Parts for Maytag M8TXEGFBB00: 03 - Shelf Parts

Restore stable, level storage with this full-width refrigerator glass shelf. It replaces a cracked, missing, or unstable shelf so you can safely organize food and help keep messes contained within the shelf area.

• Spans the compartment to provide a sturdy, level surface for food and containers
• Helps contain small spills to limit messes reaching lower shelves or drawers
• Replace if the glass is cracked/chipped, the shelf sags, or it no longer seats securely
• Restores the intended fit and usable storage space for the designated shelf position

• Clear the area and remove the old shelf
• Angle the shelf as needed; insert the rear into the side-wall supports, then lower the front until fully seated
• Handle glass by the edges and wear cut-resistant gloves
• Do not force; ensure the shelf is aligned with the correct support slots

This center rail track supports and guides a sliding assembly inside your appliance, keeping the rack or drawer aligned and moving smoothly. Replace a cracked or bent center track to restore easy, stable operation and reduce binding. What it does:

• Provides the middle guide surface for a slide system
• Maintains level alignment with the mating rails
• Allows smooth in-and-out travel of the rack/drawer
• Typical symptoms: sticking or rough movement, derailment, tilting, or visible cracks/warping

• 1 center rail track

• Unplug or disconnect power before servicing; shut off gas if applicable
• Remove the rack/drawer and note the rail's orientation for reassembly
• Reuse existing fasteners and transfer any clips/brackets from the old track
• Test for smooth travel before returning to service

The Refrigerator Track is an OEM part for Whirlpool refrigerators. It supports and guides the movement of refrigerator drawers or shelves, ensuring they slide in and out smoothly. The track measures approximately 11 inches in length.

Causes of a bad track can include wear and tear from frequent use, damage from overloading the drawers or shelves, or breakage due to accidental impact. Over time, the track can become misaligned, cracked, or lose its ability to support the drawer properly.

Symptoms of a bad track include:

• Drawers or shelves that do not slide smoothly or get stuck
• Uneven or tilted drawers
• Noise when opening or closing the drawers
• The track appears damaged or broken

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Refrigerator Drawer Track is an OEM part for Whirlpool refrigerators. It provides a stable guide for the refrigerator drawers, ensuring they slide in and out smoothly for easy access to stored items.

Causes of a bad drawer track can include normal wear and tear from frequent use, buildup of dirt and debris, or physical damage from overloading the drawers or accidental impact. When the track becomes worn or damaged, it can impede the drawer's functionality.

Symptoms of a bad drawer track include:

• Difficulty opening or closing the refrigerator drawers
• Drawers getting stuck or not sliding smoothly
• Misalignment or falling off the tracks
• Unusual noises when operating the drawers

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This humidity control graphic is the replacement label for the crisper drawer humidity slider, restoring clear markings so you can set and read the vent position easily. It helps make humidity settings visible and intuitive. What it does:

• Replaces worn, faded or missing humidity-slider markings on the crisper vent
• Restores clear low/med/high or open/closed indicators for accurate vent position reading
• Helps prevent confusion when adjusting drawer humidity for produce storage
• Matches OEM appearance and placement to maintain original look

• One humidity control graphic/label for the crisper humidity slider

• Disconnect power to the appliance before accessing interior components when required
• Remove the crisper drawer and clean the mounting area; peel-and-stick or snap-in fit may be adhesive-backed
• Align the graphic carefully before attaching to avoid rework; press firmly to ensure full adhesion

This freezer shelf mounting cup fits into the liner opening to support the ribbed freezer shelf post, keeping the shelf level and secure. Replace cracked or missing cups to restore proper shelf support and prevent sagging.

• Supports the ribbed freezer shelf post and anchors it in the liner
• Helps keep the shelf level and properly positioned
• Replaces cracked, worn, or missing cups
• Common symptoms: shelf tilts, won't stay in place, rattles, or falls

• Unplug the refrigerator before starting
• Remove the freezer shelf; carefully pry the old cup straight out of the liner opening to avoid damage
• Press the new cup fully into the opening until flush; reinstall the shelf post into the cup
• Verify the shelf is seated and level before loading items

This 16-inch meat pan is a replacement oven accessory that catches drips and holds roasts or pans for even cooking. It restores oven functionality and keeps the oven interior cleaner during broiling and roasting. What it does:

• Collects drips and juices while roasting or broiling to protect the oven bottom
• Provides a flat, stable surface for small pans, roasts, and other bakeware
• Helps promote even heat distribution for items placed directly on the pan
• Reduces the need for frequent oven cleanings by containing spills

• One 16-inch meat pan

• Fits into existing oven rack slots; no tools required for installation
• Allow pan to cool before handling; use oven mitts when hot
• Inspect pan for warping or heavy corrosion before use; replace if damaged
• Follow oven manufacturer's guidance for broiling and cleaning to avoid damage