the line feed out when a trimmer or pruner is being used. The wound spool assembly is a component of the cutting head assembly but can be replaced as a single part. This wound spool assembly part experiences a great amount of wear and tear. It's not a bad idea to have an extra available for any needed replacement. If the spool assembly is broken or damaged, it can be replaced in just a few minutes. The first step is to power off the equipment and remove the spark plug wire. The cover should be removed to get access to the wound spool assembly. Switch it out with the replacement part.This wound spool assembly is sold as an individual part. It is a genuine OEM replacement part that is directly sourced from the manufacturer. The spool assembly is designed to be compatible with string trimmers and pole pruners manufactured by Poulan, Poulan Pro, and Husqvarna.

This is the outer cover for a string trimmer housing. It clips into the bottom of the reel and secures it in place behind the central button. It’s constructed from a rubberized black plastic. This plastic is designed to be as durable as possible, while also flexing slightly when it’s under pressure. The cover serves two primary functions. It holds the reel in place and also acts as a mounting point for the central button. While it’s quite durable, it may eventually wear out due to regular use. A few scratches aren’t going to put a cover out of commission, but look for areas where the plastic has been worn through all the way. Replacing the cover is easy. Simply squeeze the old cover and pop it off the assembly. Position the new cover over the reel, then snap it into place. This cover is used primarily on Husqvarna string trimmers but is also used on some Poulan and Craftsman models. This is an OEM part sourced directly from Husqvarna, and it is sold individually.

This is the outer cover for a string trimmer housing. It clips into the bottom of the reel and secures it in place behind the central button. It’s constructed from a rubberized black plastic. This plastic is designed to be as durable as possible, while also flexing slightly when it’s under pressure. The cover serves two primary functions. It holds the reel in place and also acts as a mounting point for the central button. While it’s quite durable, it may eventually wear out due to regular use. A few scratches aren’t going to put a cover out of commission, but look for areas where the plastic has been worn through all the way. Replacing the cover is easy. Simply squeeze the old cover and pop it off the assembly. Position the new cover over the reel, then snap it into place. This cover is used primarily on Husqvarna string trimmers but is also used on some Poulan and Craftsman models. This is an OEM part sourced directly from Husqvarna, and it is sold individually.

This is a replacement knob for a trimmer. The plastic bump knob, which is connected to a spring, is used to secure the spool. A bump knob on a trimmer may get stuck or seized and will need a replacement. Before replacing the bump knob, remove the wire from the spark plug to avoid the accidental starting of the engine. Pull off the trimmer head housing and then use a flat head screwdriver to detach the old knob. Rotate it and then remove the component. Make sure the spring is in place then align the knob before rotating and snapping it in place. Take note that pulling the knob off may take extreme force when pulling. Some knobs are screw-mounted and a counterclockwise turn is necessary to unscrew it. This genuine OEM replacement part is sold individually and is compatible with specific trimmer models from Poulan and Weed Eater.